Page 1 Accessories, spare parts and modification of your Toyota A wide variety of non-genuine spare parts and accessories for Toyota vehi- cles are currently available in the market. You should know that Toyota does not warrant these products and is not responsible for their performance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle.
Page 2 ● Seat belt pretensioner system ● Be sure to check with your Toyota dealer for precautionary measures or spe- cial instructions regarding installation of a mobile two-way radio system. Vehicle data recordings Your Toyota is equipped with several sophisticated computers that will record certain data, such as: •...
Page 3 EDR. ● Disclosure of the EDR data Toyota will not disclose the data recorded in an EDR to a third party except when: • An agreement from the vehicle’s owner (or the lessee for a leased vehi- cle) is obtained •...
Page 4 Be sure to have the systems of the SRS airbag and seat belt pretensioner removed and disposed of by a qualified service shop or by your Toyota dealer before you scrap your vehicle.
Page 5 1-1. For safe use Before driving Floor mat Use only floor mats designed specifically for vehicles of the same model and model year as your vehicle. Fix them securely in place onto the carpet. Insert the retaining hooks (clips) into the floor mat eyelets. Turn the upper knob of each retaining hook (clip) to secure the floor mats in place.
Page 6 ■ Do not use floor mats designed for other models or different model year ● vehicles, even if they are Toyota Genuine floor mats. Only use floor mats designed for the driver’s seat. ● Always install the floor mat securely using the retaining hooks (clips) pro- ●...
Page 7 1-1. For safe use For safety drive For safe driving, adjust the seat and mirror to an appropriate position before driving. Correct driving posture Adjust the angle of the seat- back so that you are sitting straight up and so that you do not have to lean forward to steer.
Page 8: Adjusting The Mirrors
1-1. For safe use Adjusting the mirrors Make sure that you can see backward clearly by adjusting the inside and outside rear view mirrors properly. ( P. 129, 131) CAUTION Observe the following precautions. Failure to do so may result in death or serious injury. Do not adjust the position of the driver’s seat while driving.
Page 9 1-1. For safe use Seat belts Make sure that all occupants are wearing their seat belts before driving the vehicle. Correct use of the seat belts ● Extend the shoulder belt so that it comes fully over the shoulder, but does not come into contact with the neck or slide off the shoulder.
Page 10 1-1. For safe use Adjusting the seat belt shoulder anchor height (front seats) Push the seat belt shoulder anchor down while pressing the release button. Push the seat belt shoulder anchor up. Move the height adjuster up and down as needed until you hear a click.
Page 11 Seat belt extender ■ If your seat belts cannot be fastened securely because they are not long enough, personalized seat belt extender is available from your Toyota dealer free of charge. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 12 Each seat belt should be used by one person only. Do not use a seat belt ● for more than one person at once, including children. Toyota recommends that children be seated in the rear seat and always ● use a seat belt and/or an appropriate child restraint system.
Page 13 Ensure that the belt and plate are locked and the belt is not twisted. ● If the seat belt does not function correctly, immediately contact your Toyota dealer. Replace the seat assembly, including the belts, if your vehicle has been ●...
Page 14 1-1. For safe use CAUTION Using a seat belt extender ■ Do not wear the seat belt extender if you can fasten the seat belt without ● the extender. Do not use the seat belt extender when installing a child restraint system ●...
Page 15 1-1. For safe use SRS airbags The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury. ◆...
Page 16 1-1. For safe use SRS airbag system components Front impact sensors “AIR BAG ON” and “AIR BAG OFF” indicator lights Front passenger occupant classification system (ECU Curtain shield airbags and sensors) Side impact sensors (rear) Seat cushion airbag Driver airbag Side impact sensors (front Driver’s seat...
Page 17 1-1. For safe use Your vehicle is equipped with ADVANCED AIRBAGS designed based on the US motor vehicle safety standards (FMVSS208). The airbag sensor assembly (ECU) controls airbag deployment based on infor- mation obtained from the sensors etc. shown in the system compo- nents diagram above.
Page 18 An infant or child who is too small to use a seat belt should be properly secured using a child restraint sys- tem. Toyota strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly restrained. The rear seats are safer for infants and children than the front passenger seat.
Page 19 1-1. For safe use CAUTION SRS airbag precautions ■ Do not sit on the edge of the seat or ● lean against the dashboard. Do not allow a child to stand in front of ● the SRS front passenger airbag unit or sit on the knees of a front passenger.
Page 20 1-1. For safe use CAUTION SRS airbag precautions ■ Do not attach anything to or lean any- ● thing against areas such as the dash- board, steering wheel pad and lower portion of the instrument panel. These items can become projectiles when the SRS driver, front passenger and driver’s knee airbag deploy.
Page 21 ■ Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer. The SRS airbags may malfunction or deploy (inflate) accidentally, causing death or serious injury. Installation, removal, disassembly and repair of the SRS airbags ●...
Page 22 1-1. For safe use If the SRS airbags deploy (inflate) ■ Bruising and slight abrasions may result from contact with a deploying ● (inflating) SRS airbag. A loud noise and white powder will be emitted. ● Parts of the airbag module (steering wheel hub, airbag cover and inflator) as ●...
Page 23 1-1. For safe use Conditions under which the SRS airbags may deploy (inflate), other than ■ a collision The SRS front airbags and SRS side and curtain shield airbags may also deploy if a serious impact occurs to the underside of your vehicle. Some examples are shown in the illustration.
Page 24 1-1. For safe use Types of collisions that may not deploy the SRS airbags (SRS side and ■ curtain shield airbags) The SRS side and curtain shield airbags may not activate if the vehicle is subjected to a collision from the side at certain angles, or a collision to the side of the vehicle body other than the passenger compartment.
Page 25 When to contact your Toyota dealer ■ In the following cases, the vehicle will require inspection and/or repair. Con- tact your Toyota dealer as soon as possible. Any of the SRS airbags have been inflated. ● The front of the vehicle is damaged or ●...
Page 26 1-1. For safe use The portion of the front pillars, rear pil- ● lars or roof side rail garnishes (padding) containing the curtain shield airbags inside is scratched, cracked, or other- wise damaged. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 27 1-1. For safe use Front passenger occupant classification system Your vehicle is equipped with a front passenger occupant classi- fication system. This system detects the conditions of the front passenger seat and activates or deactivates the devices for the front passenger. SRS warning light Seat belt reminder light “AIR BAG OFF”...
Page 28 1-1. For safe use Condition and operation in the front passenger occupant classi- fication system Adult ■ “AIR BAG ON” and “AIR BAG OFF” “AIR BAG ON” indicator lights Indicator/ SRS warning light warning light Seat belt reminder light flashing Front passenger airbag Side airbag Activated...
Page 29 1-1. For safe use Child restraint system with infant ■ “AIR BAG ON” and “AIR BAG OFF” “AIR BAG indicator lights OFF” Indicator/ SRS warning light warning light Seat belt reminder light flashing Front passenger airbag Deactivated Side airbag on the front passenger seat Activated Curtain shield airbag Devices...
Page 30 1-1. For safe use There is a malfunction in the system ■ “AIR BAG ON” and “AIR BAG OFF” “AIR BAG OFF” indicator lights Indicator/ SRS warning light warning light Seat belt reminder light Front passenger airbag Deactivated Side airbag on the front passenger seat Activated Curtain shield airbag...
Page 31 1-1. For safe use CAUTION Front passenger occupant classification system precautions ■ Observe the following precautions regarding the front passenger occupant classification system. Failure to do so may cause death or serious injury. Wear the seat belt properly. ● Make sure the front passenger’s seat belt plate has not been left inserted ●...
Page 32 SRS warning light may come on to indicate a malfunction of the front passenger occupant classification system. In this case, contact your Toyota dealer immediately. Child restraint systems installed on the rear seat should not contact the ●...
Page 33 1-1. For safe use Safety information for children Observe the following precautions when children are in the vehi- cle. Use a child restraint system appropriate for the child, until the child becomes large enough to properly wear the vehicle’s seat belt.
Page 34 1-1. For safe use Child restraint systems A child restraint system for a small child or baby must itself be properly restrained on the seat with the LATCH anchors or the lap portion of the lap/shoulder belt. The laws of all 50 states of the U.S.A. and Canada now require the use of child restraint systems.
Page 35 1-1. For safe use Types of child restraints Child restraint systems are classified into the following 3 types according to the age and size of the child: Rear facing Infant seat/con- Forward facing Convertible vertible seat seat Booster seat Selecting an appropriate child restraint system ■...
Page 36 In an accident, the child can be crushed against the windshield, or between you and the vehicle’s interior. Toyota strongly urges the use of a proper child restraint system that con- ●...
Page 37 1-1. For safe use CAUTION When children are in the vehicle ■ Do not allow children to play with the seat belt. If the seat belt becomes twisted around a child’s neck, it may lead to choking or other serious injuries that could result in death.
Page 38 1-1. For safe use Installing child restraints Follow the child restraint system manufacturer's instructions. Firmly secure child restraints to the seats using the LATCH anchors or a seat belt. Attach the top tether strap when installing a child restraint. The lap/shoulder belt can be used if your child restraint system is not compatible with the LATCH (Lower Anchors and Tethers for Children) system.
Page 39 1-1. For safe use Installation with LATCH system Widen the gap between the seat cushion and seatback slightly. Type A Latch the hooks of the lower straps onto LATCH anchors. If the child restraint has a top tether strap, the top tether strap should be latched onto the top tether strap anchor.
Page 40 1-1. For safe use Installing child restraints using a seat belt Rear-facing Infant seat/convertible seat ■ Place the child restraint sys- tem on the rear seat facing the rear of the vehicle. Run the seat belt through the child restraint system and insert the plate into the buckle.
Page 41 1-1. For safe use Forward-facing Convertible seat ■ Place the child restraint sys- tem on the seat facing the front of the vehicle. If your child restraint system interferes with a head restraint and cannot be installed properly, install the child restraint system after removing head...
Page 42 1-1. For safe use Booster seat ■ Place the child restraint sys- tem on the seat facing the front of the vehicle. Sit the child in the child restraint system. Fit the seat belt to the child restraint sys- tem according to the manu- facturer's instructions insert the plate into the...
Page 43 1-1. For safe use Child restraint systems with a top tether strap Adjust the head restraint to the downmost position. (if equipped) ( P. 124) Secure the child restraint sys- tem using the seat belt or LATCH anchors. Open the anchor bracket cover, latch the hook onto the anchor bracket and tighten the top tether strap.
Page 44 1-1. For safe use Laws and regulations pertaining to anchorages ■ The LATCH system conforms to FMVSS225 or CMVSS210.2. Child restraint systems conforming to FMVSS213 or CMVSS213 specifica- tions can be used. This vehicle is designed to conform to SAE J1819. CAUTION When installing a booster seat ■...
Page 45 1-1. For safe use CAUTION When installing a child restraint system ■ When using the LATCH anchors for a child restraint system, move the seat ● as far back as possible, with the seatback close to the child restraint sys- tem.
Page 46 Keep the trunk lid closed. ● If you smell exhaust gases in the vehicle even when the trunk lid is closed, ● open the windows and have the vehicle inspected at your Toyota dealer as soon as possible. When parking ■...
Page 47 1-2. Theft deterrent system Engine immobilizer system The vehicle’s keys have built-in transponder chips that prevent the engine from starting if a key has not been previously regis- tered in the vehicle’s on-board computer. Never leave the keys inside the vehicle when you leave the vehi- cle.
Page 48 1-2. Theft deterrent system System maintenance ■ The vehicle has a maintenance-free type engine immobilizer system. Conditions that may cause the system to malfunction ■ If the grip portion of the key is in contact with a metallic object ● If the key is in close proximity to or touching a key to the security system ●...
Page 49 1-2. Theft deterrent system Alarm The alarm The alarm uses light and sound to give an alert when an intrusion is detected. The alarm is triggered in the following situations when the alarm is set: ● A locked door or trunk is unlocked or opened in any way other than using the entry function, wireless remote control or mechanical key.
Page 50 1-2. Theft deterrent system System maintenance ■ The vehicle has a maintenance-free type alarm system. Items to check before locking the vehicle ■ To prevent unexpected triggering of the alarm and vehicle theft, make sure of the following: Nobody is in the vehicle. ●...
Page 51 1-2. Theft deterrent system COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 52 2. Instrument cluster Warning lights and indicators The warning lights and indicators on the instrument cluster and center panel inform the driver of the status of the vehicle’s vari- ous systems. For the purpose of explanation, the following illustration dis- plays all warning lights and indicators illuminated.
Page 53 2. Instrument cluster Warning lights Warning lights inform the driver of malfunctions in the indicated vehi- cle’s systems. Brake system warning ABS warning light light ( P. 491) ( P. 492) (U.S.A.) (U.S.A.) Brake system warning ABS warning light light ( P. 491) ( P.
Page 54 There may be a mal- function in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer. : If equipped : The light flashes in yellow to indicate a malfunction.
Page 55 2. Instrument cluster Indicators The indicators inform the driver of the operating state of the vehicle’s various systems. Turn signal indicator Cruise control indicator ( P. 182) ( P. 197) (Green) Headlight indicator “ECO MODE” indicator ( P. 184) ( P. 175) (U.S.A.) 1, 3 Tail light indicator...
Page 56 Have the vehicle inspected by your Toyota dealer immedi- ately if this occurs.
Page 57 2. Instrument cluster Gauges and meters (drive monitor display) The displayed content may differ depending on the type of meter. Tachometer Displays the engine speed in revolutions per minute. Speedometer Fuel gauge Drive monitor display The drive monitor display presents the driver with a variety of driving- related data including the current outside air temperature.
Page 58 2. Instrument cluster Drive monitor display Engine coolant temperature gauge Displays the engine coolant tem- perature. Eco Driving Indicator Zone Dis- play ( P. 90) Outside temperature display ( P. 404) Shift position and gear position indicator ( P. 172, 174, 176) Trip information ( P.
Page 59 2. Instrument cluster Trip information Switching the display ■ Items displayed switched pressing “DISP” switch. Odometer ■ Displays the total distance the vehicle has been driven. Except vehicles with a manual transmission: Press and hold the “DISP” switch to change the display to the Eco Driving Indicator Light customi- zation screen.
Page 60 2. Instrument cluster Driving range ■ Displays the estimated maximum distance that can be driven with the quantity of fuel remaining. • This distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ from that dis- played.
