Pro-Form 365p User Manual page 4

21. Inspect and properly tighten all parts of the
treadmill regularly.
22. Never insert any object into any opening.
DANGER:
23. Always unplug the power
cord immediately after use, before cleaning the
treadmill, and before performing the mainte-
nance and adjustment procedures described in
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decal shown has been placed on the treadmill. If the decal is missing, or if it is not legible, please
call our Customer Service Department to order a free replacement decal (see the back cover of this man-
ual). Apply the decal in the location shown. Note: The decal is not shown at actual size.
this manual. Never remove the motor hood un-
less instructed to do so by an authorised ser-
vice representative. Servicing other than the
procedures in this manual should be performed
by an authorised service representative only.
24. The treadmill is intended for in-home use
only. Do not use the treadmill in a commer-
cial, rental, or institutional setting.
4
Locate the Reed Switch (16) and the Magnet (10) on
the left side of the Pulley (101). Turn the Pulley until
the Magnet is aligned with the Reed Switch. Make
sure that the gap between the Magnet and the
Reed Switch is about 3 mm (1/8 in.). If necessary,
loosen the indicated Screw (78), move the Reed
Switch slightly, and then retighten the Screw. Reattach
the Hood (not shown), and run the treadmill for a few
minutes to check for a correct speed reading.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. If an extension cord is needed, use only a 3-conductor, 1mm
than 1.5 m (5 ft.).
b. If the walking belt is overtightened, treadmill perfor-
mance may decrease and the walking belt may be-
come damaged. Remove the key and UNPLUG THE
POWER CORD. Using the hex key, turn both rear
roller adjustment bolts counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you
should be able to lift each side of the walking belt
8–10 cm (3–4 in.) off the walking platform. Be careful
to keep the walking belt centred. Plug in the power
cord, insert the key, and run the treadmill for a few
minutes. Repeat until the walking belt is properly tight-
ened.
c. If the walking belt still slows when walked on, call our Customer Service Department.
PROBLEM: The walking belt is off-centre or slips when walked on
SOLUTION: a. If the walking belt is off-centre, remove the key and
UNPLUG THE POWER CORD. If the walking belt
has shifted to the left, use the hex key to turn the left
rear roller bolt clockwise 1/2 of a turn; if the walking
belt has shifted to the right, turn the left rear roller
bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Plug in the power cord,
insert the key, and run the treadmill for a few minutes.
Repeat until the walking belt is centred.
b. If the walking belt slips when walked on, first remove
the key and UNPLUG THE POWER CORD. Using
the hex key, turn both rear roller bolts clockwise, 1/4
of a turn. When the walking belt is correctly tightened,
you should be able to lift each side of the walking belt
8–10 cm (3–4 in.) off the walking platform. Be careful
to keep the walking belt centred. Plug in the power
cord, insert the key, and walk on the treadmill for a
few minutes. Repeat until the walking belt is properly
tightened.
101
78
16
10
3 mm
Top View
2 (14-gauge) cord that is no longer
b
8–10 cm
Rear Roller Adjustment Bolts
a
b
17