Murray 405000x8B Instruction Book

Murray lawn tractor instruction book
Table of Contents

Advertisement

MODEL
405000x8B
BUILT IN THE
F–030745L

Advertisement

Table of Contents
loading

Summary of Contents for Murray 405000x8B

  • Page 1 MODEL 405000x8B BUILT IN THE F–030745L...
  • Page 2: Table Of Contents

    For assistance in making such adjustments, consult your Instruction Book. To make a claim under this Murray, Inc. Two (2) Year Limited Warranty, return the unit (or if authorized in advance, the defective part) along with your proof of purchase to an Authorized Service Center near you. To locate the nearest Authorized Service Center, call the Central Parts Distributor for your area shown in the list provided with your unit or check the Yellow Page listings in your local telephone directory.
  • Page 3: Responsibility Of The Owner

    This instruction book is for several different models. The instructions are written for a person with some mechanical ability. Like most ser- vice books, not all the steps are described. Steps on how to loosen or tighten fasteners are steps anyone can follow with some mechanical ability.
  • Page 4 b. Limit loads to those you can safely control. c. Do not turn sharply. Use care when backing. d. Use counterweights or wheel weights when suggested in the Instruction Book. 19. Do not operate this machine if you are taking drugs or other medication which can cause drowsiness or affect your ability to operate this machine.
  • Page 5: Safe Mowing Guide

    Each person that operates power equipment must learn to use correct and safe mowing procedures. To help you learn, carefully read the following pages. Most of the time the operator was not correctly shown or did not read the instructions on the unit or in the Instruction Book before using the unit.
  • Page 6 mower was completely assembled at the store, you must still check the mower according to the assembly instructions. Make sure the mower is correctly assembled and that all fasteners are tight. Make sure the engine has the correct amount of oil. Check these items often during the life of the mower.
  • Page 7 Also, the grass bagger will function better when the engine is operating at maximum speed. On slopes, decrease the ground speed and use care making sure the mower feels safe to operate. If the weather conditions are bad, do not mow.
  • Page 8: Steps To Follow

    BEFORE MOWING F Be sure to dress correctly. Wear hard shoes, not sandals or tennis shoes. F Examine the blade. A blade that is bent, cracked, or damaged must be replaced with a factory replacement blade. F Fill the fuel tank outside. Clean off spilled fuel. F Read and follow the Owner’s Manual, the instructions with the engine, and the instructions with any attachments.
  • Page 9: International Pictorials

    INTERNATIONAL PICTORIALS INTERNATIONAL PICTORIALS IMPORTANT: Some of the following pic- torials are located on your unit or on literature supplied with the product. Be- fore you operate the unit, learn and un- derstand the purpose for each pictorial. Safety Warning Pictorials Warning Shield Eyes.
  • Page 10: Assembly

    ASSEMBLY Read and follow the assembly and adjustment instructions for your mower. All fasteners are in the parts bag. Do not discard any parts or material until the unit is assembled. NOTE: In this instruction book, left and right describe the loca- tion of a part with the operator on the seat.
  • Page 11: How To Install The Seat

    HOW TO INSTALL THE SEAT Carefully remove the plastic bag from the seat. Use the fasteners shown below to install the seat. The fasteners are shown at full size. 1001054 NOTE: Fasteners may be attached to seat for shipping purposes, if so remove fasteners before proceeding. Align the holes in the seat hinge to the holes in the seat (Figure 1).
  • Page 12: Maintenance Free Battery

    MAINTENANCE FREE BATTERY IMPORTANT: Before you attach the battery cables to the battery, check the battery date. The battery date tells if the battery must be charged. Check the top of the battery for the location of the battery date (Figure 3).
  • Page 13: Important! Before You Start Mowing

    IMPORTANT! BEFORE YOU START MOWING - Check the engine oil. - Fill the fuel tank with gasoline. - Check the level of the mower housing. - Check the air pressure of the tires. - Make sure the battery cables are attached. HOW TO PREPARE THE ENGINE NOTE: The engine was shipped from the factory filled with oil.
  • Page 14: Operation

    Throttle Control Lever Clutch / Brake Pedal Lift Lever BLADE ROTATION CONTROL: control to start and stop the rotation of the blade. CLUTCH / BRAKE PEDAL: The first function is a clutch. The second function is a brake. HEADLIGHT SWITCH: The headlight switch is the first part of the ignition switch.
  • Page 15: Attachments

    ATTACHMENTS This unit can use many different attachments. See the attachment page in this book. This unit can pull attachments like a lawn sweeper, a lawn aerator, a hopper spreader or a small trailer. This unit can not use attachments that engage the ground like a plow, a disk harrow, or a cultivator.
  • Page 16: How To Set The Parking Brake

    HOW TO SET THE PARKING BRAKE Completely push the clutch/brake pedal forward. Lift the parking brake lever (Figure 6). Remove your foot from the clutch/brake pedal and then release the parking brake lever. Make sure the parking brake will hold the unit.
  • Page 17: How To Operate With The Mower Housing