Page 61 2. Instrument cluster The meters and display illuminate when ■ Vehicles without a smart key system The engine switch is in the “ON” position. Vehicles with a smart key system The engine switch is in IGNITION ON mode. When disconnecting and reconnecting battery terminals ■...
Page 62 2. Instrument cluster Gauges and meters (multi-information dis- play) The displayed content may differ depending on the type of meter. Tachometer Displays the engine speed in revolutions per minute. Speedometer Fuel gauge Multi-information display The multi-information display presents the driver with a variety of driving- related data including the current outside air temperature.
Page 63 2. Instrument cluster Multi-information display Outside temperature display ( P. 404) Driving monitor ( P. 84) Warning messages ( P. 503) Eco Driving Indicator Zone Dis- play ( P. 90) Trip information ( P. 84) Shift position and gear position indicator ( P.
Page 64 2. Instrument cluster Trip information Switching the display ■ Items displayed switched by pressing the dis- play change button. Odometer ■ Displays the total distance the vehicle has been driven. Trip meter A/trip meter B ■ Displays the distance the vehicle has been driven since the meter was last reset.
Page 65 2. Instrument cluster Driving range ■ Displays the estimated maximum distance that can be driven with the quantity of fuel remaining. • This distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ from that dis- played.
Page 66 2. Instrument cluster Customizing vehicle features It is possible to customize the language and Eco Driving Indicator Light settings using the “DISP” switch. When customizing vehicle features, ensure that the vehicle is parked in a safe place with the shift the shift lever to P (continuously variable transmission) or N (manual transmission) and the parking brake set.
Page 67 2. Instrument cluster Items that can be changed ■ Function Default setting Customized setting French Language English Spanish ECO Driving Indicator ON (Self-lighting) Light : Except vehicles with a manual transmission The meters and display illuminate when ■ Vehicles without a smart key system The engine switch is in the “ON”...
Page 68 2. Instrument cluster CAUTION The display at low temperatures ■ Allow the interior of the vehicle to warm up before using the display. At extremely low temperatures, the display monitor may respond slowly, and display changes may be delayed. For example, there is a lag between the driver’s shifting and the new gear number appearing on the display.
Page 69 2. Instrument cluster Eco Driving Indicator (except vehicles with a manual transmission) Eco Drive Indicator Light During Eco-friendly acceleration Drive monitor display operation (Eco driving), Eco Driv- ing Indicator Light will turn on. When the acceleration exceeds Zone of Eco driving, and when the vehicle is stopped, the light turns off.
Page 70 2. Instrument cluster Eco Drive Indicator Zone Display Suggests Zone of Eco driving with Drive monitor display current Eco driving ratio based on acceleration. Eco driving ratio based on acceleration If the acceleration exceeds Zone of Eco driving, the right side of Eco Driving Indicator Zone Display blinks.
Page 71 3-1. Key information Keys The keys The following keys are provided with the vehicle. Vehicles without a smart key system (type A) Keys Key number plate Vehicles without a smart key system (type B) Keys Operating the wireless remote control function Key number plate Vehicles with a smart key system Electronic keys...
Page 72 3-1. Key information Wireless remote control (if equipped) Vehicles without a smart key system Locks all the doors ( P. 97) Unlocks all the doors ( P. 97) Pressing the button unlocks the driver’s door. Pressing the but- ton again within 5 seconds unlocks the other doors.
Page 73 If you lose your keys ■ New genuine keys can be made by your Toyota dealer using the other key (vehicles without a smart key system) or mechanical key (vehicles with a smart key system) and the key number stamped on your key number plate.
Page 74 Confirmation of the registered key number ■ The number of keys already registered to the vehicle can be confirmed. Ask your Toyota dealer for details. If a wrong key is used (vehicles with a smart key system) ■ The key cylinder rotates freely to isolate inside mechanism.
Page 75 When an electronic key is lost (vehicles with a smart key system) ■ If the electronic key remains lost, the risk of vehicle theft increases signifi- cantly. Visit your Toyota dealer immediately with all remaining electronic keys that was provided with your vehicle. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 76 3-2. Opening, closing and locking the doors Doors Unlocking and locking the doors from the outside ◆ Smart key system (if equipped) Carry the electronic key to enable this function. Grip the driver’s door handle to unlock the door. Grip the passenger’s door handle to unlock all the doors.* Make sure to touch the sensor...
Page 77 3-2. Opening, closing and locking the doors Vehicles with a smart key system Locks all the doors Unlocks all the doors Pressing the button unlocks the driver’s door. Pressing the but- ton again within 5 seconds unlocks the other doors. ◆...
Page 78 3-2. Opening, closing and locking the doors Operation signals ■ A buzzer sounds and the emergency flashers flash to indicate that the doors have been locked/unlocked. (Locked: once; Unlocked: twice) Security feature ■ If a door is not opened within approximately 60 seconds after the vehicle is unlocked, the security feature automatically locks the vehicle again.
Page 79 3-2. Opening, closing and locking the doors Unlocking and locking the doors from the inside ◆ Door lock switches Locks all the doors Unlocks all the doors ◆ Inside lock buttons Locks the door Unlocks the door The front doors can be opened by pulling the inside handle even if the lock buttons are in the lock position.
Page 80 3-2. Opening, closing and locking the doors Rear door child-protector lock The door cannot be opened from inside the vehicle when the lock is set. Unlock Lock These locks can be set to prevent children from opening the rear doors. Push down on each rear door switch to lock both rear doors.
Page 81 3-2. Opening, closing and locking the doors Automatic door locking and unlocking systems The following functions can be set or cancelled: Function Operation Shift position linked door locking Shifting the shift lever out of P locks function all doors. Shift position linked door unlocking Shifting the shift lever to P unlocks function all doors.
Page 82 3-2. Opening, closing and locking the doors Setting and canceling the functions ■ To switch between set and canceled, follow the procedure below: Vehicles without a smart key system: Close all the doors and switch the engine switch to the “ON” position. (Perform step within 20 seconds.) Vehicles with a smart key system: Close all the doors and switch the engine switch to IGNITION ON mode.
Page 83 3-2. Opening, closing and locking the doors Switching the door unlock function (vehicles with a smart key system) ■ It is possible to set which doors the entry function unlocks using the wireless remote control. Turn the engine switch off. When the indicator light on the key surface is not on, press and hold for approximately 5 seconds while pressing and holding The setting changes each time an operation is performed, as shown below.
Page 84 3-2. Opening, closing and locking the doors Conditions affecting the operation of the smart key system or wireless ■ remote control (with a wireless remote control function) Vehicles without a smart key system The wireless remote control function may not operate normally in the follow- ing situations: When the wireless key battery is depleted ●...
Page 85 3-2. Opening, closing and locking the doors Trunk The trunk can be opened using the trunk opener, entry function, wireless remote control or key. Opening the trunk from inside the vehicle Pull up the lever to release the trunk lid. Opening the trunk from outside the vehicle ◆...
Page 86 3-2. Opening, closing and locking the doors ◆ Wireless remote control (if equipped) Vehicles without a smart key system Press and hold the switch. Vehicles with a smart key system Press and hold the switch. ◆ Key (vehicles with a key cylinder on the trunk lid) Turn the key clockwise to release the trunk lid.
Page 87 3-2. Opening, closing and locking the doors Operation signal (with a wireless remote control function) ■ A buzzer sounds to indicate that the trunk has been opened. Trunk light ■ The trunk light turns on when the trunk is opened. Function to prevent the trunk being locked with the electronic key inside ■...
Page 88 3-2. Opening, closing and locking the doors CAUTION Caution while driving ■ Keep the trunk lid closed while driving. ● If the trunk lid is left open, it may hit near-by objects while driving or lug- gage in the trunk may be unexpectedly thrown out, causing an accident. In addition, exhaust gases may enter the vehicle, causing death or a seri- ous health hazard.
Page 89 Do not attach any accessories other than genuine Toyota parts to the trunk ● lid. Such additional weight on the trunk lid may cause the lid to suddenly shut again after it is opened.
Page 90 3-2. Opening, closing and locking the doors Smart key system The following operations can be performed simply by carrying the electronic key on your person, for example in your pocket. (The driver should always carry the electronic key.) ● Locks and unlocks the doors ( P. 97) ●...
Page 91 3-2. Opening, closing and locking the doors Effective range (areas within which the electronic key is detected) ■ When locking or unlocking the doors The system can be operated when the electronic key is within about 2.3 ft. (0.7 m) of either of the outside front door handles.
Page 92 3-2. Opening, closing and locking the doors Alarm Situation Correction procedure An attempt was made Close all of the doors to lock the vehicle while and lock the doors a door was open. again. Vehicles with a drive monitor display: Retrieve the electronic attempt was made to key from the passenger...
Page 93 3-2. Opening, closing and locking the doors Alarm Situation Correction procedure The driver’s door was opened while any shift Interior alarm sounds position other than P Shift the shift lever to P. 1, 2 continuously was selected without turning off the engine switch.
Page 94 3-2. Opening, closing and locking the doors Conditions affecting operation ■ The smart key system uses weak radio waves. In the following situations, the communication between the electronic key and the vehicle may be affected, preventing the smart key system, wireless remote control and engine immobi- lizer system from operating properly.
Page 95 3-2. Opening, closing and locking the doors Note for the entry function ■ Even when the electronic key is within the effective range (detection areas), ● the system may not operate properly in the following cases: • The electronic key is too close to the window or outside door handle, near the ground, or in a high place when the doors are locked or unlocked.
Page 96 3-2. Opening, closing and locking the doors Vehicles with a multi-information display: If the electronic key is inside the ● vehicle and a door handle becomes wet during a car wash, a message may be shown on the multi-information display and a buzzer will sound outside the vehicle.
Page 97 3-2. Opening, closing and locking the doors Certification for the smart key system ■ For the U.S.A. FCC ID: HYQ23AAB FCC ID: HYQ14FBA NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 98 ( P. 111) The radio waves may affect the operation of such devices. If necessary, the entry function can be disabled. Ask your Toyota dealer for details, such as the frequency of radio waves and timing of the emitted radio waves.
Page 99 3-3. Adjusting the seats Front seats Adjustment procedure Manual seat Seat position adjustment lever Vertical height adjustment lever (driver’s side only) Seatback angle adjustment lever Power seat (driver’s side only) Seat position adjustment Seat cushion (front) angle switch adjustment switch Seatback angle adjustment Vertical height...
Page 100 3-3. Adjusting the seats CAUTION Seat adjustment ■ Be careful that the seat does not hit passengers or luggage. ● Do not recline the seat more than necessary when the vehicle is in motion ● to reduce the risk of sliding under the lap belt. If the seat is too reclined, the lap belt may slide past the hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt, increasing the risk of death or serious injury in the event of...
Page 101 3-3. Adjusting the seats Rear seats The seatbacks of the rear seats can be folded down. Folding down the rear seatbacks Stow the rear outside seat belt buckles and stow the rear cen- ter seat belt buckle as shown. Pull the seatback lock release knob and fold the seatback down.
Page 102 3-3. Adjusting the seats CAUTION When folding the rear seatbacks down ■ Observe the following precautions. Failure to do so may result in death or serious injury. Do not fold the seatbacks down while driving. ● Stop the vehicle on level ground, set the parking brake and shift the shift ●...
Page 103 3-3. Adjusting the seats Head restraints Head restraints are provided for all seats. Front seats Pull the head restraints up. Down Push the head restraint down while pressing the lock release button. Lock release button Rear seats Type A Pull the head restraints up. Down Push the head restraint down while pressing the lock release button.
Page 104 3-3. Adjusting the seats Removing the head restraints (except for fixed rear head restraints) ■ Pull the head restraint up while pressing the lock release button. Lock release button Installing the head restraints (except for fixed rear head restraints) ■ Front seats and rear outside seats Align the head restraint with the installa- tion holes and push it down to the lock...
Page 105 3-3. Adjusting the seats CAUTION Head restraint precautions ■ Observe the following precautions regarding the head restraints. Failure to do so may result in death or serious injury. Use the head restraints designed for each respective seat. ● Adjust the head restraints to the correct position at all times. ●...
Page 106 3-4. Adjusting the steering wheel and mirrors Steering wheel Adjustment procedure Hold the steering wheel and push the lever down. Adjust to the ideal position by moving the steering wheel hori- zontally and vertically. After adjustment, pull the lever up to secure the steering wheel.
Page 107 3-4. Adjusting the steering wheel and mirrors CAUTION Caution while driving ■ Do not adjust the steering wheel while driving. Doing so may cause the driver to mishandle the vehicle and cause an acci- dent, resulting in death or serious injury. After adjusting the steering wheel ■...
Page 108 3-4. Adjusting the steering wheel and mirrors Inside rear view mirror The rear view mirror’s position can be adjusted to enable suffi- cient confirmation of the rear view. Adjusting the height of rear view mirror The height of the rear view mirror can be adjusted to suit your driving posture.
Page 109 3-4. Adjusting the steering wheel and mirrors Auto anti-glare inside rear view mirror Responding to the level of brightness of the headlights of vehicles behind, the reflected light is automatically reduced. Changing automatic anti-glare function mode On/off When the automatic anti-glare function is in ON mode, the indica- tor illuminates.
Page 110 3-4. Adjusting the steering wheel and mirrors Outside rear view mirrors Adjustment procedure To select a mirror to adjust, press the switch. Left Right To adjust the mirror, press the switch. Right Down Left Folding the mirrors Push the mirror back in the direc- tion of the vehicle’s rear.
Page 111 3-4. Adjusting the steering wheel and mirrors Mirror angle can be adjusted when ■ Vehicles without a smart key system The engine switch is in the “ACC” or “ON” position. Vehicles with a smart key system The engine switch is in ACCESSORY or IGNITION ON mode. When the mirrors are fogged up (if equipped) ■...
Page 112 3-5. Opening and closing the windows Power windows Opening and closing procedures The power windows can be opened and closed using the switches. Operating the switch moves the windows as follows: Closing One-touch closing (driver’s win- dow only) Opening One-touch opening (driver’s window only)
Page 113 3-5. Opening and closing the windows The power windows can be operated when ■ Vehicles without a smart key system The engine switch is in the “ON” position. Vehicles with a smart key system The engine switch is in IGNITION ON mode. Operating the power windows after turning the engine off ■...
Page 114 If you release the switch while the window is moving, start again from the beginning. If the window continues to close but then re-open slightly even after perform- ing the above procedure correctly, have the vehicle inspected by your Toyota dealer. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 115 3-5. Opening and closing the windows CAUTION Observe the following precautions. Failure to do so may result in death or serious injury. Closing the windows ■ The driver is responsible for all the power window operations, including the ● operation for the passengers. In order to prevent accidental operation, especially by a child, do not let a child operate the power windows.
