Function Keys - DSC PC1555 CP-01 Installation Manual

[*] [6] User Functions
To program user functions, perform the following:
1. Press [*] [6] [Master Code]. The keypad will flash the
'Program' light.
2. Press the number [1] to [6] for the item to be pro-
grammed.
• [1] - Time and Date [1] - Time and Date [1] - Time and Date [1] - Time and Date
See the Power Series User Guide for instructions on
setting the time and date ('Setting the Time and Date').
• [2] - Auto-arm Enable/Disable [2] - Auto-arm Enable/Disable
[2] - Auto-arm Enable/Disable [2] - Auto-arm Enable/Disable
Enter [2] to enable (three keypad beeps) or disable (one
long beep) the auto-arm feature.
• [3] - Auto-arm Schedule [3] - Auto-arm Schedule [3] - Auto-arm Schedule [3] - Auto-arm Schedule
Enter [3] to change the auto-arm time for each day of
the week.
Scroll to the day of the week you want to change, or
enter the number of the day (1-7 for Sunday to Satur-
day). On an LED keypad, zone lights 1-7 will represent
Sunday to Saturday.
When you have selected a day, enter the auto-arm time
in 24-hr format (i.e., enter a 4-digit number in [hhmm]
format).
The system will return you to the day selection menu.
Scroll to the next day you want to program, or to exit
auto-arm programming, press [#].
NOTE: Only PKP-LCD v2.0 or greater keypads support the
[*][6][3] menu option.
• [4] - System Test [4] - System Test [4] - System Test [4] - System Test
When [4] is pressed the panel will perform the following.
- sound the alarm output for two seconds
- light all lights and display pixels on the keypad
- sound the keypad buzzer for two seconds
- test the main panel/PC5200/PC5204 battery
- send a System Test Reporting code, if programmed.
For step-by-step instructions on performing a system test,
see the Power Series User's Guide ('Full System Test').
• [5] - Enable DLS (Downloading) [5] - Enable DLS (Downloading) [5] - Enable DLS (Downloading) [5] - Enable DLS (Downloading)
When [5] is pressed the panel will turn on the down-
loading option for 6 hours. During this time the panel
will answer incoming downloading calls (see Section
5.7 Downloading Options PWS Sect 7)
• • • • [6] – User-initiated Call-Up [6] – User-initiated Call-Up [6] – User-initiated Call-Up [6] – User-initiated Call-Up
When [6] is pressed, the panel will initiate a call to the
downloading computer.
LCD Keypad User Functions
Additional features are available using on the LCD key-
pad. These features do not have numbers assigned. Use
the arrow keys (< >) to scroll through the [
✱
and press the [ ] key to select the following commands.
View Event Buffer: The 256 event buffer can be viewed View Event Buffer
View Event Buffer View Event Buffer
through any LCD keypad.
• Brightness Control Brightness Control: When this option is selected the Brightness Control Brightness Control
keypad will allow you to scroll through 10 different
backlight level options. Use the arrow keys (<>) to
scroll to the desired backlight level and press the [#]
key to exit.
• Contrast Control Contrast Control Contrast Control Contrast Control: When this option is selected the key-
pad will allow you to scroll through 10 different con-
trast level options. Use the arrow keys (<>) to scroll to
the desired contrast level and press the [#] key to exit.
• Keypad Buzzer Control: Keypad Buzzer Control: When this option is selected Keypad Buzzer Control: Keypad Buzzer Control:
the keypad will allow you to scroll through 21 different
keypad sounder tone options. Use the arrow keys (<>)
to scroll to the desired keypad beeper level and press
the [#] key to exit. This function can be achieved on
LED keypads by holding the [*] key.
[*] [7] Command Output Functions
There are four output functions available to the user.
Entering [*] [7] [1-4] [Access Code, if required] will acti-
vate any output programmed for options [19]-[22]
(respectively). Each function can be performed when the
system is either armed or disarmed.
For more information regarding these output types, ( see
Section 5.8 Programmable Output Programming).
[*] [8] Installer Programming
Enter [*][8] followed by the Installer Code to enter
Installer Programming.
[*] [9] Arming Without Entry Delay
When the system is armed with the [*][9] command the
panel will remove the entry delay. After the Exit Delay,
Delay 1 and Delay 2 type zones will be instant and Stay/
Away zones will remain bypassed. ( see section 'Basic Pro-
gramming PWS Sect 3' ).
For more information regarding this feature, see the Pow-
erSeries User's Guide .
The entry delay can be activated or deactivated at any
time while the system is armed by pressing [*][9].
NOTE:
even if the system is armed using [*][9].
[*] [0] Quick Arm
If the Quick Arm Enable
be armed by entering [*][0]. This is a useful method of
arming when someone without an access code will be
required to arm.
[*] [0]
Quick Exit will allow someone to leave an armed premise
through a Delay type zone without having to disarm and
rearm the system.
When [*][0] is entered, if the Quick Exit Enabled option is
enabled, the panel will provide a 2-minute window to
exit. During this time the panel will ignore the first activa-
tion of a Delay type zone. When the Delay zone is secured
the panel will end the 2-minute time period.
If a second Delay zone is tripped, or if the zone is not
restored after two minutes, the panel will start entry
delay.
Quick Arm Enable . . . . . . . . . . . . . . . . . . Section [015], Option [4]
Quick Exit Enable . . . . . . . . . . . . . . . . . . . Section [015], Option [3]

4.3 Function Keys

There are five function keys on the PC1555 CP-01 key-
pads labelled Stay, Away, Chime, Reset and Exit. The
operation of these keys is described below. The function is
✱
] [6] menu
activated by pressing and holding the key for 2 seconds.
'Stay' - Stay Arm
Arms the system. All Stay/Away type zones will be auto-
matically bypassed. Delay type zones will provide entry
and Exit Delay. The Quick Arm feature must be enabled
for this key to function (Section [015], Option [4]) . If
Quick Arming is not enabled, the user must enter their
access code after pressing the function key in order to arm
the system in the Stay mode.
'Away' - Away Arm
Arms the system. All Stay/Away type zones will be
active at the end of the Exit Delay. Delay type zones will
provide entry and Exit Delay. The Quick Arm feature
must be enabled for this key to function (Section [015],
option [4]) . If Quick Arming is not enabled, the user must
enter their access code after pressing the function key in
order to arm the system in the Away mode.
14
Global Delay zones will always have an entry delay,
Quick Arm Enable option is enabled the panel can
Quick Arm Enable Quick Arm Enable
Quick Exit