Assembly 組裝說明; Device Connection 設備連接說明 - THUNDER TIGER Raptor E550S Instruction Manual

ASSEMBLY 組裝說明
The detailed assembly steps are shown from page 26 to 29.
詳細組裝圖請參考第13~24頁。
Assemble in right order
依標示順序組裝
Tail Pulley
Tail
尾惰輪
機尾
Belt
皮帶
Rotate the belt 90°
counterclockwise.
反時針方向旋轉皮帶90°
DEVICE CONNECTION 設備連接說明
The wire connection between devices and receiver may differ in different brand of radio system. The figures below are for your
reference, please read your radio system manual to find the proper connections.
各品牌遙控系統的電子設備與接收機間接線方法或有差異，以下圖示為安裝範例，實際接線方式請參閱您的遙控器說明書。
JR / SPECTRUM
Servo Cable 連接線
Gain Wire 訊號線
AUX1(CH6) / CH2*
CH2 / AUX1(CH6)*
Pitch螺距 Aileron左右/副翼
Battery of
receiver
4.8-5.8V
接收器電池
7 channel receiver
4.8-5.8V
七動作接收器
Although he Speed Controller (ESC) comes with the ARF featuring a 5V BEC, to connect an additional receiver battery
pack to avoid any unexpected shutdown of BEC for in case is recommended.
To go through the following setting processes, you could just connect the receiver battery to receiver to active the servos
and gyro instead of connecting the Lipo battery pack to ESC.
完成機內附電子調速器具備BEC功能，但仍建議您額外使用一顆接收機電池以防止BEC意外斷電的情況。（BEC safe措施）
進行接下來的設定作業，您可只連接接收機電池來啟用伺服機與陀螺儀，而不必連接鋰電池組至電子調速器
BELT INSTALLATION
2
傳動皮帶安裝
Guide Pulley
主惰輪
Autorotation Tail
Drive Pulley
尾驅動輪
Nose
機首
3
*CH2 & Aux1(CH6) are
Interchangeable
*CH2 & Aux1(CH6) 可互換
ESC速控器 Elevator前後/升降舵 Rudder尾舵
Gyro
陀螺儀
1
(1) Insert the tail boom into the boom bracket and push it all the way to
the end.
將尾管穿入尾管固定座內並推到底。
(2) Warp the belt onto the autorotation tail drive pulley; note the belt
direction of rotation when warping.
將皮帶繞過尾驅動輪；注意安裝時皮帶的扭轉方向。
(3) Gently pull back the tail boom until the tension of the belt allows no
more than 5 mm (3/16") of free play in the belt.
慢慢地將尾管向後拉緊，直至按壓皮帶時，間隙小於5 mm (3/16") 為最佳。
(4) Move the tail boom supports bracket and metal clip to their proper
positions, and then tighten the screws to avoid unexpected
invagination of tail boom.
將尾管支撐架及止擋環定位，並鎖緊螺絲，以防止尾管內鏥。
(5) Secure all other screws tightly and mount the blades.
鎖固所有的其他螺絲並安裝上旋翼。
ACE RC / FUTABA / HITEC
Servo Cable 連接線
Gain Wire 訊號線
CH6 / CH1*
Pitch螺距 Elevator前後/升降舵
Battery of
receiver
4.8-5.8V
接收器電池
7 channel receiver
7 channel receiver
4.8-5.8V
七動作接收器 七動作接收器
-5-
CH2
CH1 / CH6*
Aileron左右/副翼 ESC速控器
*CH1 & CH6 are
Interchangeable
*CH1 & CH6 可互換
Rudder尾舵
Gyro
陀螺儀