Page 116 3-5. Opening and closing the windows Moon roof Use the overhead switches to open and close the moon roof and tilt it up and down. Opening and closing ■ Opens the moon roof The moon roof stops slightly before the fully open position to reduce wind noise.
Page 117 3-5. Opening and closing the windows The moon roof can be operated when ■ Vehicles without a smart key system The engine switch is in the “ON” position. Vehicles with a smart key system The engine switch is in IGNITION ON mode. Operating the moon roof after turning the engine off ■...
Page 118 Check to make sure that the moon roof is completely closed and then release the switch. If the moon roof does not fully close even after performing the above proce- dure correctly, have the vehicle inspected by your Toyota dealer. Moon roof open reminder function ■...
Page 119 3-5. Opening and closing the windows CAUTION Opening the moon roof ■ Observe the following precautions. Failure to do so may cause death or serious injury. Do not allow any passengers to put their hands or heads outside the vehi- ●...
Page 120 4-1. Before driving Driving the vehicle The following procedures should be observed to ensure safe driving: Starting the engine P. 161, 164 Driving Automatic transmission or continuously variable transmission With the brake pedal depressed, shift the shift lever to D. ( P.
Page 121 4-1. Before driving Parking the vehicle Automatic transmission or continuously variable transmission With the shift lever in D, depress the brake pedal. Shift the shift lever to P. ( P. 172, 174, 176) Set the parking brake. ( P. 183) Vehicles without a smart key system: Turn the engine switch to the “LOCK”...
Page 122 4-1. Before driving Starting off on a steep uphill Automatic transmission or continuously variable transmission Make sure that the parking brake is set and shift the shift lever to Gently depress the accelerator pedal. Release the parking brake. Manual transmission With the parking brake firmly set and the clutch pedal fully depressed, shift the shift lever to 1.
Page 123 When the brake pedal is depressed suddenly and vehicle speed is reduced ● sharply (continuously variable transmission) Breaking in your new Toyota ■ To extend the life of the vehicle, observing the following precautions is recom- mended: For the first 186 miles (300 km): ●...
Page 124 4-1. Before driving CAUTION Observe the following precautions. Failure to do so may result in death or serious injury. When driving the vehicle ■ Do not drive if you are unfamiliar with the location of the brake and accel- ● erator pedals to avoid depressing the wrong pedal.
Page 125 4-1. Before driving CAUTION Observe the following precautions. Failure to do so may result in death or serious injury. When driving on slippery road surfaces ■ Sudden braking, acceleration and steering may cause tire slippage and ● reduce your ability to control the vehicle. Sudden acceleration, engine braking due to shifting, or changes in engine ●...
Page 126 If you hear a squealing or scraping noise (brake pad wear limit indica- ■ tors) Have the brake pads checked and replaced by your Toyota dealer as soon as possible. Rotor damage may result if the pads are not replaced when needed.
Page 127 4-1. Before driving CAUTION Observe the following precautions. Failure to do so may result in death or serious injury. When the vehicle is parked ■ Do not leave cigarette lighters in the vehicle. If a cigarette lighter is in a ●...
Page 128 4-1. Before driving CAUTION Observe the following precautions. Failure to do so may result in death or serious injury. When braking ■ When the brakes are wet, drive more cautiously. ● Braking distance increases when the brakes are wet, and this may cause one side of the vehicle to brake differently than the other side.
Page 129 4-1. Before driving NOTICE When driving the vehicle (vehicles with a manual transmission) ■ Do not depress the accelerator and brake pedals at the same time during ● driving, as this may restrain driving torque. Do not shift gears unless the clutch pedal is fully depressed. After shifting, ●...
Page 130 Engine damage caused by water immersion ● In the event that you drive on a flooded road and the vehicle is flooded, be sure to have your Toyota dealer check the following: Brake function ● Changes in quantity and quality of engine oil, transaxle fluid, etc.
Page 131 Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. ( P. 156) Toyota does not recommend towing a trailer with your vehicle. Your vehicle is not designed for trailer towing. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 132 4-1. Before driving Calculation formula for your vehicle Cargo capacity Total load capacity (vehicle capacity weight) ( P. 544) When 2 people with the combined weight of A lb. (kg) are riding in your vehicle, which has a total load capacity (vehicle capacity weight) of B lb.
Page 133 4-1. Before driving CAUTION Things that must not be carried in the trunk ■ The following things may cause a fire if loaded in the trunk: Receptacles containing gasoline ● Aerosol cans ● Storage precautions ■ Observe the following precautions. Failure to do so may prevent the pedals from being depressed properly, may block the driver’s vision, or may result in items hitting the driver or passengers, possibly causing an accident.
Page 134 Seating capacity means the maximum number of occupants whose estimated average weight is 150 lb. (68 kg) per person. ◆ Towing capacity Toyota does not recommend towing a trailer with your vehicle. ◆ Cargo capacity Cargo capacity may increase or decrease depending on the weight and the number of occupants.
Page 135 Trailer towing Toyota does not recommend towing a trailer with your vehicle. Toyota also does not recommend the installation of a tow hitch or the use of a tow hitch carrier for a wheelchair, scooter, bicy- cle, etc. Your vehicle is not designed for trailer towing or for the use of tow hitch mounted carriers.
Page 136 4-1. Before driving Dinghy towing (except vehicles with a man- ual transmission) Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home. NOTICE To avoid serious damage to your vehicle ■ Do not tow your vehicle with four wheels on the ground.
Page 137 4-1. Before driving Dinghy towing (vehicles with a manual transmission) Your vehicle can be dinghy towed in a forward direction (with 4 wheels on the ground) behind a motor home. Towing your vehicle with 4 wheels on the ground To prevent damage to your vehicle, perform the following procedures before towing.
Page 138 4-1. Before driving NOTICE Dinghy towing direction ■ Do not tow the vehicle backwards. Doing so may cause serious damage. To prevent the steering from locking ■ Vehicles without a smart key system: Ensure the engine switch is in the “ACC”...
Page 139 4-2. Driving procedures Engine (ignition) switch (vehicles without a smart key system) Starting the engine Automatic transmission or continuously variable transmission Check that the parking brake is set. Check that the shift lever is set in P. Firmly depress the brake pedal. Turn the engine switch to the “START”...
Page 140 “LOCK” position. If the engine does not start ■ The engine immobilizer system may not have been deactivated. ( P. 66) Contact your Toyota dealer. When the steering lock cannot be released ■ When starting the engine, the engine switch may seem stuck in the “LOCK”...
Page 141 Do not crank the engine for more than 30 seconds at a time. This may ● overheat the starter and wiring system. Do not race a cold engine. ● If the engine becomes difficult to start or stalls frequently, have your vehi- ● cle checked by your Toyota dealer immediately. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 142 4-2. Driving procedures Engine (ignition) switch (vehicles with a smart key system) Performing the following operations when carrying the elec- tronic key on your person starts the engine or changes engine switch modes. Starting the engine Check that the parking brake is set. Vehicles with a drive monitor display Continuously variable transmission: Check that the shift lever is set in P.
Page 143 4-2. Driving procedures Vehicles with a multi-information display Continuously variable transmission: Check that the shift lever is set in P. Firmly depress the brake pedal. Manual transmission: Check that the shift lever is set in N. Firmly depress the clutch pedal. will be displayed on the multi-information display.
Page 144 4-2. Driving procedures Changing engine switch modes Modes can be changed by pressing the engine switch with the brake pedal (continuously variable transmission) or clutch pedal (manual transmission) released. (The mode changes each time the switch is pressed.) Vehicles with a drive monitor display The emergency flashers can be used.
Page 145 4-2. Driving procedures Vehicles with a multi-information display The emergency flashers can be used. multi-information display will not be displayed. ACCESSORY mode Some electrical components such as the audio system can be used. “POWER ON” will be displayed on the multi-information display. IGNITION ON mode All electrical components can be used.
Page 146 4-2. Driving procedures When stopping the engine with the shift lever in a position other than P (vehicles with a continuously variable transmission) If the engine is stopped with the shift lever in a position other than P, the engine switch will not be turned off but instead be turned to ACCESSORY mode.
Page 147 ■ The engine immobilizer system may not have been deactivated. ( P. 66) ● Contact your Toyota dealer. Vehicles with a continuously variable transmission: Check that the shift lever ● is securely set in P. The engine may not start if the shift lever is displaced out of P.
Page 148 When the smart key system indicator light flashes in yellow (vehicles ■ with a drive monitor display) The system may be malfunctioning. Have the vehicle inspected by your Toyota dealer immediately. When “CHECK SMART KEY SYSTEM” will be displayed on the multi- ■ information display (vehicles with a multi-information display) The system may be malfunctioning.
Page 149 ● If the engine becomes difficult to start or stalls frequently, have your vehi- ● cle checked by your Toyota dealer immediately. Symptoms indicating a malfunction with the engine switch ■ If the engine switch seems to be operating somewhat differently than usual, such as the switch sticking slightly, there may be a malfunction.
Page 150 4-2. Driving procedures Automatic transmission Shifting the shift lever While the engine switch is in the “ON” position, depress the brake pedal and move the shift lever. : If equipped COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 151 4-2. Driving procedures Shift position uses Shift position Function Parking the vehicle or starting the engine Reversing Neutral Normal driving Position for engine braking Position for more powerful engine braking Position for maximum engine braking : Shifting to the D position allows the system to select a gear suitable for driving conditions.
Page 152 4-2. Driving procedures Continuously variable transmission (vehi- cles without paddle shift switches) Shifting the shift lever Vehicles without a smart key system: While the engine switch is in the “ON” position, depress the brake pedal and move the shift lever. Vehicles with a smart key system: While the engine switch is in IGNITION ON mode, depress the brake pedal and move the shift lever.
Page 153 4-2. Driving procedures Shift position purpose Shift position Objective or function Parking the vehicle/starting the engine Reversing Neutral Normal driving Engine braking Maximum engine braking : To improve fuel efficiency and reduce noises, set the shift lever in D for normal driving.
Page 154 4-2. Driving procedures Continuously variable transmission (vehi- cles with paddle shift switches) Shifting the shift lever Vehicles without a smart key system: While the engine switch is in the “ON” position, depress the brake pedal and move the shift lever. Vehicles with a smart key system: While the engine switch is in IGNITION ON mode, depress the brake pedal and move the shift lever.
Page 155 4-2. Driving procedures Shift position purpose Shift position Objective or function Parking the vehicle/starting the engine Reversing Neutral Normal driving 7-speed sport sequential shiftmatic mode driving ( P. 178) : To improve fuel efficiency and reduce noises, set the shift lever in D for normal driving.
Page 156 M This may indicate a malfunction in the continuously variable transmission system. Have the vehicle inspected by your Toyota dealer immediately. (In this situation, the transmission will operate in the same manner as when the shift lever is in D.) When the vehicle comes to a stop with the shift lever in the M position ■...
Page 157 4-2. Driving procedures When driving with cruise control activated ■ Even when performing the following actions with the intent of enabling engine braking, engine braking will not activate because cruise control will not be canceled. While driving in D or 7-speed sport sequential shiftmatic mode, downshifting ●...
Page 158 4-2. Driving procedures Manual transmission Shifting the shift lever Fully depress the clutch pedal before operating the shift lever, and then release it slowly. Shifting the shift lever to R Shift the shift lever to R while lift- ing up the ring section. : If equipped COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 159 4-2. Driving procedures Maximum allowable speeds ■ Observe the following maximum allowable speeds in each gear when maxi- mum acceleration is necessary. mph (km/h) Maximum speed Shift position Vehicles with 15-inch and Vehicles with 17-inch tires 16-inch tires 30 (49) 30 (49) 56 (91) 56 (90)
Page 160: Operating Instructions
4-2. Driving procedures Turn signal lever Operating instructions Right turn Lane change to the right (move the lever partway and release The right hand signals will flash 3 times. Lane change to the left (move the lever partway and release The left hand signals will flash 3 times.
Page 161 4-2. Driving procedures Parking brake Operating instructions To set the parking brake, fully pull the parking brake lever while depressing the brake pedal. To release the parking brake, slightly raise the lever and lower it completely while press- ing the button. : For U.S.A.
Page 162 4-3. Operating the lights and wipers Headlight switch The headlights can be operated manually or automatically. Operating instructions Turning the end of the lever turns on the lights as follows: Type A The daytime running lights turn on. The side marker, park- ing, tail, license plate, daytime running lights and instrument panel...
Page 163 4-3. Operating the lights and wipers Type B The daytime running lights turn on The side marker, park- ing, tail, license plate, daytime running lights and instrument panel lights turn on. The headlights and all the lights listed above (except daytime run- ning lights) turn on.
Page 164 4-3. Operating the lights and wipers Type C The headlights and all the lights listed below turn on and off auto- matically. (Vehicles without smart system: When engine switch is in the “ON” position) (Vehicles with a smart key system: When the engine switch IGNITION ON mode)
Page 165 4-3. Operating the lights and wipers Type D The headlights and all the lights listed below turn on and off auto- matically. (Vehicles without smart system: When engine switch is in the “ON” position) (Vehicles with a smart key system: When the engine switch IGNITION ON mode)
Page 166 4-3. Operating the lights and wipers Turning on the high beam headlights With the headlights on, push the lever away from you to turn on the high beams. Pull the lever toward you to the center position to turn the high beams off.
Page 167 4-3. Operating the lights and wipers Automatic light off system ■ Vehicles without a smart key system When the headlights are on: The headlights and tail lights turn off 30 sec- ● onds after the engine switch is turned to the “ACC” or “LOCK” position and a door is opened and closed.
Page 168 4-3. Operating the lights and wipers Battery-saving function ■ In the following conditions, the headlights and the other remaining lights will go off automatically after 20 minutes in order to prevent the vehicle battery from being discharged: The headlights and/or tail lights are on. ●...
Page 169 4-3. Operating the lights and wipers Fog light switch The fog lights secure excellent visibility in difficult driving con- ditions, such as in rain and fog. Turns the front fog lights Turns the front fog lights : For U.S.A. : For Canada Fog lights can be used when ■...
Page 170 4-3. Operating the lights and wipers Windshield wipers and washer Operating the wiper lever The wiper operation is selected by moving the lever as follows. When intermittent windshield wiper operation is selected, the wiper interval can be also adjusted. Intermittent windshield wiper operation Low speed windshield...
