Related Manuals for Raymarine Quantum
Summary of Contents for Raymarine Quantum
- Page 1 Quantum™ INSTALLATION INSTRUCTIONS English (EN) Date: 12-2015 Document number: 87209-1 © 2015 Raymarine UK Limited...
- Page 3 Software updates Important: Check the Raymarine website for the latest software releases for your product. www.raymarine.com/software Product handbooks The latest versions of all English and translated handbooks are available to download in PDF format from the website www.raymarine.com.
-
Page 5: Table Of Contents
Contents Chapter 1 Important information......7 Chapter 8 Technical support ......39 Certified Installation ........... 7 8.1 Raymarine product support and servicing ....40 Transmitted power density levels ........ 7 8.2 Operation instructions........... 41 IEEE statement ............7 8.3 Viewing product information ........41 ICNIRP Guidelines............. - Page 6 Quantum Radome...
-
Page 7: Chapter 1 Important Information
Raymarine recommends certified installation by a documentation provided. Raymarine approved installer. A certified installation qualifies for enhanced product warranty benefits. Contact your Raymarine dealer for further details, Warning: Radio frequency radiation and refer to the separate warranty document packed hazard with your product. -
Page 8: Disclaimer
Disclaimer Compass safe distance Raymarine does not warrant that this product is To prevent potential interference with the vessel's magnetic compasses, ensure an adequate distance error-free or that it is compatible with products is maintained from the product. manufactured by any person or entity other than Raymarine. -
Page 9: Radar Licensing
To the best of our knowledge, the information in this document was correct at the time it was produced. However, Raymarine cannot accept liability for any inaccuracies or omissions it may contain. In addition, our policy of continuous product improvement may change specifications without notice. - Page 10 Quantum Radome...
-
Page 11: Chapter 2 Document And Product Information
Chapter 2: Document and product information Chapter contents • 2.1 Document information on page 12 • 2.2 Parts supplied on page 13 • 2.3 Quantum™ Radome product overview on page 13 Document and product information... -
Page 12: Document Information
Convention summary on Fishfinder This document contains important information how to access a application related to the installation of your Raymarine product. particular function menu: Menu The document includes information to help you: or menu option. > Set-up > Sounder •... -
Page 13: Parts Supplied
• 12 V or 24 V operation. • Waterproof to IPX 6. Multiple Quantum™ Radar scanners Only 1 (one) Quantum™ Radar scanner can be used at any one time, per networked system. If you have more than one Quantum™ Radar... - Page 14 Quantum Radome...
-
Page 15: Chapter 3 Planning The Installation
Chapter 3: Planning the installation Chapter contents • 3.1 Installation checklist on page 16 • 3.2 Required additional components on page 16 • 3.3 Multifunction display compatibility on page 17 • 3.4 Multifunction display software requirements on page 17 • 3.5 Tools required on page 18 •... -
Page 16: Installation Checklist
Route all cables. and connections for suitable cables and adaptors Drill cable and mounting holes. for existing cable installations. (The Quantum™ scanner is Wi-Fi-enabled, and can be operated Make all connections into equipment. without a fixed data cable.) Secure all equipment in place. -
Page 17: Multifunction Display Compatibility
Series Damage caused by incomplete updates are not covered by Raymarine warranty. By downloading the software update package, you agree to these terms. Incompatible multifunction displays This product is NOT compatible with the following Software updates legacy Raymarine multifunction displays. -
Page 18: Tools Required
3 mm drill bit 10 mm drill bit Adhesive tape D13406-2 13 mm socket Item Description Torque wrench Multifunction display Quantum™ Radome RayNet data cable Example: basic Radar system (wireless data connection) 12 / 24 V D13410-2 Item Description Multifunction display Quantum™... -
Page 19: Location Requirements
3.7 Location requirements Example: expanded system (power cables not shown) The optimum height for the Quantum™ scanner is a location that is high enough above the waterline to give a long range line-of-sight to the horizon, but not so high as to be adversely affected by the boat's pitching and rolling. -
Page 20: Product Dimensions
