Led electric fire range with thermostatic remote control (64 pages)
Summary of Contents for Regency E21-NG10
Page 1
E21 Gas Insert Energy ™ Installation Manual www.regency-fire.com MODELS: E21-NG10 Natural Gas E21-LP10 Propane WARNING FIRE OR EXPLOSION HAZARD Failure to follow safety warnings exactly could result in serious injury, death, or property damage. - Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
Page 2
Gas Fireplace Series has been designed to provide you with all the warmth and charm of a ® fireplace, at the flick of a switch. The models E21-NG10 and E21-LP10 of this series have been approved by Warnock Hersey /Intertek for safety. As it also bears our own mark, it promises to provide you with economy, comfort and security for many trouble free years to follow.
Page 3
28-3/16" (715mm) 17-7/16" (442mm) 40-3/16" (1020mm) 36" 11-1/2" (913mm) (291mm) 14-1/4" 24-7/8" (362mm) (631mm) Shown with Low Profile Faceplate Oversize Faceplate Dimensions: 44-1/8" W x 25-3/4" H Regency E21-10 Gas Fireplace Insert ®...
Log Replacement ............29 Glass Gasket ...............29 Door Glass Replacement ..........29 Removing Valve Assembly ..........29 Removing the Fan ............29 Main Assembly ............30 Burner Assembly & Log Set ........31 Low profile faceplate assembly ........31 Warranty ..............35 Regency E21-10 Gas Fireplace Insert ®...
Page 5
This is a copy of the label that accompanies each Regency Gas Insert. We have printed ® a copy of the contents here for your review. The safety label is located on the front inside base of the unit visible when the bottom louver is open.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipm ent, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation. Regency E21-10 Gas Fireplace Insert ®...
SURFACE TEMPERATURES, ESPE- CIALLY THE FIREPLACE GLASS, AND SHOULD STAY AWAY TO AVOID BURNS IF THE BARRIER BECOMES DAMAGED, OR CLOTHING IGNITION. THE BARRIER SHALL BE REPLACED WITH THE MANUFACTURER'S BARRIER FOR THIS APPLIANCE. Regency E21-10 Gas Fireplace Insert ®...
SAVE THESE insert. INSTRUCTIONS 12) Wear gloves and safety glasses for protection while doing required maintenance. The Regency Gas Fireplace must be installed in ® accordance with these instructions. Carefully read 13) Ensure adequate combustion and ventilation air.
REQUIREMENTS FIREPLACES or bottom of the firebox in a proper workmanship like manner. This access hole must be plugged The Regency E21 may be installed and vented ® NOTE: Any parts that are removed must be removed with non-combustible insulation after the gas...
CLEARANCES 1) Locate your appliance. Refer to the "Clear- Diagram shows the minimum fireplace opening ances to Combustibles" and "Minimum required to be able to install the Regency ® Fireplace Clearances" sections. fireplace insert. 2) Make gas and electrical connections. Refer to the "Gas Connection"...
14 inches (356mm). The minimum combustible board. height from the top of the appliance to the ceiling is 36 inches (914mm). *31-1/2" To base of unit * With mantel at 0" to 3-1/2" Regency E21-10 Gas Fireplace Insert ®...
Variable Speed: 127 CFM, thermally Important: Always check for gas leaks activated with a soap and water solution or gas leak detector. Do not use open flame NATURAL GAS E21-NG10 for leak testing. For altitude: 2000 ft - 4500 ft. Burner Inlet Orifice Size: 44 DMS Max.
(grounding) plug for cause improper and dangerous your protection against shock hazard operation. and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug. Regency E21-10 Gas Fireplace Insert ®...
An Offset Flue Adaptor Kit, Part #532-920 is available as an accessory to move the flue outlet back for easier liner installations in deep fireplaces. The offset flue adaptor requires the use of a 3" liner. 14 | Regency E21-10 Gas Fireplace Insert ®...
3) Observe any local code restrictions, if any, The appliance must be isolated from the gas The Regency Insert incorporates its own internal ® regarding the installation of gas inserts. supply piping system by closing its individual...