Page 171 Do not operate the switch continually as the washer fluid pump may over- heat. When a nozzle becomes blocked ■ In this case, contact your Toyota dealer. Do not try to clear it with a pin or other object. The nozzle will be damaged. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 172 4-4. Refueling Opening the fuel tank cap Perform the following steps to open the fuel tank cap: Before refueling the vehicle ● Close all the doors and windows, and turn the engine switch off. ● Confirm the type of fuel. Fuel types ■...
Page 173 4-4. Refueling NOTICE Refueling ■ Do not spill fuel during refueling. Doing so may damage the vehicle, such as causing the emission control system to operate abnormally or damaging fuel system components or the vehicle’s painted surface. Opening the fuel tank cap Pull up the opener to open the fuel filler door.
Page 174 CAUTION When replacing the fuel tank cap ■ Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury.
Page 175 4-5. Using the driving support systems Cruise control Summary of functions Use the cruise control to maintain a set speed without depressing the accelerator pedal. Indicators Cruise control switch Setting the vehicle speed Press the “ON-OFF” button to activate the cruise control. Cruise control indicator will come Press the button again to deacti- vate the cruise control.
Page 176 4-5. Using the driving support systems Adjusting the set speed To change the set speed, operate the lever until the desired set speed is obtained. Increases the speed Decreases the speed Fine adjustment: Momentarily move the lever in the desired direc- tion.
Page 177 If the cruise control speed cannot be set or if the cruise control cancels imme- diately after being activated, there may be a malfunction in the cruise control system. Have the vehicle inspected by your Toyota dealer. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 178 If the cruise control speed cannot be set or if the cruise control cancels imme- diately after being activated, there may be a malfunction in the cruise control system. Have the vehicle inspected by your Toyota dealer. CAUTION To avoid operating the cruise control by mistake ■...
Page 179 4-5. Using the driving support systems Rear view monitor system The rear view monitor system assists the driver by displaying guide lines and an image of the view behind the vehicle while backing up, for example while parking. The screen illustrations used in this text are intended as examples, and may differ from the image that is actually displayed on the screen.
Page 180 4-5. Using the driving support systems Using the rear view monitor system Screen description ■ Vehicle width guide lines The line indicates a guide path when the vehicle is being backed straight up. The displayed width is wider than the actual vehicle width. Vehicle center guide lines These lines indicate the estimated vehicle center on the ground.
Page 181 4-5. Using the driving support systems Rear view monitor system precautions Area displayed on screen ■ The rear view monitor system displays an image of the view from the bumper of the rear area of the vehicle. To adjust the image on the rear view monitor system screen.
Page 182 4-5. Using the driving support systems Rear view monitor system camera ■ The camera for the rear view monitor system located above the license plate. ● Using the camera If the camera lens becomes dirty, it cannot transmit a clear image. If water droplets, snow or mud adhere to the lens, rinse it with water and wipe with a soft cloth.
Page 183 4-5. Using the driving support systems ● When the ground behind the vehicle slopes up sharply The distance guide lines will appear to be closer to the vehi- cle than the actual distance. Because of this, objects will appear to be farther away than they actually are.
Page 184 4-5. Using the driving support systems ● When any part of the vehicle sags When any part of the vehicle sags due to the number of pas- sengers or the distribution of the load, there is a margin of error between the fixed guide lines on the screen and the actual distance/course on the A margin of error...
Page 185 4-5. Using the driving support systems Vehicle width guide lines ■ Visually check the surroundings and the area behind the vehicle. In the case shown below, the truck appears to be outside of the vehi- cle width guide lines and the vehicle does not look as if it hits the truck.
Page 186 If you notice any of the following symptoms, refer to the likely cause and the solution, and re-check. If the symptom is not resolved by the solution, have the vehicle inspected by your Toyota dealer. Likely cause Solution The image is difficult to see •...
Page 187 4-5. Using the driving support systems CAUTION When using the rear view monitor system ■ The rear view monitor system is a supplemental device intended to assist the driver when backing up. When backing up, be sure to check visually behind and all around the vehicle before proceeding.
Page 188 Do not expose the camera to strong impact as this could cause a malfunc- ● tion. If this happens, have the vehicle inspected by your Toyota dealer as soon as possible. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 189 4-5. Using the driving support systems Driving assist systems To help enhance driving safety and performance, the following systems operate automatically in response to various driving situations. Be aware, however, that these systems are supple- mentary and should not be relied upon too heavily when operat- ing the vehicle.
Page 190 4-5. Using the driving support systems When the TRAC or VSC system is operating The slip indicator light will flash while the TRAC or VSC system is operating. Disabling the TRAC system If the vehicle gets stuck in mud, dirt or snow, the TRAC system may reduce power from the engine to the wheels.
Page 191 When the “TRAC OFF” indicator light comes on even if the VSC OFF ■ switch has not been pressed TRAC cannot be operated. Contact your Toyota dealer. Sounds and vibrations caused by the ABS, brake assist, TRAC and VSC ■...
Page 192 4-5. Using the driving support systems CAUTION The ABS does not operate effectively when ■ The limits of tire gripping performance have been exceeded (such as ● excessively worn tires on a snow covered road). The vehicle hydroplanes while driving at high speed on wet or slick roads. ●...
Page 193 The ABS, TRAC and VSC systems will not function correctly if different tires are installed on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels. Handling of tires and the suspension ■...
Page 194 4-6. Driving tips Winter driving tips Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a man- ner appropriate to the prevailing weather conditions. Preparation for winter ● Use fluids that are appropriate to the prevailing outside tempera- tures.
Page 195 4-6. Driving tips When driving the vehicle Accelerate the vehicle slowly, keep a safe distance between you and the vehicle ahead, and drive at a reduced speed suitable to road con- ditions. When parking the vehicle Park the vehicle and move the shift lever to P (automatic transmission or continuously variable transmission), 1 or R (manual transmission) without setting the parking brake.
Page 196 Repairing or replacing snow tires (vehicles with a tire pressure warn- ■ ing system) Request repairs or replacement of snow tires from Toyota dealers or legiti- mate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.
Page 197 5-1. Basic Operations Audio system types Without Multimedia system With Multimedia system P. 283 With navigation system Owners of models equipped with a navigation system should refer to the “Navigation System Owner's Manual”. Using cellular phones ■ Interference may be heard through the audio system's speakers if a cellular phone is being used inside or close to the vehicle while the audio system is operating.
Page 198 5-1. Basic Operations CAUTION U.S.A. ■ FCC ID: ACJ932PTA184 NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 199 5-1. Basic Operations CAUTION Canada ■ IC: 216J-PTA184 NOTE: This device complies with Industry Canada license-exempt RSS stan- dard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Page 200 5-1. Basic Operations NOTICE To prevent battery discharge ■ Do not leave the audio system on longer than necessary when the engine is off. To avoid damaging the audio system ■ Take care not to spill drinks or other fluids on the audio system. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 201 5-1. Basic Operations Steering wheel audio switches Some audio features can be controlled using the switches on the steering wheel. Operation may differ depending on the type of audio system or navigation system. For details, refer to the manual provided with the audio system or navigation system.
Page 202 5-1. Basic Operations AUX port/USB port Connect an iPod, USB memory device or portable audio player to the AUX port/USB port as indicated below. Press select “iPod”, “USB” or “AUX”. Connecting using the AUX port/USB port iPod ■ Open the cover and connect an iPod using an iPod cable.
Page 203 5-2. Using the audio system Optimal use of the audio system Sound quality (treble/bass) and volume balance can be adjusted. Displays the current mode Changes the following setting • Sound quality and volume bal- ance ( P. 228) The sound quality and balance set- ting can be changed to produce the best sound.
Page 204 5-2. Using the audio system Adjusting sound quality ■ Turning adjusts the level. Sound quality Mode Turn to the Turn to the Level mode displayed left right Bass* “BASS” -5 to 5 High Treble* “TREBLE” -5 to 5 Front/rear volume “FADER”...
Page 205 5-4. Playing audio CDs and MP3/WMA discs CD player operation Insert a disc or press to begin listening to a disc. Power Displays text message Volume Playback Eject a disc Select a folder (MP3/WMA discs only), fast-forward or Repeat play reverse Random playback Search playback...
Page 206 5-4. Playing audio CDs and MP3/WMA discs Using the CD player Selecting a track ■ Turn or press to move up or to move down until the desired track number is displayed. Selecting a track from a track list ■ Press The track list will be displayed.
Page 207 5-4. Playing audio CDs and MP3/WMA discs Random playback ■ Press (RDM). Tracks are played in a random order until (RDM) is pressed again. Switching the display ■ Press to display or hide the CD title. If there is additional text, is displayed.
Page 208 5-4. Playing audio CDs and MP3/WMA discs Scanning folders ■ Press and hold until you hear a beep. The first 10 seconds of the first file in each folder will be played. When the desired folder is reached, press again. Selecting a file ■...
Page 209 Error messages ■ If an error message is displayed, refer to the following table and take the appropriate measures. If the problem is not rectified, take the vehicle to your Toyota dealer. Message Cause Correction procedures • The disc is dirty or •...
Page 210 5-4. Playing audio CDs and MP3/WMA discs MP3 and WMA files ■ MP3 (MPEG Audio LAYER3) is a standard audio compression format. Files can be compressed to approximately 1/10 of their original size by using MP3 compression. WMA (Windows Media Audio) is a Microsoft audio compression format. This format compresses audio data to a size smaller than that of the MP3 for- mat.
Page 211 5-4. Playing audio CDs and MP3/WMA discs Compatible disc formats ● The following disc formats can be used. • Disc formats: CD-ROM Mode 1 and Mode 2 CD-ROM XA Mode 2, Form 1 and Form 2 • File formats: ISO9660 Level 1, Level 2, (Romeo, Joliet) MP3 and WMA files written in any format other than those listed above may not play correctly, and their file names and folder names may not be displayed correctly.
Page 212 5-4. Playing audio CDs and MP3/WMA discs Extensions ● If the file extensions .mp3 and .wma are used for files other than MP3 and WMA files, they will be mistakenly recognized and played as MP3 and WMA files. This may result in large amounts of interference and damage to the speakers.
Page 213 5-4. Playing audio CDs and MP3/WMA discs NOTICE Discs and adapters that cannot be used ■ Do not use the following types of discs. Also, do not use 3 in. (8 cm) disc adapters, Dual Discs or printable discs. Doing so may damage the player and/or disc insert/eject function. Discs that have a diameter that is not 4.7 in.
Page 214 5-3. Using the radio Radio operation Select “AM” or “FM” to begin listening to the radio. Power AM/FM mode button Volume Scan for receivable stations Station selectors Seek a frequency Adjust frequency or select an item Setting station presets Search for a desired station by turning or pressing Press and hold a desired station selector button until you hear a beep.
Page 215 5-3. Using the radio Scanning radio stations Scanning preset radio stations ■ Press and hold until you hear a beep. Preset stations will be played for 5 seconds each. When the desired station is reached, press again. Scanning all radio stations within range ■...
Page 216 5-5. Using an external device Listening to an iPod Connecting an iPod enables you to enjoy music from the vehicle speakers. Press until “iPod” is displayed. Connecting an iPod P. 227 Control panel Power Displays text message Volume Playback Fast-forward or reverse Select a song Repeat play iPod menu mode...
Page 217 5-5. Using an external device Selecting a play mode Press (BROWSE) to select iPod menu mode. Turning clockwise changes the play mode in the following order: “Playlists” “Artists” “Albums” “Songs” “Podcasts” “Genres” “Composers” “Audiobooks” Press to select the desired play mode. Play mode list ■...
Page 218 5-5. Using an external device Selecting a list ■ Turn to display the first selection list. Press to select the desired item. Pressing the knob changes to the second selection list. Repeat the same procedure to select the desired item. To return to the previous selection list, press (BACK).
Page 219 5-5. Using an external device Shuffle playback Pressing (RDM) changes the shuffle playback mode in the fol- lowing order: Track shuffle Album shuffle Off. Switching the display Press to display or hide the album title. If there is additional text, is displayed.
Page 220 5-5. Using an external device iPod functions ■ When an iPod is connected and the audio source is changed to iPod mode, ● the iPod will resume play from the same point in which it was last used. Depending on the iPod that is connected to the system, certain functions ●...
Page 221 ■ If an error message is displayed, refer to the following table and take the appropriate measures. If the problem is not rectified, take the vehicle to your Toyota dealer. Message Cause/Correction procedures This indicates that the data in the iPod cannot “iPod ERROR”...
Page 222 5-5. Using an external device Compatible models ■ The following iPod , iPod nano , iPod classic , iPod touch and iPhone devices can be used with this system. Made for ● • iPod touch (4th generation) • iPod touch (3rd generation) •...
Page 223 5-5. Using an external device Listening to a USB memory device Connecting a USB memory device enables you to enjoy music from the vehicle speakers. Press until “USB” is dis- played. Connecting a USB memory P. 227 Control panel Power Displays text message Volume Playback...
Page 224 5-5. Using an external device Selecting a folder Selecting a folder ■ Press ) or ) to select the desired folder. Selecting a folder and file from a folder list ■ Press A folder list will be displayed. Turn and press to select a folder and a file.
Page 225 ■ If an error message is displayed, refer to the following table and take the appropriate measures. If the problem is not rectified, take the vehicle to your Toyota dealer. Message Cause/Correction procedures This indicates a problem in the USB memory “ERROR”...
Page 226 5-5. Using an external device USB memory ■ Compatible devices ● USB memory that can be used for MP3 and WMA playback Compatible device formats ● The following device formats can be used: • USB communication formats: USB2.0 FS (12 Mbps) •...
Page 227 5-5. Using an external device WMA file compatibility ● • Compatible standards WMA Ver. 7, 8, 9 • Compatible sampling frequencies HIGH PROFILE 32, 44.1, 48 (kHz) • Compatible bit rates HIGH PROFILE 48-320 (kbps, CBR) File names ● The only files that can be recognized as MP3/WMA and played are those with the extension .mp3 or .wma.
Page 228 5-5. Using an external device CAUTION Caution while driving ■ Do not connect USB memory or operate the controls. NOTICE To prevent damage to USB memory ■ Do not leave USB memory in the vehicle. The temperature inside the vehi- ●...
Page 229 5-5. Using an external device Using the AUX port This port can be used to connect a portable audio device and lis- ten to it through the vehicle’s speakers. Press until “AUX” is displayed. Connecting a portable player P. 227 Operating portable audio devices connected to the audio system ■...