• Multiple scanners should be mounted in a way that minimizes interference between the vertical beamwidths of the 2 scanners. • In all cases, you should aim to achieve as much physical separation as possible, to minimize any potential interference. Quantum Radome... -
Page 21: Chapter 4 Cables And Connections
Chapter 4: Cables and connections Chapter contents • 4.1 General cabling guidance on page 22 • 4.2 Connections overview on page 23 • 4.3 Power connection on page 25 • 4.4 Network connection on page 27 Cables and connections... -
Page 22: General Cabling Guidance
Ensure that all data cables are properly shielded that the cable shielding is intact (e.g. hasn’t been • Ensure that any non-Raymarine cables are of the scraped off by being squeezed through a tight area). correct quality and gauge. For example, longer... -
Page 23: Connections Overview
• A separate power cable is supplied with all 1. Cable routing for a scanner mounted on a Quantum™ Radar variants. platform, using separate cables for the power • Not all Quantum™ radar variants are supplied and data connection. with a RayNet cable. Refer to the Chapter 2 2. - Page 24 2. 12 V / 24 V power connection. A80308 Note: • A separate power cable is supplied with all Quantum™ Radar variants. • Not all Quantum™ radar variants are supplied with a RayNet cable. Refer to the Chapter 2 Document and product information section for more information.
-
Page 25: Power Connection
• The power cable for each unit in your system should be run as a separate, single length of 2-wire cable from the unit to the vessel's battery or distribution panel. • Raymarine recommends a minimum wire gauge of 14AWG (2.08 mm ) for any length of cable extension. - Page 26 NOT cover every scenario. If you are unsure how to provide the correct level of protection, please consult an authorized Raymarine dealer or a suitably qualified professional marine electrician. D13348-1 Implementation — direct connection to battery •...
-
Page 27: Network Connection
This product is fully insulated and does 12 / 24 V NOT require separate grounding. D13408-2 Item Description Quantum™ Radome (for clarity, only the connections area of the underside of the unit is shown here). Connector panel of compatible Raymarine multifunction display. RayNet data cable. - Page 28 Multiple multifunction display configuration A Raymarine network switch can be used to connect the unit to more than 1 multifunction display. 12 / 24 V D13409-2 Item Description Quantum™ radome (for clarity, only the connections area of the underside of the unit is shown here).
-
Page 29: Chapter 5 Mounting
Chapter 5: Mounting Chapter contents • 5.1 Mounting the scanner on page 30 • 5.2 Radar scanner protection — sailing vessels on page 31 Mounting... -
Page 30: Mounting The Scanner
3. Drill out the pilot holes to 10 mm diameter. 15 Nm (133 lbf/inch). 4. Place the Quantum™ scanner in position. If you 8. Attach a safety lanyard (not supplied) to your are fitting it on a planing vessel, shim the rear... -
Page 31: Radar Scanner Protection - Sailing Vessels
5.2 Radar scanner protection — sailing Multiple Quantum™ Radar scanners vessels Only 1 (one) Quantum™ Radar scanner can be used at any one time, per networked system. Additional considerations apply when installing the If you have more than one Quantum™ Radar Radar scanner on a sailing vessel. - Page 32 Radar scanner; for other vessels, it may be more appropriate to fit it below the scanner. Raymarine does not supply Radar guards but recommends that you select a guard that is attached directly to the mast and is completely separate to the Radar mounting bracket.
-
Page 33: Chapter 6 System Checks And Troubleshooting
Chapter 6: System checks and troubleshooting Chapter contents • 6.1 Post installation procedures on page 34 • 6.2 Troubleshooting on page 35 System checks and troubleshooting... -
Page 34: Post Installation Procedures
Standby mode within 5 seconds. When (MFD) documentation, to switch on and connect to the connection to the MFD is restored, return the the Quantum™ scanner, and to carry out the initial scanner to Transmit mode using the Radar: Tx checks and setup tasks. -
Page 35: Troubleshooting
All Raymarine products are, prior to packing and shipping, subjected to comprehensive test and quality assurance programs. However, if you experience problems with the operation of your... - Page 36 If the Quantum™ Radome is connected to the multifunction display (MFD) via a SeaTalk or RayNet network switch, ensure that: • All relevant equipment is correctly connected to the network switch.