(see diagram for correct Note: Aeration Adjustment should only be positioning), then the two side panels. Slide performed by an authorized Regency ® the side brick panel into place from the front Installer at the time of installation or of the firebox, there is a tab at the top of the service.
- do not force into position. 2) Spread vermiculite around the fi rebox base. Then take some embers and spread them over the vermiculite as shown. 27-24 Regency E21-10 Gas Fireplace Insert ® 12/17/07 918-673b...
Page 18
27-27 against the 2nd grate post. 27-27 27-25 27-23 6) Fit log 27-26 into the pins on the front right side of the burner. 27-27 27-26 2nd Grate Post 18 | Regency E21-10 Gas Fireplace Insert ® 918-673b 12/17/07...
Page 19
9) Fit the left end of log 27-29 into the pin on the front left side of the burner (in front of the 1st grate post) and rest the right end of log 27-29 onto the notch on log 27-27. 27-24 27-27 27-26 27-29 Notch 1st Grate Post Regency E21-10 Gas Fireplace Insert ® 12/17/07 918-673b...
Page 20
13) Separate platinum embers and place on the burner just in front of the logs. Avoid stacking platinum embers. Completed Log Set Installation 27-28 27-27 27-23 27-24 27-30 27-29 27-26 27-25 20 | Regency E21-10 Gas Fireplace Insert ® 918-673b 12/17/07...
2. Lower screen assembly onto unit, bottom of screen is secured by 2 lower tabs on safety screen onto pins inside unit as shown below. magnets. 3. To remove–reverse steps. Pin in unit Tab on screen assembly Magnet at bottom of screen Regency E21-10 Gas Fireplace Insert ®...
Remove NG Stepper motor and push Burner Tray to the left, and lift off. Also check that the pilot and main burner replace with LP Stepper motor injectors are appropriate for the gas type. 22 | 919-463 10.28.14 Regency E21-10 Gas Fireplace Insert ®...
12 pin connector to receiver from wiring harness (marked receiver). Connect the male end black and red fan switch wires (in the black casing) to the wire connectors from the fan speed control. Faceplate backing Receiver Diagram 4 Diagram 7 Regency E21-10 Gas Fireplace Insert ® 11.05.14 919-462...
Page 24
Final Install Pin in unit Tab on screen assembly Diagram 10 Magnet at bottom of screen 11. Lower screen assembly onto unit, bottom of screen is secured by 2 magnets 24 | Regency E21-10 Gas Fireplace Insert ® 11.05.14 919-462...
32 Ft. on an interior wall. 18 GA. 20 Ft. 20 GA. 12 Ft. Regency offers an optional programmable thermo- 09.24.14 919-455 stat but any 250-750 millivolt rated non-anticipator 22 GA. 9 Ft. type thermostat that is CSA, ULC or UL approved may be used.
FIRST FIRE 3) Check for proper draft. Blower: The first fire in your stove is part of the paint curing Regency gas appliances use high tech blowers ® process. To ensure that the paint is properly cured, to push heated air farther into the room. It is not it is recommended that you burn your fireplace for at unusual for the fan to make a "whirring"...
Diagram 1 5. Press and release the ON/OFF button on the remote handheld transmitter. An audible beep should be heard from the receiver. ON/OFF Button Diagram 2 Remote shown in Manual Mode on Hi Regency E21-10 Gas Fireplace Insert ®...
Do not try to light the pilot by hand. and should only be refinished with heat resist- B) BEFORE OPERATING smell all around the appliance area for gas. Be sure to smell next to the fl oor ant paint (not with wall paint). Regency uses ®...
- see steps 9-12 in "Removing Valve of the body base and pull the thermodisc Assembly. out of the bracket under the left side of the Your Regency stove is supplied with high ® firebox bottom. temperature, 5 mm Neoceram ceramic glass that 7) Remove wires from fan.
Conditions: Any part or parts of this unit which in our judgement show evidence of such defects will be repaired or replaced at Regency's option, through an accredited distributor or agent provid- ed that the defective part be returned to the distributor or agent Transportation Prepaid, if requested.