Page 230 ® 5-6. Using Bluetooth devices ® Bluetooth audio/phone ® The following can be performed using Bluetooth wireless com- munication: ® Bluetooth audio ■ ® The Bluetooth audio system enables you to enjoy music played on a portable player from the vehicle speakers via wireless com- munication.
Page 231 ® 5-6. Using Bluetooth devices Device registration/connection flow ® 1. Register a Bluetooth device to be used with the audio system ( P. 261) ® 2. Connect a registered Bluetooth device to be used ( P. 262, 263) 3. Set automatic connection of the device ( P.
Page 232 ® 5-6. Using Bluetooth devices Audio unit ® Bluetooth connection status If “BT” is not displayed, the ® Bluetooth audio/phone cannot be used. Display A message, name, number, etc. is displayed. Lower-case characters and spe- cial characters cannot be dis- played.
Page 233 ® 5-6. Using Bluetooth devices Microphone Vehicles without moon roof Vehicles with moon roof ® Menu list of the Bluetooth audio/phone To enter a menu, press and navigate menus by using First menu Second menu Third menu Operation details Register ®...
Page 234 ® 5-6. Using Bluetooth devices First menu Second menu Third menu Operation details Add a new num- “Add contacts” Register a speed “Add SD” dial Delete a number “Delete Call His- stored in the call “Phonebook” tory” history Delete a number “Delete contacts”...
Page 235 ® 5-6. Using Bluetooth devices Using the steering wheel switches The steering wheel switches can be used to operate a connected cellular phone or portable digital audio player (portable player). ® Operating a Bluetooth phone using the steering wheel switches Volume The voice guidance volume cannot be adjusted using these...
Page 236 ® 5-6. Using Bluetooth devices ® Registering a Bluetooth device ® Before using the Bluetooth audio/phone, it is necessary to reg- ® ister a Bluetooth device in the system. You can register up to 5 ® Bluetooth devices. ® How to register a Bluetooth device Press and select “Bluetooth...
Page 237 5-7. “SET UP” menu Using the “SET UP” menu (“Bluetooth” menu) ® Registering a Bluetooth device in the system allows the system to function. The following functions can be used for registered devices: Registering a portable player Select “BT Pairing” using ( P.
Page 238 5-7. “SET UP” menu Listing the registered portable players Select “List Audio” using . ( P. 258) The list of registered por- table players will be displayed. ● Connecting the registered portable player to the audio system Select the name of the portable player to be connected using Select “Select”...
Page 239 5-7. “SET UP” menu Changing the passkey Select “Passkey” using . ( P. 258) Input a 4 to 8-digit passkey using Input the number 1 digit at a time. When the entire number to be registered as a passkey has been input, press again.
Page 240 5-7. “SET UP” menu Displaying the device status Select “Bluetooth info” using . ( P. 258) ● Displaying the device name Select “Device Name” using ● Displaying the device address Select “Device Address” using : Bluetooth is a registered trademark of Bluetooth SIG, Inc. Setting the automatic connection confirmation display to on or If the “Display Setting”...
Page 241 5-7. “SET UP” menu Initialization Select “Initialize” using . ( P. 258) ● Initializing the sound settings Select “Sound setting” using and press (YES). For details about sound settings: P. 270 ● Initializing the device information Select “Car Device Info” using and press (YES).
Page 242 5-7. “SET UP” menu Using the “SET UP” menu (“Phone” menu) Adding a new phone number Select “Add contacts” using . ( P. 258) ● Transferring all contacts from the cellular phone Select “Overwrite all contacts” using and press (YES). ●...
Page 243 5-7. “SET UP” menu Deleting call histories Select “Delete Call History” using . ( P. 258) ● Deleting outgoing call history Select “Outgoing Calls” using Select the desired phone number using and press (YES). To delete all outgoing call history data, press (ALL) and then press (YES).
Page 244 5-7. “SET UP” menu ● Deleting missed call history Select “Missed calls” using Select the desired phone number using and press (YES). To delete all missed call history data, press (ALL) and then press (YES). ● Deleting a number from all call histories (Outgoing calls, Incoming calls and Missed calls) Select “All Calls”...
Page 245 5-7. “SET UP” menu Deleting a registered phone number Select “Delete contacts” using . ( P. 258) Select the desired phone number using and press (YES). To delete all of the registered phone numbers, select “All delete” using and press (YES).
Page 246 5-7. “SET UP” menu Setting ringtone Select “Ringtone” using . ( P. 258) Using , select a ringtone (1 - 3). To set the selected ringtone, press Transferring call histories Select “Transfer Histories” using and press (YES). Phone number ■ Up to 1000 names can be stored.
Page 247 ® 5-8. Bluetooth Audio ® Operating a Bluetooth enabled portable player Power Displays text message Volume Playback Select an album, fast-forward Playback/pause or reverse Search playback Repeat play Select a track Random playback Selecting an item COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 248 ® 5-8. Bluetooth Audio Selecting an album Press ) or ) to select the desired album. Scanning an album Press and hold until you hear a beep. The first 10 seconds of the first track in the each album will be played. When the desired album is reached, press again.
Page 249 ® 5-8. Bluetooth Audio Repeat play Pressing (RPT) changes the repeat play mode in the following order: Track repeat Album repeat : Available except when RDM (random playback) is selected Switching the display Press Track title and artist name are displayed on the display. To return to the previous display, press (BACK).
Page 250 ® 5-9. Bluetooth Phone Making a phone call To enter the “PHONE” mode, press the off-hook switch. Making a phone call ■ ● Dialing by selecting a name ● Speed dialing ● Dialing by entering the number ● Dialing from call histories Receiving a phone call ■...
Page 251 ® 5-9. Bluetooth Phone Dialing by selecting a name Select “Phonebook” using Select the desired name using and press the off-hook switch. By pressing (Add S. Dial) and then one of the speed dial but- tons (from ) while the desired name is selected, it can be registered as a speed dial.
Page 252 ® 5-9. Bluetooth Phone Dialing from call histories Select “All calls”, “Missed calls”, “Incoming calls” or “Outgoing calls” using Select the desired number using and press the off-hook switch. The following operations can be performed: ● Registering a number as a speed dial Press (Add S.
Page 253 ® 5-9. Bluetooth Phone Receiving a phone call Answering the phone Press the off-hook switch. Refusing a call Press the on-hook switch. Receiving a call when on another call Press the off-hook switch. Pressing the off-hook switch again returns you to the previous call. Adjusting the ringtone volume when receiving a call Change the ringtone volume using To decrease the volume: Turn...
Page 254 ® 5-9. Bluetooth Phone Speaking on the phone Transferring a call A call can be transferred between the cellular phone and system while dialing, receiving a call, or during a call. Use one of the following methods: a.Operate the cellular phone. Refer to the manual that comes with the cellular phone for the operation of the phone.
Page 255 ® 5-9. Bluetooth Phone When talking on the phone ■ Do not talk at the same time as the other party. ● Keep the volume of the received voice down. Otherwise, voice echo will ● increase. Automatic volume adjustment ■ When vehicle speed is 50 mph (80 km/h) or more, the volume automatically increases.
Page 256 ® 5-10. Bluetooth ® Bluetooth ® When using the Bluetooth audio system ■ In the following situations, the system may not function. ● ® • The portable player does not support Bluetooth • The cellular phone is located outside the service area ®...
Page 257 ® 5-10. Bluetooth CAUTION While driving ■ Do not operate the portable audio player, cellular phone or connect a device ® to the Bluetooth system. Caution regarding interference with electronic devices ■ ® Your audio unit is fitted with Bluetooth antennas.
Page 258 5-11.Basic Operations (Multimedia system) Multimedia system Operations such as listening to audio, using the hands-free phone and changing multimedia system settings are started by using the following buttons. Multimedia system operation buttons “AUDIO” button “SETUP” button Display the “Select Audio Source” Press this button to customize screen or audio top screen.
Page 259 5-11. Basic Operations (Multimedia system) Operating the touch screen By touching the screen with your finger, you can control the multime- dia system, etc. Drag ■ Touch the screen with your finger, and move the screen to the desired position. ●...
Page 260 5-11. Basic Operations (Multimedia system) Steering wheel audio switches Some audio features can be controlled using the switches on the steering wheel. Operation may differ depending on the type of multimedia sys- tem or navigation system. For details, refer to the manual pro- vided with the multimedia system or navigation system.
Page 261 5-11. Basic Operations (Multimedia system) USB port/AUX port Connect an iPod, USB memory device or portable audio player to the USB/AUX port as indicated below. Select “iPod”, “USB” or “AUX” on the audio source selection screen and the device can be operated via multimedia system.
Page 262 5-11. Basic Operations (Multimedia system) Basic audio operations Basic audio operations and functions common to each mode are explained in this section. Operating the multimedia system Press this knob to turn the mul- Turn this knob to select radio timedia system on and off, and station bands, tracks and files.
Page 263: Random Playback
5-11. Basic Operations (Multimedia system) Random playback Select to change on/off. Repeat play Select to change on/off. Using cellular phones ■ Interference may be heard through the multimedia system's speakers if a cel- lular phone is being used inside or close to the vehicle while the multimedia system is operating.
Page 264 5-12.Setup (Multimedia system) Setup menu You can adjust the multimedia system to your desired settings. Display “Setup” screen Press the “SETUP” button to display the “Setup” screen. Select to adjust the settings for operation sounds, screen ani- mation, etc. ( P. 290) Select to set the voice settings.
Page 265 The animation effect for the screen can be set to on/off. Select to delete personal data ( P. 291) Select to update program versions. For details, contact your Toyota dealer. Select to display the software information. Notices related to third party software used in this product are enlisted. (This includes instructions for obtaining such software, where applicable.)
Page 266 5-12. Setup (Multimedia system) Delete personal data Select “Delete Personal Data” on the “General Settings” screen. Select “Delete”. Check carefully beforehand, as data cannot be retrieved once deleted. A confirmation screen will be displayed. Select “Yes”. The following personal data will be deleted or changed to its default settings.
Page 267 5-12. Setup (Multimedia system) Audio settings Settings are available for adjusting the radio operation, cover art, etc. Screen for audio settings Press the “SETUP” button. Select “Audio” on the “Setup” screen. Number of Radio Presets Select the number of radio preset stations.
Page 268 5-12. Setup (Multimedia system) Automatic sound leveliser (ASL) Select “Automatic Sound Levelizer”. Select “High”, “Mid”, “Low” or “Off”. About Automatic Sound Leveliser (ASL) ■ ASL automatically adjusts the volume and tone quality according to the vehi- cle speed. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 269 5-12. Setup (Multimedia system) Display settings Settings are available for adjusting the contrast and brightness of the screen. Screen for display settings Press the “SETUP” button. Select “Display” on the “Setup” screen. Adjust screen contrast/bright- ness Adjust screen contrast/bright- ness of the rear view monitor camera Changes to day mode.
Page 270 5-12. Setup (Multimedia system) Voice settings This screen is used for guidance for voice command systems setting. Adjust the voice guidance vol- ume setting. voice recognition prompts “High”, “Low” or “Off”. Set the train voice recognition. Set the voice prompt interrupt on/off.
Page 271 5-13.Using the Multimedia system Selecting the audio source Switching between audio sources such as radio and CD are explained in this section. Changing audio source Press the “AUDIO” button to display the audio source selection screen. If the audio source selection screen is not displayed, press the “AUDIO” button again.
Page 272 5-13. Using the Multimedia system List screen operation When a list screen is displayed, use the appropriate buttons to scroll through the list. How to scroll : Select to scroll to the next or previous page. : If appears to the right of titles, the complete titles are too long for the display.
Page 273 5-13. Using the Multimedia system Selecting, fast-forwarding and reversing tracks/files/songs Selecting a track/file/song ■ Press the “ ” or “ ” button on “SEEK/TRACK” or turn the “TUNE/ SCROLL” knob to select the desired track/file/song number. To fast-forward or reverse, press and hold the “ ” or “ ” button on “SEEK/TRACK”.
Page 274 5-13. Using the Multimedia system Optimal use of the multimedia system On the “Sound Settings” screen, sound quality (Treble/Mid/ Bass), volume balance can be adjusted. How to adjust the sound settings and sound quality Select “-” or “+” to adjust 1 2 3 the treble, mid or bass to a level between -5 and 5.
Page 275 5-14.Using the radio (Multimedia system) Radio operation Select “AM” or “FM” on the audio source selection screen to begin listening to the radio. Audio control screen Pressing the “AUDIO” button displays the audio control screen from any screens of the selected source. Audio source selection screen appears Preset stations...
Page 276 5-14. Using the radio (Multimedia system) Setting station presets Search for desired stations by turning the “TUNE/SCROLL” knob or pressing the “ ” or “ ” button on “SEEK/TRACK”. Select “(add new)”. To change the preset station to a different one, select and hold the preset station.
Page 277 5-15.Playing an audio CD and MP3/WMA/AAC discs (Multimedia system) CD player operation Insert disc or select “CD” on the audio source selection screen with a disc inserted to begin listening to a CD. Audio control screen Pressing the “AUDIO” button displays the audio control screen from any screens of the selected source.
Page 278 Error messages ■ If an error message is displayed, refer to the following table and take the appropriate measures. If the problem is not rectified, take the vehicle to your Toyota dealer. Message Cause Correction procedures • The disc is dirty or •...
Page 279 5-15. Playing an audio CD and MP3/WMA/AAC discs (Multimedia system) MP3, WMA and AAC files ■ MP3 (MPEG Audio LAYER3) is a standard audio compression format. Files can be compressed to approximately 1/10 of their original size by using MP3 compression. WMA (Windows Media Audio) is a Microsoft audio compression format.
Page 280 5-15. Playing an audio CD and MP3/WMA/AAC discs (Multimedia system) AAC file compatibility ● • Compatible standards MPEG4/AAC-LC • Compatible sampling frequencies 11.025/12/16/22.05/24/32/44.1/48 (kHz) • Compatible bit rates 16-320 (kbps) Compatible channel modes: 1ch and 2ch Compatible media ● Media that can be used for MP3, WMA and AAC playback are CD-Rs and CD-RWs.
Page 281 5-15. Playing an audio CD and MP3/WMA/AAC discs (Multimedia system) ID3, WMA and AAC tags ● ID3 tags can be added to MP3 files, making it possible to record the track title, artist name, etc. The system is compatible with ID3 Ver. 1.0, 1.1, and Ver. 2.2, 2.3 ID3 tags. (The number of characters is based on ID3 Ver.
