Attaching The Front Handle - Ryobi RBC430SBS Operator's Manual

EN
FR DE ES IT
the box. Make sure that all items listed in the packing
list are included.
Inspect the tool carefully to make sure no breakage
■
or damage occurred during shipping.
Do not discard the packing material until you have
■
carefully inspected and satisfactorily operated the
tool.
If any parts are damaged or missing do not operate
■
this product until the parts are replaced.
WARNING:
If any parts are damaged or missing do not
operate this product until the parts are replaced.
Failure to heed this warning could result in
serious personal injury.
WARNING:
Do not attempt to modify this product or create
accessories not recommended for use with this
product. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
WARNING:
To prevent accidental starting that could cause
serious personal injury, always disconnect the
engine spark plug wire from the spark plug pack
when assembling parts.
INSTALLING THE POWER HEAD SHAFT TO THE
ATTACHMENT
See Figure 2.
WARNING:
Never install, remove, or adjust any attachment
while power head is running. Failure to stop the
engine can cause serious personal injury.
The attachment connects to the power head shaft by
means of a coupler device.
Loosen the knob on the coupler of the power head
■
shaft and remove the end cap from the attachment.
Push in the button located on the attachment shaft.
■
Align the button with the guide recess on the power
head coupler and slide the two shafts together.
Rotate the attachment shaft until the button locks into
the positioning hole.
NOTE: If the button does not release completely in the
positioning hole, the shafts are not locked into place.
Slightly rotate from side to side until the button is locked
into place.
Tighten the knob securely.
■
WARNING:
Be certain the knob is fully tightened before
PT NL SV DA NO FI
English (original instructions)
HU CS RU RO PL SL
operating equipment; check it periodically for
tightness during use to avoid serious personal injury.
REMOVING THE ATTACHMENT FROM THE POWER
HEAD
For removing or changing the attachment:
Loosen the knob.
■
Push in the button and twist the shafts to remove and
■
separate ends.
ATTACHING THE HANGER CAP
See Figure 3.
There are two ways to hang your attachment for storage.
To use the hanger cap, push in the button and place
■
the hanger cap over end of the lower end attachment
shaft. Slightly rotate the cap from side to side until the
button locks into place.
The secondary hole in the attachment shaft can be
■
used for hanging purposes as well.

ATTACHING THE FRONT HANDLE

See Figure 4.
RBC430SES
Install the front handle onto the top side of the drive
■
shaft boom with the barrier bar on the same side as
the recoil starter (compare to product images in figure
sheet or on giftbox)
Reinstall the clamp, align the screw to the screw hole
■
on the front handle.
Tighten bolts securely.
■
RBC430SBS
NOTE: The throttle trigger must be mounted to the
operator's right side.
Remove the clamp (Item 28),
■
Place the handle in the bracket (Item 30) located on
■
the shaft housing.
Hold the stamping clamp and align the bolts into the
■
bracket.
Adjust the handle bar for best operator control in a
■
comfortable upright position.
Tighten bolts with the stamping wrench to hold the
■
bike handle securely.
ATTACHING THE GRASS DEFLECTOR
See Figure 5.
Attach the blade guard to the mounting bracket
■
and align the screw holes on the blade guard to the
screws on the mounting bracket.
Using the combination wrench, tighten all two screws
■
securely.
NOTE: When using the string head, the grass deflector
must be attached to the blade guard.
Attach the grass deflector to the blade guard and
■
23
HR ET LT LV SK BG