D-Link DES-1016D User Manual
D-link system 10/100 nway ethernet/ fast ethernet switch user's guide des-1016d
Hide thumbs
Also See for DES-1016D:
- Quick installation manual (33 pages) ,
- Quick install manual (20 pages) ,
- Manual (20 pages)
Related Manuals for D-Link DES-1016D
Summary of Contents for D-Link DES-1016D
- Page 1 DES-1016D 10/100 NWay Ethernet/ Fast Ethernet Switch User’s Guide First Edition (Sept., 1999) 6DES1016D.02 Printed In Taiwan RECYCLABLE...
-
Page 2: Wichtige Sicherheitshinweise
Wichtige Sicherheitshinweise Bitte lesen Sie sich diese Hinweise sorgfältig durch. Heben Sie diese Anleitung für den spätern Gebrauch auf. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Vervenden Sie keine Flüssig- oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. Um eine Beschädigung des Gerätes zu vermeiden sollten Sie nur Zubehörteile verwenden, die vom Hersteller zugelassen sind. -
Page 3: Limited Warranty
Registration Card. If a Registration Card for the product in question has not been returned to a D-Link office, then a proof of purchase (such as a copy of the dated purchase invoice) must be provided when requesting warranty service. The term "purchase" in this software warranty refers to the purchase transaction and resulting license to use such software. - Page 4 D-Link Offices for Registration and Warranty Service The product's Registration Card, provided at the back of this manual, must be sent to a D-Link office. To obtain an RMA number for warranty service as to a hardware product, or to obtain warranty service as to a software product, contact the D-Link office nearest you.
-
Page 5: Limitation Of Liability
LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE OR USE OF D-LINK'S PRODUCTS. D-LINK SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY THE CUSTOMER'S OR... -
Page 6: Copyright Statement
Trademarks Copyright 1999 D-Link Corporation. Contents subject to change without prior notice. D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. All other trademarks belong to their respective proprietors. Copyright Statement No part of this publication may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems Inc., as stipulated by the... -
Page 7: Table Of Contents
OWER ON LED Indicators...7 Power Failure ...7 IDENTIFYING EXTERNAL COMPONENTS...8 ...8 RONT ANEL ...9 ANEL LED I ...9 NDICATORS CONNECTING THE SWITCH ...11 PC...11 WITCH TO ) ...12 WITCH TO WITH PLINK 10BASE-T Hub ...13 100BASE-TX Hub...13 (MDI-II) ...13 UB WITHOUT... - Page 8 TECHNICAL SPECIFICATIONS ...15 RJ-45 PIN SPECIFICATION ...18...
-
Page 9: About This Guide
16-port 10/100Mbps NWay Ethernet/Fast Ethernet Switch. Terms/Usage For simplicity, this documentation uses the term “Switch” (first letter upper case) to refer to the DES-1016D Switch, and “switch” (first letter lower case) to refer to all switches, including the DES- 1016D. - Page 10 Switch. Chapter 3, “Identifying External Components.” Describes the front panel, rear panel, and LED indicators of the Switch. Chapter 4, “Connecting the Switch.” Tells how you can connect the Switch to your Ethernet network.
-
Page 11: Introduction
The Switch supports auto-negotiation, allowing both 10Mbps and 100Mbps operation in full-duplex or half-duplex mode, even on all ports simultaneously. Low price and compact dimensions make the Switch suitable for small medium-size workgroups well... -
Page 12: Performance Features
10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide Performance features Sixteen high-performance 10/100Mbps NWay ports; all ports can auto-negotiate for full- or half-duplex operation Uplink (MDI-II) port for straight-through connection to another switch, hub or repeater Full wire-speed forwarding for 100Mbps Fast Ethernet... -
Page 13: Unpacking And Setup
This chapter provides unpacking and setup information for the Switch. Unpacking Open the shipping carton of the Switch and carefully unpack its contents. The carton should contain the following items: One 10/100 NWay Ethernet/Fast Ethernet Switch One AC power cord This User’s Guide... -
Page 14: Setup
Switch. Desktop or Shelf Installation When installing the Switch on a desktop or shelf, the rubber feet included with the device must be first attached. Attach these cushioning feet on the bottom at each corner of the device. Allow enough ventilation space between the device and the objects around it. -
Page 15: Rack Installation
Figure 2.1 10/100 NWay Ethernet/Fast Ethernet Switch installed on a Desktop or Shelf Rack Installation The Switch can be mounted in an EIA standard size, 19-inch rack, which can be placed in a wiring closet with other equipment. For information about the DFE-700B Rack Mounting Brackets, consult your computer hardware dealer. -
Page 16: Power On
Switch in an equipment rack Power on The Switch can be used with AC power sources 100 - 240 VAC, 50 - 60 Hz. The power switch is located at the rear of the unit adjacent to the AC power connector. To turn the Switch on, press the power switch to the on or “1”... -
Page 17: Led Indicators
The power LED indicator will remain ON. Power Failure As a precaution, the Switch should be turned OFF in case of a power failure. Press the power switch to the off or “0” position. When power is resumed, turn the Switch ON. At all times, avoid leaving the Switch ON if a power failure is anticipated. -
Page 18: Identifying External Components
This chapter describes the front panel, rear panel, and LED indicators of the Switch. Front Panel The front panel of the Switch consists of sixteen (10/100 Mbps MDI-X) ports, one uplink (MDI-II) port, and LED indicators. A description of the ports appears in the Introduction of this User’s Guide (see Features, Chapter 1). -
Page 19: Rear Panel
Supported input voltages range from 100 ~ 240 VAC at 50 ~ 60 Hz. Power Switch This turns the Switch on and off. To turn on the system, press the switch to the “1” position; to turn off, press the switch to the “0”... - Page 20 10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide Figure 3.3 The 10/100 NWay Ethernet/Fast Ethernet Switch LED indicators Power This indicator operates when the Switch is turned on. If this indicator is not lit, check the AC power connector to ensure proper insertion of the power cord and that the power switch is turned ON.