Page 282 5-15. Playing an audio CD and MP3/WMA/AAC discs (Multimedia system) NOTICE Discs and adapters that cannot be used ■ Do not use the following types of CDs. Also, do not use 8 cm (3 in.) CD adapters, Dual Discs or printable discs. Doing so may damage the CD player and/or the CD insert/eject function.
Page 283 5-16.Using an external device (Multimedia system) Listening to an iPod Connecting an iPod enables you to enjoy music from the vehicle speakers. Select “iPod” on the audio source selection screen. When the iPod connected to the system includes iPod video, the system can only output the sound by selecting the browse screen.
Page 284 5-16. Using an external device (Multimedia system) Selecting a play mode Select “Browse” on the screen. Select the desired play mode. Then select a song to begin using the selected play mode. Shuffle play Select to change on/off. Repeat play Select to change on/off.
Page 285 5-16. Using an external device (Multimedia system) About iPod ■ “Made for iPod” and “Made for iPhone” mean that an electronic accessory ● has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance stan- dards.
Page 286 5-16. Using an external device (Multimedia system) iPod problems ■ To resolve most problems encountered when using your iPod, disconnect your iPod from the vehicle iPod connection and reset it. For instructions on how to reset your iPod, refer to your iPod Owner's Manual. Error messages ■...
Page 287 5-16. Using an external device (Multimedia system) Compatible models ■ ® ® ® ® ® The following iPod , iPod nano , iPod classic , iPod touch and iPhone devices can be used with this system. Made for ● • iPod touch (5th generation) •...
Page 288 5-16. Using an external device (Multimedia system) Listening to a USB memory device Connecting a USB memory device enables you to enjoy music from the vehicle speakers. Touch “USB” on the audio source selection screen. Connecting a USB memory device P.
Page 289 5-16. Using an external device (Multimedia system) USB memory functions ■ Depending on the USB memory device that is connected to the system, the ● device itself may not be operable and certain functions may not be avail- able. If the device is inoperable or a function is unavailable due to a mal- function (as opposed to a system specification), disconnecting the device and reconnecting it may resolve the problem.
Page 290 5-16. Using an external device (Multimedia system) MP3 file compatibility ● • Compatible standards MP3 (MPEG1 AUDIO LAYERII, III, MPEG2 AUDIO LAYERII, III) • Compatible sampling frequencies MPEG1 AUDIO LAYERII, III: 32, 44.1, 48 (kHz) MPEG2 AUDIO LAYERII, III: 16, 22.05, 24 (kHz) •...
Page 291 5-16. Using an external device (Multimedia system) MP3, WMA and AAC playback ● • When a device containing MP3, WMA and AAC files is connected, all files in the USB memory device are checked. Once the file check is fin- ished, the first MP3, WMA and AAC file is played.
Page 292 5-16. Using an external device (Multimedia system) Using the AUX port To use the AUX port, connect a portable player, press the “AUDIO” button, then select “AUX” to display the audio control screen. Connecting a portable audio player P. 286 Operating portable audio players connected to the multimedia system ■...
Page 293 5-16. Using an external device (Multimedia system) Vehicle information This screen can be used to display the fuel consumption. “Trip Information” or “Past Record” screen Press “CAR” to display the “Trip Information” or “Past Record” screen. Fuel consumption Trip information ■...
Page 294 5-16. Using an external device (Multimedia system) Past record ■ If the “Past Record” screen does not appear, select “Past Record”. Previous fuel economy record Current fuel economy Best recorded fuel economy Update the past record data Reset the past record data “Trip Information”...
Page 295 ® 5-17.Connecting Bluetooth (Multimedia system) Preparations to use wireless communica- tion ® The following can be performed using Bluetooth wireless com- munication: A portable audio player can be operated and listened to via ■ multimedia system Hands-free phone calls can be made via a cellular phone ■...
Page 296 ® 5-17. Connecting Bluetooth (Multimedia system) CAUTION CAUTION: Radio Frequency Radiation Exposure ● This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Expo- sure Guidelines in Supplement C to OET65. This equipment has very low levels of RF energy that it deemed to comply without maximum permis- sive exposure evaluation (MPE).
Page 297 ® 5-17. Connecting Bluetooth (Multimedia system) Device registration/connection flow ® 1. Register the Bluetooth device to be used with multimedia system ( P. 324, 325, 326) ® 2. Connect the Bluetooth device to be used ( P. 329) To be used for audio To be used for hands-free phone ®...
Page 298 ® 5-17. Connecting Bluetooth (Multimedia system) Registering and connecting from the “Bluetooth* Setup” screen To display the screen shown below, press the “SETUP” button and select “Bluetooth ” on the “Setup” screen. Select to connect the device to be used with multimedia sys- tem.
Page 299 ® 5-17. Connecting Bluetooth (Multimedia system) ® Registering a Bluetooth audio player for the first time ® To use the Bluetooth Audio, it is necessary to register an audio player with the system. Once the player has been registered, it is possible to use the ®...
Page 300 ® 5-17. Connecting Bluetooth (Multimedia system) ® Registering a Bluetooth phone for the first time To use the hands-free system, it is necessary to register a ® Bluetooth phone with the system. Once the phone has been registered, it is possible to use the hands-free system.
Page 301 ® 5-17. Connecting Bluetooth (Multimedia system) ® Registering a Bluetooth device ® Bluetooth compatible phones (HFP) and portable audio players (AVP) can be registered simultaneously. You can register up to 5 ® Bluetooth devices. ® How to register a Bluetooth device Display the “Bluetooth* Setup”...
Page 302 ® 5-17. Connecting Bluetooth (Multimedia system) Check that this screen is dis- played when registration is complete. Select “OK” when the connection status changes from “Connect- ing...” to “Connected”. If an error message is displayed, follow the guidance on the screen to try again.
Page 303 ® 5-17. Connecting Bluetooth (Multimedia system) ® Deleting a Bluetooth device Display the “Bluetooth* Setup” screen. ( P. 323) : Bluetooth is a registered trademark of Bluetooth SIG, Inc. Select “Remove”. Select the desired device. A confirmation message will be displayed, select “Yes” to delete the device.
Page 304 ® 5-17. Connecting Bluetooth (Multimedia system) ® Connecting a Bluetooth device ® Up to 5 Bluetooth devices (Phones (HFP) and audio players (AVP)) can be registered. ® If more than 1 Bluetooth device has been registered, select which device to connect to. Press the “SETUP”...
Page 305 ® 5-17. Connecting Bluetooth (Multimedia system) Auto connection To turn auto connection mode on, set “Bluetooth* Power” to on. ( P. 334) When you register a phone, auto connection will be activated. Always ® set it to this mode and leave the Bluetooth phone in a place where a connection can be established.
Page 306 ® 5-17. Connecting Bluetooth (Multimedia system) ® Reconnecting a Bluetooth phone ■ If the system cannot connect due to poor signal strength with the engine switch in ACCESSORY or ON (IGNITION ON) mode, the system will auto- matically attempt to reconnect. If the phone is turned off, the system will not attempt to reconnect.
Page 307 ® 5-17. Connecting Bluetooth (Multimedia system) ® Displaying a Bluetooth device details You can confirm and change the registered device details. ® Bluetooth device registration status Display the “Bluetooth* Setup” screen. ( P. 323) : Bluetooth is a registered trademark of Bluetooth SIG, Inc. Select the device.
Page 308 ® 5-17. Connecting Bluetooth (Multimedia system) Changing connection method Select “Connect Audio Player from”. Select “Vehicle” or “Device”. “Vehicle”: Connect the multimedia system to the portable audio player. “Device”: Connect the portable audio player to the multimedia system COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 309 ® 5-17. Connecting Bluetooth (Multimedia system) ® Detailed Bluetooth system settings ® You can confirm and change the detailed Bluetooth settings. ® How to check and change detailed Bluetooth settings Display the “Bluetooth* Setup” screen. ( P. 323) Select “System Settings”. The following screen is displayed: ®...
Page 310 ® 5-17. Connecting Bluetooth (Multimedia system) Editing the Bluetooth* PIN ® You can change the PIN-code that is used to register your Bluetooth devices in the system. Select “Bluetooth* PIN”. Input a PIN-code, and select “OK”. : Bluetooth is a registered trademark of Bluetooth SIG, Inc. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 311 ® 5-18.Bluetooth Audio (Multimedia system) ® Listening to Bluetooth Audio ® The Bluetooth audio system enables the user to enjoy music played on a portable player from the vehicle speakers via wire- less communication. ® When a Bluetooth device cannot be connected, check the connec- tion status on the “Bluetooth* Audio”...
Page 312 ® 5-18. Bluetooth Audio (Multimedia system) Indicators Conditions Good Not connected Connection status Full Empty Battery charge ® Playing Bluetooth audio Select to Play/Pause. For details on “Bluetooth Audio” screen operation methods, refer to Basic Audio Operations. ( P. 287) For details on how to select a track or album, refer to selecting, fast- forwarding and reversing tracks/files/songs.
Page 313 ® 5-19.Bluetooth phone (Multimedia system) ® Using a Bluetooth Phone The hands-free system is a function that allows you to use your cellular phone without touching it. ® ® This system supports Bluetooth . Bluetooth is a wireless data system that allows the cellular phone to wirelessly connect to the hands-free system and make/receive calls.
Page 314 ® 5-19. Bluetooth phone (Multimedia system) Telephone switch ( P. 354) ■ Microphone ■ Vehicles without moon roof Vehicles with moon roof The vehicle’s built in microphone is used when talking on the phone. The person you are speaking to can be heard from the front speak- ers.
Page 315 ® 5-19. Bluetooth phone (Multimedia system) Indicators Conditions Good Not connected Connection status Full Empty Battery charge “Rm”: Roaming area Call area Excellent Poor Signal strength COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 316 ® 5-19. Bluetooth phone (Multimedia system) Making a call ® Once a Bluetooth phone is registered, you can make a call using the following procedure: Dialing Display the phone screen. ( P. 338) Select the “Dial Pad” tab and enter a phone number. To delete the input phone number, select For the first digit, you can enter “+”...
Page 317 ® 5-19. Bluetooth phone (Multimedia system) Press the switch on the steering wheel. If the phonebook is empty, a message will be displayed. ® For a PBAP compatible Bluetooth phone and “Automatic Contact/ History Transfer” is off Select the desired item. Select to transfer new con- tacts from a cellular phone, select “Always”...
Page 318 ® 5-19. Bluetooth phone (Multimedia system) Calling using favorites list You can make a call using numbers registered in the contact. Display the phone screen. ( P. 338) Select “Favorites” tab. Select the desired number to make a call. Dialing from call history You can make a call using the call history, which has the 3 functions below.
Page 319 ® 5-19. Bluetooth phone (Multimedia system) Receiving a call When a call is received, the following screen is displayed together with a sound. To answer the phone Press the switch on the steer- ing wheel or select To refuse a call Press the switch on the steering wheel or select To adjust the incoming call volume...
Page 320 ® 5-19. Bluetooth phone (Multimedia system) Speaking on the phone The following screen is displayed when speaking on the phone. To adjust the call volume Select “-” or “+”. You can also adjust the volume using the steering switches or the volume knob. To prevent the other party from hearing your voice Select “Mute”.
Page 321 ® 5-19. Bluetooth phone (Multimedia system) Release Tones ■ A continuous tone signal is a character string that consists of numbers and ● the characters p or w. (e.g.056133w0123p#1 ) When the “p” pause tone is used, the tone data up until the next pause tone ●...
Page 322 ® 5-19. Bluetooth phone (Multimedia system) To transfer a call Select “Handset Mode” to on from a hands-free call to a cellular phone call. Select “Handset Mode” to off from a cellular phone call to a hands-free call. Transmit volume setting Select “Transmit Volume”.
Page 323 ® 5-19. Bluetooth phone (Multimedia system) Transferring calls ■ If you transfer from the cellular phone to hands-free, the hands-free screen ● will be displayed, and you can operate the system using the screen. Transfer method and operation may vary according to the cellular phone ●...
Page 324 ® 5-19. Bluetooth phone (Multimedia system) ® Bluetooth phone message function Received messages can be forwarded from the connected ® Bluetooth phone, enabling checking and replying using the multimedia system. ® Depending on the type of Bluetooth phone connected, received messages may not be transferred to the message inbox.
Page 325 ® 5-19. Bluetooth phone (Multimedia system) Receiving a message ■ Depending on the cellular phone used for receiving messages, or its regis- ● tration status with the navigation system, some information may not be dis- played. The pop up screen is separately available for incoming e-mail and SMS/ ●...
Page 326 ® 5-19. Bluetooth phone (Multimedia system) Checking the messages Display the message inbox screen. ( P. 349) Select the desired message from the list. Check that the message is displayed. E-mails: Select “Mark Unread” or “Mark Read” to mark mail unread or read on the message inbox screen.
Page 327 ® 5-19. Bluetooth phone (Multimedia system) Check the messages ■ ® Depending on the type of Bluetooth phone being connected, it may be nec- ● essary to perform additional steps on the phone. ® Messages are displayed in the appropriate connected Bluetooth phone’s ●...
Page 328 ® 5-19. Bluetooth phone (Multimedia system) Calling the message sender Calls can be made to an e-mail/SMS/MMS message sender's phone number. Display the message inbox screen. ( P. 349) Select the desired message. Select Check that the “Call” screen is displayed. Calling from a number within a message ■...
Page 329 ® 5-19. Bluetooth phone (Multimedia system) Using the steering wheel switches The steering wheel switches can be used to operate a connected cellular phone. Operating a telephone using the steering wheel switches Steering wheel switches on the right hand side ■...
Page 330 ® 5-19. Bluetooth phone (Multimedia system) ® Bluetooth phone settings You can adjust the hands-free system to your desired settings. “Phone/Message Settings” screen To display the screen shown below, press the “SETUP” button, and select “Phone” on the “Setup” screen. Set the phone connection ( P.
Page 331 ® 5-19. Bluetooth phone (Multimedia system) Sound setting Display the “Phone/Message Settings” screen. ( P. 355) Select “Sound Settings” on the “Phone/Message Settings” screen. Set the desired ringtone. Adjust the ringtone volume. Adjust the message readout volume. Set the desired incoming SMS/MMS tone.
Page 332 ® 5-19. Bluetooth phone (Multimedia system) Contact/Call History Settings ® The contact can be transferred from a Bluetooth phone to the sys- tem. The contact also can be added, edited and deleted. The call history can be deleted and contact and favorites can be changed.
