Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Audio Technica AT-ONE
Summary of Contents for Audio Technica AT-ONE
- Page 1 UHF Wireless Microphone System Installation and Operation...
-
Page 2: Table Of Contents
Contents Introduction - Introduction - Safety System Functions - Receiver Functions - Handheld Transmitter Functions - Bodypack Transmitter Functions - Battery Status System Operation - System Setup - Receiver Operation - Transmitter Operation - Squelch - Frequencies - Troubleshooting - Rack Mount Setup Specifications - Overall Specification - Receiver Specification... -
Page 3: Introduction
Thank you for purchasing this Audio-Technica product. This PLL synthesized wireless microphone system operates in the UHF band frequency, with two groups of four frequencies. Please read this manual carefully before operating the AT-One system. This manual covers the function and operation of the wireless microphone system. -
Page 4: Receiver Functions
Receiver Functions Receiver Front: 1. Antenna: Detachable UHF antenna with BNC connector 2. Power Button 3. RF Red LED: Displays the reception status of the RF signal 4. AF Green LED: Displays the reception status of the AF signal 5. UP Channel Button: Tap forward to select an interference free channel 6. - Page 5 Receiver Functions Receiver Rear: 1. Antenna BNC Receptacle: This provides a connection to the supplied antennas or to coaxial cable used with an antenna divider, antenna booster or remote antennas 2. Balanced XLR Audio Output 3. Unbalanced 1/4” Jack Output Use this to adjust the audio output of the wireless 4.
-
Page 6: Handheld Transmitter Functions
Transmitter Functions Handheld Transmitter: 1. Power/Mute Button 2. Power/Mute/Battery Status LED Indicates the power/mute/battery level status 3. Channel Selector: Change the channel setting from 11-14 or 21-24 Insert two AA batteries making sure the polarity is correct 4. Battery Compartment: 5. -
Page 7: Bodypack Transmitter Functions
Transmitter Functions Bodypack Transmitter: 1. Antenna 2. Power/Mute Button 3. Power/Mute/Battery Status LED: Indicates the power/mute/battery level status 4. Input Connector: 4-pin locking connector (HRS) 5. Channel Selector: Change the channel setting from 11-14 or 21-24 6. Gain: Rotary control adjusts the sensitivity of the transmitter’s audio to the level of the connected mic or instrument 7. -
Page 8: Battery Status
Transmitter Functions Power/Battery Status LED Status Green Ready Muted Green Flashing On, low battery Red Flashing Muted, low battery No Light No power System Operation System Setup: For best operation the receiver should be at least 1 m above the ground and at least 1m away from a wall or metal surface to minimize reflections. -
Page 9: Receiver Operation
System Operation Connecting the receiver: Plug the DC 12V 500mA power supply into the power connector on the back of the receiver. The power connector is supplied with interchangable UK and EU adaptors. Connect the receiver output to an audio mixer or amplifier input, using a standard audio cable with 3-pin XLR or 6.35mm Jack connectors. -
Page 10: Transmitter Operation
System Operation Handheld Microphone/Bodypack Transmitter set up: Open the battery cover and insert AA batteries into the battery compartment making sure the polarity is correct. Unscrew the bottom of the handheld mic and open the battery cover to insert AA batteries into the battery compartment, making sure the polarity is correct. -
Page 11: Squelch
830.850 828.650 Each AT-One system comes with Group 1 and Group 2 frequencies available as shown in the table above. The system has been designed in these groups to allow you to use up to four channels in one group together, interference free (subject to national licensing and regulations). -
Page 12: Troubleshooting
System Operation Troubleshooting Problem Solution No Sound - Check the power supply of the transmitter and receiver - Check that the transmitter and receiver are tuned to the same frequency - Check that the receiver is correctly connected to the mixer or amplifier - Check whether the transmitter is too far from the receiver or the Squelch control is set too high - Check for obstuctions between the transmitter and receiver... -
Page 13: Rackmount Setup
System Operation Rackmount Setup: To mount the receiver in a 19”standard rack using the included rack kit, attach the L shaped brackets to the opposite end of the unit and mount in the rack unit. To connect two receivers in a 19”standard rack using the optional AT8677 rack kit, attach the short L shaped brackets to the opposite end of each unit, and connect the units together using two metal connecting plates. -
Page 14: Specifications
Specifications Overall System Frequency range: 824 - 831 MHz, 863 - 865 MHz Modulation mode: Number of frequencies: 2 x 4 frequencies Operating range: 60m, typical Frequency response: 60 HZ - 16 kHz +/- 0.005%, phase lock loop frequency control Frequency stability: Receiver Specifications Antenna switching diversity... -
Page 15: Bodypack Transmitter Specification
Specifications Body-Pack Transmitter RF Output power: 10 mW Spurious Emissions: Follows national regulations Input connections: Pin 1: GND Pin 2: INST Pin 3: Mic Pin 4: DC Bias + 10 V Batteries (not included): Two 1.5 V AA alkaline Battery Life: 10 hours - depending on battery type and use pattern Dimensions: 66 mm x 98 mm x 22 mm (W x H x D) -
Page 16: Weee Regulations
WEEE Regulations... -
Page 17: Declaration Of Compliance
finden Sie unter folgender Internet-Adresse: eu.audio-technica.com/doc GR Με το παρών , η Audio Technica Corp., δηλώνει ότι τα ATW-T1F , ATW-T3F και ATW-R1F συ φωνούν ε την οδηγία 1999/5/EC . Το πλήρε κεί ενο τη οδηγία τη EU ( ∆ήλωση... - Page 18 Audio-Technica Ltd Technica House Unit 5 Millenium Way Leeds LS11 5AL UNITED KINGDOM Tel: +44(0) 113 2771441 Fax: +44(0) 113 2704836 Audio-Technica SAS 11 Rue des Pyramides 75001 Paris FRANCE Tel: +33(0) 1 43 728282 Fax: +33(0) 1 43 726070 Audio-Technica Niederlassung Deutschland Lorenz-Schott-Str.