Sanyo PLC-WM5500 Service Manual page 57

Electrical Adjustment
Grp / No. Item
18 Temp B Warning Normal Highland Temp B (Lamp) to judge the Temp Error at Normal/Highland
19 Temp CB Warning Normal Hiland
20 Temp A Warning Eco Highland
21 Temp B Warning Eco Highland
22 Temp C Warning Eco Hilghand
260 Auto Calibration (Common)
0 Execute Calibration
1 Loop Count
2 Auto Status
3 AutoWait
4 CHECK - Tolerance
5 Time out wait
261 Auto Calibration (RGB)
0 OFFSET AREA H START
1 OFFSET AREA V START
2 GAIN AREA H START
3 GAIN AREA V START
4 Image AREA H WIDTH
5 Image AREA V HEIGHT
6 OFFSET Target
7 OFFSET Tolerance
8 GAIN Target
9 GAIN Tolerance
10 Image Level Tolerance
262 Auto Calibration (CVBS/SVIDEO) PW392-AFE MDL <10bits>
0 Y Image Area Start X
1 Y Image Area Start Y
6 Image Area H WIDTH
7 Image Area V HEIGHT
8 Y Target Level
11 Gain Tolerance
12 Image Level Tolerance
264 Auto Calibration (YCbCr)
0 Y-OFFSET AREA H START
1 Y-OFFSET AREA V START
2 CB - OFFSET AREA H START
3 CB - OFFSET AREA V START
4 CR - OFFSET AREA H START
5 CR - OFFSET AREA V START
6 Y - GAIN AREA H START
7 Y - GAIN AREA V START
8 CB - GAIN AREA H START
9 CB - GAIN AREA V START
10 CR - GAIN AREA H START
11 CR - GAIN AREA V START
12 Image AREA H WIDTH
13 Image AREA V HEIGHT
14 Y - OFFSET TARGET
15 CB OFFSET TARGET
16 CR OFFSET TARGET
17 Y - GAIN TARGET
18 CB - GAIN TARGET
19 CR - GAIN TARGET
20 OFFSET Tolerance
21 GAIN Tolerance
22 Image Level Tolerance
280 AutoPC Adjsut
0 AutoPCAdjustEnable
1 Frequency Step
2 Frequency Threshold
3 Fine Phase
Function
Temp C (Panel) to judge the Temp Error at Normal/Highland
Temp A (Room) to judge the Temp Error at Eco/Highland
Temp B (Lamp) to judge the Temp Error at Eco/Highland
Temp C (Panel) to judge the Temp Error at Eco/Highland
Execute Calibration when the Value is changed. (For PC White
100%)
Max Times of Calibration
Calibration Log (Read only)
0: Calibration End Correctly 1: On Adjusting 9: Calibration
Error
Waiting time
Tolerance of Offset
Wait Time until Time out [sec.]
PW392-AFE MDL <10bits>
Black Level Acq. Area H Start
Black Level Acq. Area V Start
White Level Acq. Area H Start
White Level Acq. Area V Start
Black/White Level Area Width
Black/White Level Area Height
Black Level Adj target
Black Level Adj telerance
White Level Adj target
White Level Adj telerance
Acq. Image Level Adj Tolerance
Y Image Area H Start
Y Image Area V Start
Image Level Acq. Width
Image Level Acq. Height
Y Level Adj target
Level Adj Tolerance
Acq. Image Level Adj Tolerance
PW392-AFE MDL <10bits>
Y - Offset Acq Area H Start
Y - Offset Acq Area V Start
CB - Offset Acq. Area H Start
CB - Offset Acq. Area V Start
CR - Offset Acq. Area H Start
CR - Offset Acq. Area V Start
YCBCR Level Acq. Width
YCBCR Level Acq. Height
OFFSET Adj Tolerance
GAIN Adj Tolerance
Acq. Image Level Adj Tolerance
Auto PC Operation with the un-supported signal in.
0: Enable 1: Disable
TotalDot Search Step
TotalDot Match
Phase after Total Dot Adj.
0: Fine Phase Execute 1: Fine Phase Not Execute
Range
0 - 100
0 - 100
0 - 100
0 - 100
0 - 100
0 - 1
1 - 30
0 / 1 / 9
1 - 20
1 - 255
1 - 255
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 4095
0 - 4095
0 - 1023
1 - 1023
0 - 1023
1 - 1023
1 - 255
0 - 1000
0 - 1000
0 - 4095
0 - 4095
0 - 1023
1 - 255
1 - 255
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 4095
0 - 4095
0 - 1023
0 - 1023
0 - 1023
0 - 1023
0 - 1023
0 - 1023
1 - 255
1 - 255
1 - 255
0 - 1
0-3
0 - 10
0 - 1
-57-
Initial Note
73
67
48
71
65
* Auto calibration
0
8
0
3
4
20
975
500
25
500
13
9
20
1
955
1
8
20
200
8
9
875
1
2
925
500
925
500
925
500
50
500
800
500
700
500
13
9
4
512
512
810
894
894
1
1
8
0
1
5
1