Page 333 ® 5-19. Bluetooth phone (Multimedia system) Update contacts from phone Operation methods differ between PBAP compatible and PBAP ® incompatible but OPP compatible Bluetooth phones. If your cellular phone is neither PBAP nor OPP compatible, the con- tacts cannot be transferred. ®...
Page 334 ® 5-19. Bluetooth phone (Multimedia system) ® For PBAP Incompatible but OPP compatible Bluetooth ■ Phones Select “Update Contacts from Phone”. ® Transfer the contact data to the system using a Bluetooth phone. This operation may be unnecessary depending on the type of cellular phone.
Page 335 ® 5-19. Bluetooth phone (Multimedia system) Registering a new contact to the contact list New contact data can be registered. Up to 4 numbers per person can ® be registered. For PBAP compatible Bluetooth phones, this function is available when “Automatic Contact/History Transfer” is set to off. ( P.
Page 336 ® 5-19. Bluetooth phone (Multimedia system) Editing the contact data ® For PBAP compatible Bluetooth phones, this function is available when “Automatic Contact/History Transfer” is set to off. ( P. 357) Select “Edit Contact”. Select the desired contact. Select corresponding to the desired name or number. For editing the name Follow the steps in “Registering a new contact to the contacts list”...
Page 337 ® 5-19. Bluetooth phone (Multimedia system) Deleting the contact data ® For PBAP compatible Bluetooth phones, this function is available when “Automatic Contact/History Transfer” is set to off. ( P. 357) Select “Delete Contacts”. Select the desired contact and select “Delete”. Select “Yes”...
Page 338 ® 5-19. Bluetooth phone (Multimedia system) When 15 contacts have already been registered to the favorites list When 15 contacts have already been registered to the favorites list, a registered contact needs to be replaced. Select “Yes” when the confirmation screen appears to replace a contact.
Page 339 ® 5-19. Bluetooth phone (Multimedia system) Deleting the contacts in the favorites list ■ Select “Remove Favorite”. Select the desired contacts and select “Remove”. Select “Yes” when the confirmation screen appears. Check that a confirmation screen is displayed when the opera- tion is complete.
Page 340 ® 5-19. Bluetooth phone (Multimedia system) Message Settings Display the “Phone/Message Settings” screen. ( P. 355) Select “Messaging Settings”. Select the desired item to be set. automatic message transfer on/off. automatic message readout on/off. Set the SMS/MMS notifica- tion popup on/off. Set the e-mail notification popup on/off.
Page 341 ® 5-19. Bluetooth phone (Multimedia system) Displaying the “Messaging Settings” screen in a different way ■ Display the phone screen. ( P. 338) Select Select “Settings”. Phone Display Settings Display the “Phone/Message Settings” screen. ( P. 355) Select “Phone Display Settings”. Select the desired item to be set.
Page 342 The connected device may not be a compatible Bluetooth cellular phone. For a list of specific devices which operation has been confirmed on this system, check with your Toyota dealer or the following web- site: http://www.toyota.com/entune.html The Bluetooth version of the connected cellular phone may be older than the specified version.
Page 343 ® 5-19. Bluetooth phone (Multimedia system) When registering/connecting a cellular phone A cellular phone cannot be registered. An incorrect passcode was entered on the cellular phone. Enter the correct passcode on the cellular phone. The registration operation has not been completed on the cellular phone side.
Page 344 For a list of specific devices which operation has been confirmed on this system, check with your Toyota dealer or the following web- site: http://www.toyota.com/entune.html Automatic phonebook transfer function on this system is set to off.
Page 345 ® 5-19. Bluetooth phone (Multimedia system) In other situations Even though all conceivable measures have been taken, the symptom sta- tus does not change. The cellular phone is not close enough to this system. Bring the cellular phone closer to this system. The cellular phone is the most likely cause of the symptom.
Page 346 ® 5-20.Bluetooth (Multimedia system) ® Bluetooth ® When using the Bluetooth audio system ■ In the following conditions, the system may not function. ● • If the portable audio player is turned off • If the portable audio player is not connected •...
Page 347 ® 5-20. Bluetooth (Multimedia system) ® Bluetooth antenna ■ The antenna is built into the display. If the portable audio player is behind the seat or in the glove box or console box, or is touching or covered by metal objects, the connection status may deteriorate.
Page 348 ® 5-20. Bluetooth (Multimedia system) Compatible models ■ ® The Bluetooth audio system supports portable audio players with the follow- ing specifications ® Bluetooth specifications: ● Ver. 2.0, or higher (Recommended: Ver. 3.0+EDR or higher) Profiles: ● • A2DP (Advanced Audio Distribution Profile) Ver. 1.0, or higher (Recommended: Ver.
Page 349 ® 5-20. Bluetooth (Multimedia system) Certification ■ NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 350 ® 5-20. Bluetooth (Multimedia system) CAUTION While driving ■ Do not use the portable audio player, cellular phone or connect a device to ® the Bluetooth system. Caution regarding interference with electronic devices ■ ® Your audio unit is fitted with Bluetooth antennas.
Page 351 5-21.Using the voice command system (Multimedia system) Voice command system The voice command system enables the hands-free system to be operated using voice commands. Operations of the voice command system can be performed by selecting the menu corresponding to each function on the screen.
Page 352 5-21. Using the voice command system (Multimedia system) Casual speech recognization Due to natural language speech recognition technology, this system enables recognition of a command when spoken naturally. However, the system cannot recognize every variation of each command. In some situations, it is possible to omit the command for the proce- dure and directly state the desired operation.
Page 353 5-21. Using the voice command system (Multimedia system) Command list Some recognizable voice commands and their actions are shown below as examples. Basic Command Action Prompts voice guidance to offer examples of com- “Help” mands or operation methods “Go Back” Returns to the previous screen Phone Command...
Page 354 6-1. Using the air conditioning system and defogger Manual air conditioning system Air conditioning controls Heater Air conditioning system Adjusting the temperature setting ■ Heater To adjust the temperature setting, turn the dial clockwise to increase the temperature. Air conditioning system To adjust the temperature setting, turn the dial clockwise (warm) or counterclockwise (cool).
Page 355 6-1. Using the air conditioning system and defogger Other functions Switching between outside air and recirculated air modes ■ Press The mode switches between outside air mode (indicator off) and recir- culated air mode (indicator on) each time is pressed. Defogging the windshield ■...
Page 356 6-1. Using the air conditioning system and defogger Air outlets Location of air outlets ■ The air outlets and air volume changes according selected airflow mode. : Some models Adjusting the position of and opening and closing the air out- ■...
Page 357 6-1. Using the air conditioning system and defogger Front side outlets Direct air flow to the left or right, up or down. Close the vent Sliding the knob to the most outer position. Open the vent COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 358 6-1. Using the air conditioning system and defogger For quick cooling (vehicles with air conditioning system) ■ Turn the dial to the “MAX A/C” position and select the recirculated air mode. Fogging up of the windows ■ Vehicles with the button: The windows will easily fog up when the ●...
Page 359 6-1. Using the air conditioning system and defogger CAUTION To prevent the windshield from fogging up ■ Do not set the air outlet selector dial to during cool air operation in ● extremely humid weather. The difference between the temperature of the outside air and that of the windshield can cause the outer surface of the windshield to fog up, blocking your vision.
Page 360 6-1. Using the air conditioning system and defogger Automatic air conditioning system Air outlets and fan speed are automatically adjusted according to the temperature setting. Air conditioning controls Adjusting the temperature setting ■ To adjust the temperature setting, turn clockwise to increase the temperature and turn counterclockwise to decrease the temperature.
Page 361 6-1. Using the air conditioning system and defogger Fan speed setting ■ Press “ ” on to increase the fan speed. Press “ ” on to decrease the fan speed. Change the airflow mode ■ To change the airflow, press “ ” or “ ” on The air outlets used are switched each time either side of the button is pressed.
Page 362 6-1. Using the air conditioning system and defogger Using automatic mode Press The dehumidification function begins to operate. Air outlets and fan speed are automatically adjusted according to the temperature set- ting. Adjust the temperature setting. Automatic mode indicator ■ If the fan speed setting or air flow modes are operated, the auto- matic mode indicator goes off.
Page 363 6-1. Using the air conditioning system and defogger Defogging the rear window and outside rear view mirrors ■ Defoggers are used to defog the rear window, and to remove rain- drops, dew and frost from the outside rear view mirrors. Press The defoggers will automatically turn off after a period of time.
Page 364 6-1. Using the air conditioning system and defogger Air outlets Location of air outlets ■ The air outlets and air volume changes according selected airflow mode. : Some models Adjusting the position of and opening and closing the air out- ■...
Page 365 6-1. Using the air conditioning system and defogger Close the vent Sliding the knob to the most outer position. Open the vent Operation of the air conditioning system in Eco drive mode (if equipped) ■ In Eco drive mode, the air conditioning system is controlled as follows to pri- oritize fuel efficiency: Engine speed controlled to restrict heating/cooling capacity.
Page 366 6-1. Using the air conditioning system and defogger Fogging up of the windows ■ The windows will easily fog up when the humidity in the vehicle is high. ● Turning on will dehumidify the air from the outlets and defog the wind- shield effectively.
Page 367 Air conditioning filter ■ P. 461 Customization that can be configured at Toyota dealer ■ Settings (e.g. air conditioning setting) can be changed. (Customizable features P. 570) COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 368 6-1. Using the air conditioning system and defogger CAUTION To prevent the windshield from fogging up ■ Do not use during cool air operation in extremely humid weather. ● The difference between the temperature of the outside air and that of the windshield can cause the outer surface of the windshield to fog up, block- ing your vision.
Page 369 6-2. Using the interior lights Interior lights list Front interior light/personal lights ( P. 396) Rear interior light ( P. 397) Engine switch light (vehicles with a smart key system) COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 370 6-2. Using the interior lights Front interior light/personal lights Front interior light ■ Type A Type B Door position Personal lights ■ Type A Type B On/off When a light is on due to its door link switch, the light will not turn off even if the lens is pressed.
Page 371 6-2. Using the interior lights Rear interior light Door position Illuminated entry system ■ Vehicles without a smart key system When the interior light switch is in the door position, the interior light automat- ically turns on/off according to the engine switch position, whether the doors are locked/unlocked and whether the doors are open/closed.
Page 372 6-3. Using the storage features List of storage features Glove box ( P. 399) Console box ( P. 399) Bottle holders ( P. 400) Cup holders ( P. 401) CAUTION Items that should not be left in the storage spaces ■...
Page 373 6-3. Using the storage features Glove box Pull up the lever to open the glove box. Console box Console box Lift the lid while pulling up the knob on the right side. Upper level box Lift the lid while pulling up the knob on the left side.
Page 374: Bottle Holders
6-3. Using the storage features Bottle holders Front ■ Rear ■ When using the holder as a bottle holder ■ When storing a bottle, close the cap. ● The bottle may not be stored depending on its size or shape. ●...
Page 375 6-3. Using the storage features Cup holders Front ■ Rear ■ With console box With armrest (if equipped) Pull the lid to open. Pull the armrest down. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 376 6-3. Using the storage features Adjusting the size of the cup holder (front) ■ Remove the cup holder insert. Change the cup holder insert position. Removing the cup holder insert (front) ■ The cup holder insert may be removed for cleaning.
Page 377 6-4. Other interior features Other interior features Sun visors To set the visor in the forward position, flip it down. To set the visor in the side posi- tion, flip down, unhook, and swing it to the side. Vanity mirrors Slide the cover.
Page 378 When the vehicle is stopped, or moving at low speeds (less than 9 mph [15 ● km/h]). When the outside temperature has changed suddenly (at the entrance/exit ● of a garage, tunnel, etc.) When “-- F” is displayed ■ The system may be malfunctioning. Take your vehicle to your Toyota dealer. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 379: Power Outlet
6-4. Other interior features Power outlet Please use as a power supply for electronic goods that use less than 12 VDC/10 A (power consumption of 120 W). Open the lid. The power outlet can be used when ■ Vehicles without a smart key system The engine switch is in the “ACC”...
Page 380: Assist Grips
6-4. Other interior features Assist grips An assist grip installed on the ceil- ing can be used to support your body while sitting on the seat. CAUTION Do not use the assist grip when getting in or out of the vehicle or rising from your seat.
Page 381 6-4. Other interior features Compass The compass on the inside rear view mirror indicates the direc- tion in which the vehicle is heading. Operation To turn the compass on or off, press and hold “AUTO” for 3 sec- onds. Displays and directions Display Direction North...
Page 382 6-4. Other interior features Calibrating the compass The direction display deviates from the true direction determined by the earth’s magnetic field. The amount of deviation varies according to the geographic position of the vehicle. If you cross over a map boundary shown in illustration, the compass will deviate.
Page 383 6-4. Other interior features Circling calibration ■ Stop the vehicle in a place where it is safe to drive in a circle. Press and hold “AUTO” for 9 seconds. C appears on the compass dis- play. Drive the vehicle at 5 mph (8 km/h) or less in a circle until a direction is displayed.
Page 384 6-4. Other interior features Conditions unfavorable to correct operation ■ The compass may not show the correct direction in the following conditions: The vehicle is stopped immediately after turning. ● The vehicle is on an inclined surface. ● The vehicle is in a place where the earth's magnetic field is subject to inter- ●...
Page 385 6-4. Other interior features Seat heaters Press the switch. High temperature Low temperature The indicator light comes on when the switch is on. The seat heaters can be used when ■ Vehicles without a smart key system The engine switch is in the “ON” position. Vehicles with a smart key system The engine switch is in IGNITION ON mode.
Page 386 6-4. Other interior features CAUTION Burns ■ Use caution when seating the following persons in a seat with the seat ● heater on to avoid the possibility of burns: • Babies, small children, the elderly, the sick and the physically chal- lenged •...
Page 387 7-1. Maintenance and care Cleaning and protecting the vehicle exterior Perform the following to protect the vehicle and maintain it in prime condition: ● Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust.
Page 388 7-1. Maintenance and care When using a car wash (vehicles with a smart key system) ■ If the door handle becomes wet while the electronic key is within the effective range, the door may lock and unlock repeatedly. In that case, follow the fol- lowing correction procedures to wash the vehicle: Place the key in a position 6 ft.
Page 389 7-1. Maintenance and care NOTICE To prevent paint deterioration and corrosion on the body and compo- ■ nents (aluminum wheels etc.) Wash the vehicle immediately in the following cases: ● • After driving near the sea coast • After driving on salted roads •...
