Advertisement
GLM NETWORK
CONNECTORS
MAINS
INPUT
Figure 2: Connector layout on the rear panel of the 8430A.
Figure 3: Connector panel of the 8430A.
Maintain Symmetry
Place the monitors at an equal distance from
the listening position and symmetrically relative
to the room walls. Place the listening position
on the room front-back centreline and the moni-
tors at an equal distance from this centreline.
Minimise Reflections
Acoustic reflections are created by objects
close to the monitors. Such objects can be
desks, cabinets, computer monitors etc.
Acoustic reflections can cause unwanted sound
colouration and sound image instability. These
can be minimised by placing the monitors and
the listening position clear of reflective surfaces.
Minimum Clearances
Ensure sufficient clearance for amplifier cooling
and reflex port function. The minimum clear-
ance is 3 cm (13/16 in) behind, above, and on
both sides of the monitor. The ambient temper-
ature should be less than 35 degrees Celsius
(95°F.)
Mounting Options
The Genelec 8430A offers the Iso-Pod™ (Isola-
tion Positioner/Decoupler™) vibration insulat-
ing stand allowing tilting of the monitor acous-
WARNING:
ELECTRIC SHOCK HAZARD. DO NOT OPEN. DO
NOT SUBJECT TO WATER OR MOISTURE. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
USE EARTHED MAINS CONNECTION ONLY.
AVERTISSEMENT:
RISQUE DE CHOC ÉLECTRIQUE. NE PAS
OUVRIR. NE PAS EXPOSER À L'EAU OU L'HUMIDITÉ. AUCUN
COMPOSANT À L'INTÉRIEUR REMPLAÇABLE PAR
L'UTILISATEUR. ADRESSER TOUTE RÉPARATION À UN
PERSONNEL QUALIFIÉ. CET APPAREIL DOIT ÊTRE
RACCORDÉ À LA TERRE.
LAITE ON LIITETTÄVÄ SUOJAMAADOITUSKOSKETTIMILLA VARUS-
TETTUUN PISTORASIAAN. APPARATET MÅ TILKOPLES JORDET
STIKKONTAKT. APPARATEN SKALL ANSLUTAS TILL JORDAT UTTAG.
RESET TO FACTORY
GLM NETWORK
ETHERNET AND
SETTINGS: PUSH
BUTTON FOR 10 SEC
ANALOG INPUT
MAINS INPUT
ANALOG
50 / 60 Hz 60 W
IN
100 - 240 V~
ETHERNET
8430A
SMART ACTIVE MONITOR
2
1
MADE IN FINLAND
www.genelec.com
3
SERIAL NUMBER
+
-
GND
IN
tic axis towards the listener. The bottom of the
monitor has a 3/8 in UNC thread. The rear has
two M6 x 10 mm threads for wall or ceiling
mounts. Genelec offers a selection of mounting
accessories.
Safety Considerations
Servicing must only be performed by qualified
service personnel. The monitor must not be
opened.
• Do not use the monitor with an unearthed
mains cable or an unearthed mains
connection.
• Do not expose the monitor to water or
moisture. Do not place any objects filled
with liquid, such as vases, on the monitor
or near it.
• This monitor is capable of producing
sound pressure levels in excess of 85 dB,
which may cause permanent hearing
damage.
• Free flow of air behind the monitor is
necessary to maintain sufficient cooling. Do
not obstruct airflow around the monitor.
• The device is not completely disconnected
from the AC mains service unless the mains
power cord is detached from the device or
the mains outlet.
Guarantee
This product is guaranteed for a period of two
years against faults in materials or workman-
ship. Refer to supplier for full sales and guar-
antee terms.
Compliance to FCC Rules
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
This device may not cause harmful interfer-
ence, and this device must accept any interfer-
ence received, including interference that may
cause undesired operation.
Note: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful interfer-
ence in a residential installation. This equip-
ment generates, uses and can radiate radio
frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interfer-
ence will not occur in a particular installation. If
this equipment does cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help
Modifications not expressly approved by the
manufacturer could void the user's authority to
operate the equipment under FCC rules.
Advertisement
