Service Adjustment Data Table - Sanyo PLC-WM5500 Service Manual

Electrical Adjustment

Service Adjustment Data Table

Grp / No. Item
0 AD Converter (PW392)
3 ADC G-GAIN
4 ADC R-GAIN
5 ADC B-GAIN
10 SOGTH
11 SOGHYSDIS
12 HS1TH
13 HS0TH
10 AD Converter (ISL98001)
3 ADC G-GAIN
4 ADC R-GAIN
5 ADC B-GAIN
20 Video Decoder
0 Y Level
1 C Level
10 XCXL Parameter
11 Sync Amp Low
12 Sync Amp High
13 Luma Setup Enable
14 Anti-Alias Filter
15 Anti-Alias Downsample
16 Anti-Alias High Frequency
Comb 3D Cross-Luma Top/Bottom
20
Amplitude
40 General
0 IP Mode
1 3:2 PullDown Mode
2 Detect Film Mode Enable
3 NR Enable for Analog YUV
4 NR Enable for Digital YUV
41 Deinterlacer setting
0 Motion Adaptive Weight Value
1 Angle Interpolation Level
2 CUE Low Pass Filter Enable
42 Deinterlacer setting
0 Motion Adaptive Weight Value
1 Angle Interpolation Level
2 CUE Low Pass Filter Enable
47 Noise Reduction (time)
0 Noise Pixel Range
1 Noise Region 0
2 Noise Region 1
3 Noise Region 2
4 Noise Gain Level
49 Noise Reduction (time)
0 Noise Pixel Range
Function
YCbCr 480i (575i) / YCbCr 480p (575p) /
YCbCr 720p (720p50) / YCbCr 1080i (1035i, 1080i50) /
SCART
PC/YCbCr 480i (575i) / YCbCr 480p (575p) / YCbCr 720p
(720p50) / YCbCr 1080i (1035i, 1080i50) / SCART
PC/YCbCr 480i (575i) / YCbCr 480p (575p) / YCbCr 720p
(720p50) / YCbCr 1080i (1035i, 1080i50) / SCART
RGB/COMPONENT / SCART
RGBCOMPONENT / SCART
H Sync1 Threshold RGB/COMPONENT / SCART
H Sync0 Threshold RGB/COMPONENT / SCART
PC/YCbCr 480i (575i) / YCbCr 480p (575p) / YCbCr 720p
(720p50) / YCbCr 1080i (1035i, 1080i50)
PC/YCbCr 480i (575i) / YCbCr 480p (575p) / YCbCr 720p
(720p50) / YCbCr 1080i (1035i, 1080i50)
PC/YCbCr 480i (575i) / YCbCr 480p (575p) / YCbCr 720p
(720p50) / YCbCr 1080i (1035i, 1080i50)
Composite 60Hz/ S-Video 60Hz/ Composite 50Hz / S-Video
50Hz- Y Level (ADC RGB Gain)
Composite 60Hz / S-Video 60Hz / Composite 50Hz / S-Video
50Hz - C Level (ADC Saturation)
XCXL Level
Minimum sync amplitude threshold for HLOCK 1 to 0 transition
Minimum sync amplitude threshold for HLOCK 0 to 1 transition
7.5IRE Mode (NTSC only)
Anti-Alias Filter
Anti-Alias Downsample
Anti-Alias High Frequency
for PAL/SECAM only
Set at IP OFF 0: Not used IP Block 1: Used IP Block and IP OFF
bit0: Global Motion bit1: Video Motion
0: 2:3pull down & 2:2pull down 1: 2:3pull down 2: 2:2pull down
0 : Noise Reduction detected with Y and UV motion 1 : Noise
Reduction detected with Y motion
Analog YUV : PC/Video/S-Video/Component
Digital YUV : HDMI
<NSYUVEN>
Progressive Mode1, Film Parameter
<KDEINT>
0 : Conservative <====> 4 : Aggressive
<CUELPFEN>
Progressive Mode2 Parameter
<KDEINT>
0 : Conservative <====> 4 : Aggressive
<CUELPFEN>
NR L1 Parameter
<NSRANGEY> / <NSRANGEUV>
<NSREGIONY0> / <NSREGIONUV0>
<NSREGIONY1> / <NSREGIONUV1>
<NSREGIONY2> / <NSREGIONUV2>
<NSFILTERY**> / <NSFILTERUV**>
<NSRANGEY> / <NSRANGEUV>
These initial values are the reference data written from the
CPU ROM to memory IC when replaced new memory IC. The
adjustment items indicated with "✻" are required to readjust fol-
lowing to the "Electrical adjustments". Other items should be
used with the initial data value.
Range
0 - 1023
0 - 1023
0 - 1023
0 - 15
0 - 1
0 - 15
0 - 15
0 - 1023
0 - 1023
0 - 1023
0 - 1023
0 - 1023
0 - 4
0 - 9999
0 - 9999
0 - 1
0 - 7
0 - 3
0 - 3
0 - 3
0 - 1
1 - 3
0 - 2
0 - 1
0 - 1
0 - 255
0 - 5
0 - 255
0 - 255
0 - 5
0 - 255
0 - 2
0 - 1023
0 - 1023
0 - 1023
0 - 255
0 - 2
-46-
Initial Note
(265)/200/210/ 210/210/265 * ( ) not effective
(265)/205/210/ 210/210/265 * ( ) not effective
(265)/205/210/ 210/210/255 * ( ) not effective
(2)/4 / 4 * ( ) not effective
(1)/1 / 0 * ( ) not effective
(4)/4 / 4 * ( ) not effective
(4)/4 / 4 * ( ) not effective
290/(170/185/200/200) * ( ) not effective
290/(140/165/165/165) * ( ) not effective
290/(140/165/165/165) * ( ) not effective
175/175/185/185
405/405/440/440
2
1792
4096
0
4
0
3
3
1
1
0
1
0
30/30/30
4/4/4
0/0/0
0/0/0
2/2/2
0/0/0
1
12
24
40
100
1