Step 3: Connecting The Audio Cords/Hdmi Cord; Step 5: Preparing The Remote - Sony RDR-GX350 Service Manual

QQ
3 7 63 1515 0
About the SMARTLINK
features (for SCART
connections only)
If the connected TV (or other connected
equipment such as a set top box) complies
*3
with SMARTLINK, NexTView Link ,
*1 *2
MEGALOGIC , EASYLINK ,
*2 *3
CINEMALINK , Q-Link , EURO VIEW
*4 *5
LINK , or T-V LINK , you can enjoy the
following SMARTLINK features.
• TV Direct Rec. (page 32)
• One-Touch Play (page 61)
• Preset Download
You can download the tuner preset data
from your TV to this recorder, and tune the
recorder according to that data in "Easy
Setup."
• NexTView Download
You can easily set the timer by using the
NexTView Download function on your TV.
To prepare for the SMARTLINK features
Set "LINE 3 Out" to "Video" in the "Video
In/Out" setup (page 115) and
"SMARTLINK" to "This Recorder Only" in
the "Options" setup (page 128).
b
Notes
• For correct SMARTLINK connection, you will
need a SCART cord that has the full 21 pins.
Refer to your TV's instruction manual as well for
this connection.
• Not all TVs respond to the functions above.
*1
"MEGALOGIC" is a registered trademark of
Grundig Corporation.
*2
"EASYLINK" and "CINEMALINK" are
trademarks of Philips Corporation.
*3
"Q-Link" and "NexTView Link" are trademarks
of Panasonic Corporation.
*4
"EURO VIEW LINK" is a trademark of Toshiba
Corporation.
*5
"T-V LINK" is a trademark of JVC Corporation.
TE
L 13942296513
18
B Audio L/R (left/right) input jacks
This connection will use your TV's or audio
component's two speakers for sound.
z Hint
For correct speaker location, see the operating
instructions supplied with the connected
components.
b
Notes
• Do not connect your TV's audio output jacks to
the LINE IN (R-AUDIO-L) jacks at the same
time. This will cause unwanted noise to come
from your TV's speakers.
• With connection B, do not connect the LINE IN
(R-AUDIO-L) and LINE 2 OUT (R-AUDIO-L)
jacks to your TV's audio output jacks at the same
time. This will cause unwanted noise to come
from your TV's speakers.
• With connection A, after you have completed the
connection, make the appropriate settings in the
"Audio Out" setup (page 117). Otherwise, no
sound or a loud noise will come from your
speakers.
• When you connect the recorder to an audio
component using an HDMI cord, you will need to
do one of the following:
– Connect the audio component to the TV with
the HDMI cord, or
– Connect the recorder to the TV with a video
cord other than HDMI cord (component video
cord, S-video cord, or audio/video cord).
*1
Manufactured under license from Dolby
Laboratories.
"Dolby" and the double-D symbol are
trademarks of Dolby Laboratories.
*2
"DTS" and "DTS Digital Out" are registered
trademarks of DTS, Inc.
www
.
20
http://www.xiaoyu163.com
About the HDMI Control
functions for 'BRAVIA' Theatre
Sync (for HDMI connections
only)
By connecting Sony components that are
compatible with the HDMI Control function
with an HDMI cord (not supplied), operation
is simplified as below:
• One-Touch Play (page 61)
• System Power-Off
When you turn the TV off by using the
power button on the TV's remote, the
components compatible with the HDMI
Control function turn off automatically.
To prepare for the 'BRAVIA' Theatre Sync
features
Set "HDMI Control" to "On" in the "HDMI
Output" setup (page 126). For details on TV
settings, refer to the operating instructions
supplied with the TV.
b
Notes
• Depending on the connected component, the
HDMI Control function may not work. Refer to
the operating instructions supplied with the
component.
• The recorder supports only the playback option of
HDMI Control. "Player" appears on the TV
screen when using the HDMI Control functions.
Step 4: Connecting the
Mains Lead
Connect the supplied mains lead to the AC IN
terminal of the recorder. Then plug the
recorder and TV mains leads (AC power
cords) into the mains. After you connect the
mains lead, you must wait for a short
while before operating the recorder.
You can operate the recorder once the front
panel display lights up and the recorder enters
standby mode.
If you connect additional equipment to this
recorder (page 26), be sure to connect the
mains lead after all connections are complete.
1
to AC IN
2
to mains
x ao
y
i
http://www.xiaoyu163.com
8