-
Page 37: Chapter 7 Maintenance
Chapter 7: Maintenance Chapter contents • 7.1 Maintenance on page 38 • 7.2 Unit cleaning instructions on page 38 Maintenance... -
Page 38: Maintenance
• Examine all cables for signs of chafing, cuts or other damage. Warning: High voltages This product may contain high voltages. Do NOT remove any covers or otherwise attempt to access internal components, unless specifically instructed in the documentation provided. Quantum Radome... -
Page 39: Chapter 8 Technical Support
Chapter 8: Technical support Chapter contents • 8.1 Raymarine product support and servicing on page 40 • 8.2 Operation instructions on page 41 • 8.3 Viewing product information on page 41 Technical support... -
Page 40: Raymarine Product Support And Servicing
Servicing and warranty 3614 905 Raymarine offers dedicated service departments for Sweden support.se@raymarine.com warranty, service, and repairs. (0)317 (Raymarine subsidiary) Don’t forget to visit the Raymarine website to 633 670 register your product for extended warranty benefits: Finland +358 support.fi@raymarine.com http://www.raymarine.co.uk/display/?id=788. (0)207... -
Page 41: Operation Instructions
8.2 Operation instructions 8.3 Viewing product information For detailed operation instructions for your product, You can view information about your unit from the refer to the documentation that accompanies your Diagnostics menu on a compatible multifunction display. display. This option displays information such as product serial number and software version. - Page 42 Quantum Radome...
-
Page 43: Chapter 9 Technical Specification
Chapter 9: Technical specification Chapter contents • 9.1 Technical specification on page 44 Technical specification... -
Page 44: Technical Specification
40 ns to 14.7µs 400 ns to 22 µs Chirp lengths: Pulse repetition frequency: 2083 Hz to 4167 Hz Chirp bandwidth: Up to 32 MHz Standby mode: Scanner rotation - OFF Scanner transmission - OFF Wi-Fi link - ON Quantum Radome... -
Page 45: Chapter 10 Spares And Accessories
Chapter 10: Spares and accessories Chapter contents • 10.1 Quantum™ Radar accessories on page 46 • 10.2 Network hardware on page 46 • 10.3 Network cable connector types on page 47 • 10.4 RayNet to RayNet cables and connectors on page 48 •... -
Page 46: Quantum™ Radar Accessories
Accessories HS5 RayNet A80007 5–port switch for network Item Part number network switch connection of multiple devices featuring RayNet 10 m (32.8 ft.) Quantum™ A80309 connectors. Equipment with power cable RJ45 SeaTalk connectors A80274 5 m (16.4 ft.) Quantum™ can also be connected using data cable suitable adapter cables. -
Page 47: Network Cable Connector Types
10.3 Network cable connector types There are 2 types of network cable connector — RayNet, and RJ45 SeaTalk RJ45 SeaTalk connector. RayNet connector. Spares and accessories... -
Page 48: Raynet To Raynet Cables And Connectors
This adapter features a RayNet (female) socket at one end, and a RayNet (male) plug at the other end. Adapter cable with a RayNet (male) Suitable for joining (female) RayNet cables together for plug on both ends. longer cable runs. Quantum Radome... -
Page 49: Raynet To Rj45 Adapter Cables
• E55051 (10 m). • A62135 (15 m). • E55052 (20 m). Adapter cable with a RayNet (female) Directly connect a Raymarine radar scanner with an RJ45 socket on one end, and a waterproof SeaTalk (male) cable to a RayNet network switch (e.g. - Page 50 Quantum Radome...
- Page 52 Raymarine UK Limited, Marine House, Cartwright Drive, Fareham, PO15 5RJ. United Kingdom. Tel: +44 (0)1329 246 700...