    WARNING: The deflector is a safety device. Do not re- move the deflector. The deflector forces the dis- charged material toward the ground. Always keep the deflector in the down position. If the deflector is dam- aged, replace the deflector with an original equipment part from an authorized service center.
  • Page 18: Before Starting The Engine

    BEFORE STARTING THE ENGINE CHECK THE OIL NOTE: The engine was shipped from the factory filled with oil. Check the level of the oil. Add oil as needed. See the engine manufacturer’s instructions for the type of gasoline and oil to use.
  • Page 19: Operating Tips

    OPERATING TIPS Check the blade rotation control for correct adjustment. For the blade(s) to disengage correctly, the adjustment must be cor- rect. Before you use the unit, check the oil in the engine and add oil if necessary. If the engine will not start, first make sure the wire is attached to the spark plug.
  • Page 20: Maintenance

    Blade, Inspect and Sharpen Blade Rotation Control, Check Brake, Check Clutch, Check Tires, Check Battery, Check and Charge Battery, Clean Lubrication * Dusty conditions every 25 hours. GENERAL RECOMMENDATIONS The owner’s responsibility is to maintain this product. This will extend the life of the product and is also necessary to maintain warranty coverage.
  • Page 21: How To Remove And Install The Blade

    INSPECT BLADE WARNING: Before you inspect or remove the blade, disconnect the wire to the spark plug. If the blade hits an object, stop the engine. Check the unit for dam- age. The blade has sharp edges. When you hold the blade, use gloves or cloth material to protect your hands.
  • Page 22: How To Adjust The Blade Rotation Control

    WARNING: To prevent an injury, the blade rotation control must operate correctly. In normal usage, the blade rotation control will not require an adjustment. However, if the cutting performance decreases or the quality of cut is poor, make the following changes. When you mow, make sure the throttle control in in the FAST position.
  • Page 23: How To Check And Adjust The Drive Brake

    Completely push the clutch/brake pedal forward. Set the parking brake. Move the shift lever to the neutral (N) position. Push the unit. If the rear wheels rotate, adjust or replace the brake pads. Adjust the drive brake as follows. The location of the drive brake is on the right side of the gearbox (Figure 15).
  • Page 24: How To Adjust The Shift Lever

    HOW TO ADJUST THE SHIFT LEVER If the NEUTRAL position on the shift lever does not match neutral on the gearbox, adjust the shift lever as follows. Stop the engine. Disconnect the adjuster nut from the shifter bracket (Figure 17). Make sure the shift lever is in the NEUTRAL position.
  • Page 25: Where To Lubricate

    WHERE TO LUBRICATE Apply grease with a brush to the areas shown. Lubricate the areas shown with engine oil. NOTE: Apply grease to the steering gear assembly. CAUTION: If the unit is operated in dry areas that have sand, use a dry graphite spray to lubricate the unit. HOW TO CHECK THE FUEL FILTER NOTE: Before you replace the fuel filter or the fuel line, the fuel tank must be empty.
  • Page 26: How To Remove The Mower Housing

    HOW TO REMOVE THE MOWER HOUSING Move the blade rotation control to the DISENGAGE position. Move the lift lever to the level adjustment position (Figure 21). WARNING: The lift lever is spring loaded. Make sure the lift lever is locked in the LEVEL ADJUST- MENT position.
  • Page 27: How To Level The Mower Housing

    HOW TO LEVEL THE MOWER HOUSING If the mower housing is level, the blade will cut easier and the lawn will look better. WARNING: Before you make an inspection, adjust- ment, or repair to the unit, disconnect the wire to the spark plug.
  • Page 28: How To Replace The Motion Drive Belt

    HOW TO REPLACE THE MOTION DRIVE BELT REMOVAL Remove the mower housing. See the instructions on “How To Remove The Mower Housing”. Completely push the pedal forward and engage the parking brake. Remove the idler pulley (Figure 26). Motion Drive Belt Idler Pulley Loosen The Belt Guides...
  • Page 29 INSTALLATION Slide the motion drive belt between the stack pulley and the belt guides (Figure 29). Install the motion drive belt on the top pulley of the stack pulley. Make sure the “V” side of the belt is against the pulley. Push the motion drive belt through the opening between the steering plate and the engine plate.
  • Page 30: How To Replace The Mower Drive Belt

    HOW TO REPLACE THE MOWER DRIVE BELT Remove the mower housing. See the instructions on “How To Remove The Mower Housing”. Pull the belt retainer away from the idler pulley and remove the mower drive belt (Figure 32). Pull the belt retainer away from the right mandrel pulley and remove the mower drive belt.
  • Page 31: How To Install The Wheels

    HOW TO INSTALL THE WHEELS If the wheels must be removed for service, make sure they are installed as follows. Front Wheel Make sure the valve stem is to the outside of the tractor. Slide the front wheel on the spindle (See Figure 33). Fasten the front wheel with washer and cotter pin.
  • Page 32: How To Replace The Fuse

    HOW TO REPLACE THE FUSE If the fuse is blown, the engine will not start. The location of the fuse is next to the battery. Remove the fuse and replace with a automotive fuse (Figure 35). HOW TO REPLACE THE LIGHT BULB Raise the tractor hood.
  • Page 33: Trouble Shooting Chart