-
Page 21: Connecting The Switch
Ethernet/Fast Ethernet Switch to your Fast Ethernet network. Switch to PC A PC can be connected to the Switch via a two-pair Category 3, 4, 5 UTP/STP straight cable (Cat. 3, 4, and 5 for 10M and Cat. 5 for 100M). -
Page 22: Switch To Hub (With Uplink)
2. The Link/Act LED indicator illuminates upon hookup. Switch to Hub (with Uplink) A hub (10 or 100BASE-TX) can be connected to the Switch via a two-pair Category 3, 4, 5 UTP/STP straight cable. The connection is accomplished from the hub’s Uplink (MDI-II) port to any of the Switch’s (MDI-X) ports. -
Page 23: 10Base-T Hub
10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide 10BASE-T Hub For a 10BASE-T hub, the Switch’s LED indicators should illuminate the following: 100Mbps LED speed indicator is OFF. Link/Act indicator is ON. 100BASE-TX Hub For a 100BASE-TX hub, the Switch’s LED indicators should illuminate the following: 100Mbps LED speed indicator is ON. -
Page 24: Using Straight Cable
Using straight cable When using straight cable, the connection can be made from the Uplink (MDI-II) port of the Switch to any port of the Hub. Using crossover cable When using crossover cable, the connection can be made from any MDI-X ports of the Switch to any port of the Hub. - Page 25 10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide PECIFICATIONS General Standards: IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100 BASE-TX Fast Ethernet ANSI/IEEE std. 802.3 NWay auto-negotiation Protocol: CSMA/CD Ethernet Data Transfer Rate: Ethernet: 10 Mbps (half duplex) 20 Mbps (full duplex)
-
Page 26: Physical And Environmental
10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide General Number of Ports: 16 x 10BASE-T/100BASE-TX ports Media Interface 1 x MDI-II RJ-45 shared with port 1 Exchange: Physical and Environmental AC inputs: 100 – 240 VAC, 50/60 Hz Power Consumption: 24 watts maximum... - Page 27 10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide Packet Filtering/Forwarding 14,880 pps per port (for 10Mbps) Rate: 148,800 pps per port (for 100Mbps) MAC Address Learning: Up to 8K MAC address table Technical Specifications...
- Page 28 RJ-45 P PECIFICATION When connecting the 10/100 NWay Ethernet/Fast Ethernet Switch to another switch, a bridge or a hub, a modified crossover cable is necessary. Please review these products for matching cable pin assignment. The following diagram and tables show the standard RJ-45...
- Page 29 The standard Category 3 cable, RJ-45 pin assignment The following shows straight cable and crossover cable connection: Straight cable for Switch (Uplink MDI-II port) to switch/Hub or other devices connection Crossover cable for Switch (MDI-X port) to switch/hub or other...
- Page 31 2F, No. 233-2 Pao-Chiao Rd, Hsin-Tien, Taipei, Taiwan, R.O.C. TEL: 886-2-2916-1600 FAX: 886-2-2914-6299 WEB: www.dlink.com.tw U.K. D-LINK (EUROPE) LTD. D-Link House, 6 Garland Road, Stanmore, Middlesex HA7 1DP U.K. TEL: 44-181-235-5555 FAX: 44-181-235-5500 WEB: www.dlink.co.uk E-MAIL: info@dlink.co.uk U.S.A. D-LINK SYSTEMS, INC.
-
Page 32: Registration Card
3. What network protocol(s) does your organization use ? !XNS/IPX !TCP/IP !DECnet !Others_____________________________ 4. What network operating system(s) does your organization use ? !D-Link LANsmart !Novell NetWare !NetWare Lite !SCO Unix/Xenix !PC NFS !3Com 3+Open !Banyan Vines !DECnet Pathwork !Windows NT !Windows NTAS !Windows '95 !Others__________________________________________ 5.