Table of Contents
Advertisement
Advertisement
Table of Contents
Troubleshooting
Related Manuals for DeLonghi ECAM25462
Summary of Contents for DeLonghi ECAM25462
- Page 1 5713220781/ 08.13...
- Page 2 BEAN TO CUP ESPRESSO AND CAPPUCCINO MACHINE Instruction for use ECAM25462/ECAM25467...
-
Page 7: Table Of Contents
CORD CLAMP MAKING CAPPUCCINO AND MILK BASED COFFEES ..13 Filling and attaching the milk container ......... 13 INTRODUCTION ............7 Adjusting the amount of froth ..........13 Symbols used in these instructions ........... 7 Preparing cappuccino.............. 13 Letters in brackets ..............7 Making CAFFELATTE/MACCHIATO/FLAT WHITE/ MILK ... -
Page 8: Introduction
INTRODUCTION enabling the appliance to be unplugged when necessary. • Unplug directly from the plug only. Never pull the power Thank you for choosing this automatic espresso and cappuccino cable as you could damage it. machine. We hope you enjoy using your new appliance. • To disconnect the appliance completely, release the main Take a few minutes to read this Instruction for Use. switch at the back of the appliance (fig. -
Page 9: Instructions For Use
INSTRUCTION FOR USE (When in the settings MENU: turn to select the required fun- ction). Read these instructions carefully before using the appliance. B7. MILK MENU button: to access preparation of MACCHIATO, Failure to respect these instructions may result in burns or CAFFELATTE, FLAT WHITE and MILK. -
Page 10: Connecting The Appliance
Connecting the appliance • To enjoy your coffee even more and improve the perfor- mance of your appliance, we recommend installing a wa- Important! ter softener filter as described in the section “Install filter”. Check that the mains power supply voltage corresponds to If your model is not provided with a filter, you can request the value indicated on the rating plate on the bottom of the one from De’Longhi Customer Service. -
Page 11: Menu Settings
MENU SETTINGS Auto-Off Auto-off can be set so that the appliance goes off after 15 or 30 Access the settings menu by pressing the MENU button; the minutes, or after 1, 2 or 3 hours. following menu items are available: 1. -
Page 12: Setting Water Hardness
2. Turn the selection dial until “Set temperature” is displa- Default values (reset) yed; This resets all menu settings and programmed quantities back to the default values (with the exception of the language 3. Press the button. which remains as set). 4. -
Page 13: Customising The "My Coffee" Quantity
• warm the cups with hot water (using the hot water fun- Coffee selected Quantity in cup (ml) ction); ≃30 (program. MY COFFEE • enable the cup warmer in the settings menu and leave from ≃20 to ≃180) the cups until they are warm; ≃40 • raise the coffee temperature in the settings menu. SHORT ≃60 STANDARD Making coffee using coffee beans ≃90 LONG Important! ≃120 EXTRA LONG Do not use caramelised or candied coffee beans as they could stick to the coffee mill and make it unusable. -
Page 14: Making Cappuccino And Milk Based Coffees
could spread through the inside of the machine and dirty milk spouts. Adjust the length of the milk spout. To move it. This could damage the appliance. it nearer the cup, simply pull it downwards (fig. 20). • Never use more than one level measure or it could dirty 7. Follow the instructions below for each function. the inside of the machine or block the funnel. -
Page 15: Cleaning The Milk Container After Each Use
and (if needed for the drink), coffee delivery starts. 3. The appliance starts dispensing milk. Release the button. 4. Once the required quantity of milk has been delivered into Pease note: the cup, press the CAPPUCCINO button again. • Milk or coffee dispensing can be interrupted at any time 5. -
Page 16: Cleaning
Cleaning the drip tray and condensate tray of hot water. To modify these quantities, proceed as follows: 1. Make sure the hot water spout is attached correctly. Important! 2. Position a container under the spout. The drip tray is fitted with a level indicator (red) showing the 3. -
Page 17: Cleaning The Milk Container
9. Close the infuser door. Important! 10. Replace the water tank. The infuser may not be extracted when the machine is on. 1. Make sure the machine is correctly turned off (see “Tur- Cleaning the milk container ning off”, page 9). Clean the milk container each time you prepare milk as descri- 2. -
Page 18: Setting Water Hardness
out of the spout and the message “RINSING PLEASE Important! WAIT” is displayed. • Descaler contains acids which may irritate the skin and 14. When the water tank is completely empty, the message eyes. It is vital to respect the manufacturer’s safety war- “Rinsing complete Confirm?”... -
Page 19: Water Softener Filter
WATER SOFTENER FILTER filter: 1. Extract the tank and exhausted filter; Some models come supplied with the water softener filter. If 2. Take the new filter out of its packet and proceed as illu- this is not the case with your model, we recommend purcha- strated in points 2, 3, 4, 5 and 6 in the previous section. -
Page 20: Displayed Messages
DISPLAYED MESSAGES MESSAGE DISPLAYED POSSIBLE CAUSE SOLUTION FILL TANK Insufficient water in the tank. Fill the tank with water and/or insert it correctly, pushing it as far as it will go until it clicks into place (fig. 4). EMPTY GROUNDS CONTAINER The grounds container (A14) is full. -
Page 21: Troubleshooting
EMPTY CIRCUIT FILL CIRCUIT The water circuit is empty. Press OK to deliver water from the spout (D5) until it alternating with flows out normally. HOT WATER Confirm? SET DIAL TO CLEAN Milk has been delivered recently and Turn the froth adjustment dial to CLEAN. the tubes inside the milk container must be cleaned. - Page 22 The coffee is delivered too slowly The coffee is ground too finely. Turn the grinding adjustment dial one or in drops. click clockwise towards “7” while the cof- fee mill is in operation (fig. 11). Continue one click at a time until coffee delivery is satisfactory.
- Page 23 ELECTRICAL REQUIREMENTS (UK ONLY) Before using this appliance ensure that the voltage indicated on the product corresponds with the main voltage in your home, if you are in any doubt about your supply contact your local electricity company. The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13 amp capacity. Should this plug not fit the socket outlets in your home, it should be cut off and replaced with a suitable plug, following the procedure outlined below.