    TROUBLE SHOOTING CHART PROBLEM: The engine will not start. Follow the steps, “How To Start The Engine” in this book. Electric–Start Models: Clean the battery terminals. Tighten the cables. Drain the fuel tank. Clean the fuel line. Replace the fuel filter. Remove the spark plug(s).
  • Page 34: How To Order Repair Parts

    F–030745L...
  • Page 35 NOTES F–030745L...
  • Page 36 F–030745L CHASSIS & HOOD...
  • Page 37: Parts List

    Description Seat Cap, Push 0n Spring Screw Bolt, Wing Washer Bolt, Shoulder Support, Seat Rod, Pivot Bracket, Pivot Bolt Bolt, Shoulder Washer Spring Screw Screw Spring Deck, Seat Plate, Index Screw Mat, Left Mat, Right Hood Grille Lens, Left Housing, Left Headlamp Lens, Right F–030745L Part No.
  • Page 38: Motion Drive

    F–030745L MOTION DRIVE...
  • Page 39 Description Bolt, Shoulder Nut, Hex Arm, Idler Rod, Clutch Washer Grip Pin, Cotter Lever, Shift Washer Link, Shift Nut, Adjuster Grip Rod, Parking Brake Nut, Adjuster Bracket, Shift Pivot Screw Mount, Stud Spring Bolt, Shoulder Spring, Extension Bracket, Right Shifter Frame, Right Bolt, Carriage Frame, Left...
  • Page 40 F–030745L STEERING...
  • Page 41 Description Wheel, Steering Post, Steering Cap, Steering Wheel Bearing ** Nut, Flange Bolt, Shoulder Gear, Pinion ** Ring, Snap ** Gear, Sector Bearing Bolt Plate, Steering Plate, Engine Nut, Flange Nut, Flange Bracket, Hanger Axle, Hanger Bolt Pin, Cotter Bearing Spindle Assembly, Left Bolt When you order a tire, make sure to give the brand name of the tire so that the tread pattern on the tire will match.
  • Page 42: Mower Housing Suspension

    F–030745L MOWER HOUSING SUSPENSION...
  • Page 43 Description Grip Handle Pad, Switch Bolt Grip Spring Washer Handle, Lift Lever, PTO Bolt, Shoulder Pin, Cotter Washer Link, PTO Nut, Flange Screw Spring Bracket, PTO Spring Crank, PTO Link, Lift Link, Lift Handle F–030745L MOWER HOUSING SUSPENSION Part No. 092698 Washer 094157 Z...
  • Page 44: Mower Housing

    F–030745L MOWER HOUSING 5 47...
  • Page 45 Description Pulley, Jackshaft Nut, Hex Belt, Mower Drive Pulley, Idler Nut, Flange Spacer, Pulley Link, Lift Pad, Friction Bolt, Shoulder Bracket, Suspension Pad Assembly, Left Brake Knob Bolt, Shoulder Plate, Suspension Spring Nut, Flange Bracket, Suspension Pin, Hanger Washer Pin, Cotter Bolt Cover, Pulley Bolt, Shoulder...
  • Page 46 MODEL 405000x8B REPAIR PARTS ENGINE MOUNT F–030745L...
  • Page 47 Parts are available from a Briggs & Stratton Authorized Service Center. See “Engines, Gasoline” or “Gasoline Engines” in the yellow pages of the telephone directory. These parts are included when ordering Key number 2. F–030745L Description Fuel Cap ** Fuel Tank Hose Clamp ** Fuel Line (Must cut to length) ** Hose Clamp **...
  • Page 48 MODEL 405000x8B REPAIR PARTS ELECTRICAL SYSTEM F–030745L...
  • Page 49: Electrical System

    F–030745L Description Harness, Light Wire Socket, Light Bulb, Light Harness, Chassis Wire Switch, Ignition Key, Ignition Nut, Hex Cap, Ignition Switch, Limit Fuse Holder, Fuse Solenoid Screw, Mounting Locknut Cable, Battery Ground Screw, Ground Cable Battery Bolt, Carriage Wingnut Harness, Seat Switch Wire Switch, Seat Sensor Cable ELECTRICAL SYSTEM...
  • Page 50: Slope Guide

    F–030745L...
  • Page 51: Index

    Adjustments Blade Rotation Control, 22 Clutch, 23 Drive Brake, 23 Mower Housing, Level, 27 Shift Lever, 24 Attachments, 15, 52 Battery Charge, 24 Check, 12 Clean, 24 Install, 12 Removal, 24 Storage, 32 Belt Motion Drive Adjust, 23 Replace, 28 Mower Drive Adjust, 22 Replace, 30...
  • Page 52: Lawn Tractor Accessories

    LAWN TRACTOR ACCESSORIES Make your Lawn Tractor do more than you ever imagined. The accessories shown on this page can be used on your Lawn Tractor. See the Store or Dealer where you purchased your Lawn Tractor. If you are unable to obtain the necessary information, contact the Central Parts Distribution Center for your area as listed in your Repair Parts Book.

Table of Contents