Step 3: Connecting the Audio Cords/HDMI Cord

Select one of the following patterns, A or B, according to the input jack on your TV monitor,
projector, or audio component such as an AV amplifier (receiver). This will enable you to listen
to sound.
[Speakers]
Rear (L)
Front (L)
Centre
HDMI cord
(not supplied)
to HDMI OUT
to LINE 2 OUT (R-AUDIO-L)
(white)
(red)
(yellow)*
: Signal flow
* The yellow plug is used for video signals (page 16).
A Digital audio input jack
If your audio component has a Dolby
*2
Digital, DTS , or MPEG audio decoder and
a digital input jack, use this connection. You
can enjoy Dolby Digital (5.1ch), DTS
Q Q
(5.1ch), and MPEG audio (5.1ch) surround
3 6 7 1 3
effects.
Step 5: Preparing the
Remote
You can control the recorder using the
supplied remote. Insert two R6 (size AA)
batteries by matching the 3 and # ends on
the batteries to the markings inside the
battery compartment. When using the
remote, point it at the remote sensor
recorder.
b
Notes
• If the supplied remote interferes with your other
Sony DVD recorder or player, change the
command mode number for this recorder
(page 22).
• Use the batteries correctly to avoid possible
leakage and corrosion. Should leakage occur, do
not touch the liquid with bare hands. Observe the
following:
– Do not use a new battery with an old battery, or
batteries of different manufacturers.
– Do not attempt to recharge the batteries.
– If you do not intend to use the remote for an
extended period of time, remove the batteries.
– If battery leakage occurs, wipe out any liquid
inside the battery compartment, and insert new
batteries.
• Do not expose the remote sensor (marked
the front panel) to strong light, such as direct
sunlight or a lighting apparatus. The recorder may
not respond to the remote.
• When you replace the batteries of the remote, the
code number and Command Mode may be reset
to the default setting. Set the appropriate code
number and Command Mode again.
u163
.
1-4
2 9 9 4 2 8
[Speakers]
A
Rear (R)
Audio component with
a decoder
Front (R)
Subwoofer
or to coaxial/HDMI digital input
Coaxial digital cord
(not supplied)
to DIGITAL OUT (COAXIAL)
DVD recorder
B
INPUT
VIDEO
(yellow)
L
(white)
AUDIO
Audio/video cord
R
(not supplied)
(red)
TV, projector, or
audio component
If you connect a Sony audio component that
*1
is compatible with the HDMI control
function, refer to the operating instructions
supplied with the audio component.
1 5 0 5 8 2 9 9 4
,continued
Controlling TVs with the
remote
You can adjust the remote's signal to control
your TV.
b
Notes
• Depending on the connected unit, you may not be
able to control your TV with some or all of the
buttons below.
on the
• If you enter a new code number, the code number
previously entered will be erased.
Number
buttons
TV/DVD
DISPLAY
x
TV [/1
TV 2 +/–
TV t
TV PROG
+/–
1
Hold down TV [/1 located at the
bottom of the remote.
Do not press the [/1 button at the top of
the remote.
on
2
With TV [/1 pressed down, enter the
TV's manufacturer code using the
number buttons.
For instance, to enter "09," press "0" then
m
"9." After you enter the last number,
release the TV [/1 button.
co
,continued
9 9
2 8 9 9
19
21