Page 390 7-1. Maintenance and care Cleaning and protecting the vehicle interior The following procedures will help protect your vehicle’s interior and keep it in top condition: Protecting the vehicle interior Remove dirt and dust using a vacuum cleaner. Wipe dirty surfaces with a cloth dampened with lukewarm water.
Page 391 7-1. Maintenance and care Shampooing the carpets ■ There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam. Rub in overlapping circles. Do not use water. Wipe dirty surfaces and let them dry. Excellent results are obtained by keep- ing the carpet as dry as possible.
Page 392 7-1. Maintenance and care NOTICE Cleaning detergents ■ Do not use the following types of detergent, as they may discolor the vehi- ● cle interior or cause streaks or damage to painted surfaces: • Non-seat portions: Organic substances such as benzene or gasoline, alkaline or acidic solutions, dye, and bleach •...
Page 393 Toyota recommends the following main- tenance: General maintenance General maintenance should be performed on a daily basis. This can be done by yourself or by a Toyota dealer. Scheduled maintenance Scheduled maintenance should be performed at specified intervals according to the maintenance schedule.
Page 394 Repair and replacement ■ It is recommended that genuine Toyota parts be used for repairs to ensure performance of each system. If non-Toyota parts are used in replacement or if a repair shop other than a Toyota dealer performs repairs, confirm the war- ranty coverage.
Page 395 7-2. Maintenance CAUTION If your vehicle is not properly maintained ■ Improper maintenance could result in serious damage to the vehicle and possible death or serious injury. Handling of the battery ■ Engine exhaust, some of its constituents, and a wide variety of automobile ●...
Page 396 “Owner’s Warranty Information Booklet” or “Owner’s Manual Supplement/Sched- uled Maintenance Guide”. It is recommended that any problem you notice should be brought to the attention of your Toyota dealer or qualified service shop for advice. Engine compartment...
Page 397 7-2. Maintenance Vehicle interior Items Check points • The accelerator pedal should Accelerator pedal move smoothly (without uneven pedal effort or catching). Automatic transmission or continu- • When parked on a slope and the ously variable transmission “Park” shift lever is in P, is the vehicle mechanism securely stopped? •...
Page 398 7-2. Maintenance Items Check points • Do the head restraints move Head restraints smoothly and lock securely? • Do the indicators and buzzers Indicators/buzzers function properly? Lights • Do all the lights come on? • Moves smoothly? • When parked on a slope and the Parking brake parking brake is on, is the vehicle securely stopped?
Page 399 7-2. Maintenance Vehicle exterior Items Check points • Do doors/trunk operate Doors/trunk smoothly? • Does the engine hood lock system Engine hood work properly? • There should not be any signs of Fluid leaks fluid leakage after the vehicle has been parked.
Page 400 The OBD system determines that a problem exists somewhere in the emission control system. Your vehicle may not pass the I/M test and may need to be repaired. Contact your Toyota dealer to service the vehicle. Your vehicle may not pass the I/M test in the following situations: ●...
Page 401 J1703 brake fluid Brake fluid level ( P. 442) • Rag or paper towel • Funnel (used only for adding brake fluid) • “Toyota Super Long Life Coolant” or a similar high quality ethylene glycol-based non-silicate, non- amine, non-nitrite and non-borate...
Page 402 7-3. Do-it-yourself maintenance Items Parts and tools • Bulb with same number and watt- age rating as original Light bulbs ( P. 469) • Phillips-head screwdriver • Flathead screwdriver • Wrench Radiator/condenser ( P. 442) • Tire pressure gauge Tire inflation pressure ( P. 456) •...
Page 403 7-3. Do-it-yourself maintenance CAUTION When working near the electric cooling fan or radiator grille ■ Vehicles without a smart key system: Be sure the engine switch is off. With the engine switch in the “ON” position, the electric cooling fan may automat- ically start to run if the air conditioning is on and/or the coolant temperature is high.
Page 404 7-3. Do-it-yourself maintenance Hood Release the lock from the inside of the vehicle to open the hood. Pull the hood lock release lever. The hood will pop up slightly. Pull up the auxiliary catch lever and lift the hood. Hold the hood open by inserting the support rod into the slot.
Page 405 7-3. Do-it-yourself maintenance CAUTION Pre-driving check ■ Check that the hood is fully closed and locked. If the hood is not locked properly, it may open while the vehicle is in motion and cause an accident, which may result in death or serious injury. After installing the support rod into the slot ■...
Page 406 7-3. Do-it-yourself maintenance Positioning a floor jack When using a floor jack, follow the instructions in the manual provided with the jack and perform the operation safely. When raising your vehicle with a floor jack, position the jack cor- rectly. Improper placement may damage your vehicle or cause injury.
Page 407 7-3. Do-it-yourself maintenance Set the jack attachment on the floor jack and position the jack. Before raising vehicle, make sure that the floor jack is positioned so that the protru- sion on the jack attachment fits securely into the hole of the jack point.
Page 408 7-3. Do-it-yourself maintenance Engine compartment Washer fluid tank ( P. 447) Battery ( P. 444) Engine oil filler cap Fuse box ( P. 466) ( P. 438) Electric cooling fan Engine oil level dipstick Engine coolant reservoir ( P. 436) ( P.
Page 409 7-3. Do-it-yourself maintenance Engine oil With the engine at operating temperature and turned off, check the oil level on the dipstick. Checking the engine oil ■ Park the vehicle on level ground. After warming up the engine and turning it off, wait more than 5 minutes for the oil to drain back into the bottom of the engine.
Page 410 7-3. Do-it-yourself maintenance Holding a rag under the end, pull the dipstick out and check the oil level. Normal Excessive Flat dipstick Non-flat dipstick The shape of the dipstick may differ depending on the type of vehicle or engine. Wipe the dipstick and reinsert it fully. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 411 7-3. Do-it-yourself maintenance Adding engine oil ■ If the oil level is below or near the low level mark, add engine oil of the same type as that already in the engine. Make sure to check the oil type and prepare the items needed before adding oil.
Page 412 Call your Toyota dealer, service station or auto parts store for information concerning recycling or disposal. Do not leave used engine oil within the reach of children.
Page 413: Engine Coolant
If the coolant level drops within a short time of replenishing ■ Visually check the radiator, hoses, engine coolant reservoir caps, drain cock and water pump. If you cannot find a leak, have your Toyota dealer test the cap and check for leaks in the cooling system. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 414 7-3. Do-it-yourself maintenance CAUTION When the engine is hot ■ Do not remove the engine coolant reservoir cap or the radiator cap. ( P. 538) The cooling system may be under pressure and may spray hot coolant if the cap is removed, causing serious injuries, such as burns. NOTICE When adding coolant ■...
Page 415 Check the radiator and condenser and clear away any foreign objects. If either of the above parts is extremely dirty or you are not sure of their condition, have your vehicle inspected by your Toyota dealer. CAUTION When the engine is hot ■...
Page 416 However, if the reservoir needs frequent refilling, there may be a serious problem. Have the vehicle inspected at your Toyota dealer as soon as pos- sible. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 417 Make sure to turn off the engine before disconnect the battery. Take extra care when connecting the battery if the engine switch mode prior to discharge is unknown. If the system will not start even after multiple attempts, contact your Toyota dealer. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 418 7-3. Do-it-yourself maintenance CAUTION Chemicals in the battery ■ Batteries contain poisonous and corrosive sulfuric acid and may produce hydrogen gas which is flammable and explosive. To reduce the risk of death or serious injury, take the following precautions while working on or near the battery: Do not cause sparks by touching the battery terminals with tools.
Page 419 7-3. Do-it-yourself maintenance NOTICE When recharging the battery ■ Never recharge the battery while the engine is running. Also, be sure all accessories are turned off. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 420 7-3. Do-it-yourself maintenance Washer fluid Add washer fluid in the following situations: ● A washer does not work. ● Vehicles with a drive monitor display: The low windshield washer fluid warning light (if equipped) comes on. ( P. 493) ● Vehicles with a multi-informa- tion display: The warning mes- sage (if equipped) appears on the multi-information display.
Page 421 Check spare tire condition and pressure if not rotated. Tire rotation Rotate the tires in the order shown. To equalize tire wear and extend tire life, Toyota recommends that tire rotation is carried out at the Front same interval as tire inspection. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 422 ID codes must be registered in the tire pressure warning computer and the tire pressure warning system must be initialized. Have tire pressure warning valves and transmitter ID codes registered by your Toyota dealer. ( P. 451) ◆ Initializing the tire pressure warning system The tire pressure warning system must be initialized in the fol- ■...
Page 423 7-3. Do-it-yourself maintenance How to initialize the tire pressure warning system ■ Park the vehicle in a safe place and turn the engine switch off. Initialization cannot be performed while the vehicle is moving. Adjust the tire inflation pressure to the specified cold tire inflation pressure level.
Page 424 A tire goes flat repeatedly or cannot be properly repaired due to the size ● or location of a cut or other damage If you are not sure, consult with your Toyota dealer. Replacing tires and wheels (vehicles with a tire pressure warning ■...
Page 425 7-3. Do-it-yourself maintenance Maximum load of tire ■ Check that the maximum load of the replacement tire is greater than 1/2 of the Gross Axle Weight Ratings (GAWR) of either the front axle or the rear axle, whichever is greater. For the GAWR, see the Certification Label.
Page 426 If repeated attempts to record tire inflation pressure settings are unsuccessful, have the vehicle inspected by your Toyota dealer. When operating the tire pressure warning reset switch, the tire pressure ●...
Page 427 Do not mix tires of different makes, models or tread patterns. ● Also, do not mix tires of remarkably different treadwear. Do not use tire sizes other than those recommended by Toyota. ● Do not mix differently constructed tires (radial, bias-belted or bias-ply ●...
Page 428 When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and transmitter when replacing the tire.
Page 429 7-3. Do-it-yourself maintenance Tire inflation pressure Tire inflation pressure The recommended cold tire infla- tion pressure and tire size are dis- played on the tire and loading information label. ( P. 552) COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 430 Driving with incorrect tire inflation pressure may result in the following: Reduced fuel efficiency ● Reduced driving comfort and tire life ● Reduced safety ● Damage to the drive train ● If a tire needs frequent inflating, have it checked by your Toyota dealer. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 431 7-3. Do-it-yourself maintenance Instructions for checking tire inflation pressure ■ When checking tire inflation pressure, observe the following: Check only when the tires are cold. ● If your vehicle has been parked for at least 3 hours or has not been driven for more than 1 mile or 1.5 km, you will get an accurate cold tire inflation pressure reading.
Page 432 ● Used wheels ● Bent wheels that have been straightened Aluminum wheel precautions (if equipped) ● Use only Toyota wheel nuts and wrenches designed for use with your aluminum wheels. ● When rotating, repairing or changing your tires, check that the wheel nuts are still tight after driving 1000 miles (1600 km).
Page 433 Because tire repair or replacement may affect the tire pressure warn- ● ing valves and transmitters, make sure to have tires serviced by your Toyota dealer or other qualified service shop. In addition, make sure to purchase your tire pressure warning valves and transmitters at your Toyota dealer.
Page 434 7-3. Do-it-yourself maintenance Air conditioning filter The air conditioning filter must be changed regularly to maintain air conditioning efficiency. Removal method Turn the engine switch off. Open the glove box. Slide off the damper. Push in the glove box on the vehicle’s outer side to discon- nect the claws.
Page 435 7-3. Do-it-yourself maintenance Replacement method ■ Remove the air conditioning filter and replace it with a new one. The “ UP” marks shown on the fil- ter should be pointing up. Checking interval ■ Inspect and replace the air conditioning filter according to the maintenance schedule.
Page 436 7-3. Do-it-yourself maintenance Wireless remote control/electronic key bat- tery Replace the battery with a new one if it is depleted. You will need the following items: ● Flathead screwdriver ● Small flathead screwdriver ● Lithium battery CR2016 (vehicles without a smart key system), or CR2032 (vehicles with a smart key system) Replacing the battery Vehicles without a smart key system...
Page 437 7-3. Do-it-yourself maintenance Open the case cover using a coin protected with tape etc. and remove the depleted bat- tery using a small flathead screwdriver. Insert a new battery with the “+” terminal facing up. Vehicles with a smart key system Take out the mechanical key.
Page 438 Use a CR2016 (vehicles without a smart key system) or CR2032 (vehicles ■ with a smart key system) lithium battery Batteries can be purchased at your Toyota dealer, local electrical appliance ● shops or camera stores. Replace only with the same or equivalent type recommended by the manu- ●...
Page 439 7-3. Do-it-yourself maintenance Checking and replacing fuses If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as nec- essary. Turn the engine switch off. Open the fuse box cover. Engine compartment Push the tab in and lift the lid off.
Page 440 7-3. Do-it-yourself maintenance Check if the fuse is blown. Normal fuse Blown fuse Replace the blown fuse with a new fuse of an appropriate amperage rat- ing. The amperage rating can be found on the fuse box lid. Type A Type B Type C COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 441 If the lights do not turn on even after the fuse has been replaced, a bulb may ● need replacement. ( P. 469) If the replaced fuse blows again, have the vehicle inspected by your Toyota ● dealer. If there is an overload in a circuit ■...
Page 442 Light bulbs You may replace the following bulbs yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs, contact your Toyota dealer.
Page 443 7-3. Do-it-yourself maintenance Rear ■ Back-up lights Rear turn signal lights Stop/tail/rear side marker lights License plate lights Replacing light bulbs Headlight high beams ■ Turn the bulb base counter- clockwise. Pull the bulb out while press- ing the lock release of the connector.
Page 444 7-3. Do-it-yourself maintenance Replace the light bulb, and install the bulb base. Align the 3 tabs on the light bulb with the mounting and insert. Turn and secure the bulb base. Shake the bulb base gently to check that it is not loose, turn the headlights on once and visu- ally confirm that no light is leak- ing through the mounting.
Page 445 7-3. Do-it-yourself maintenance Front fog lights (if equipped) ■ Remove the fender liner bolts and clip. Partly remove the fender liner. Unplug the connector while depressing the lock release. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 446 7-3. Do-it-yourself maintenance Turn the bulb base counter- clockwise. Install a new light bulb. Align the 3 tabs on the light bulb with the mounting and insert. Turn clockwise and secure the bulb base. Install the connector. Shake the connector gently to check that it is not loose, turn the front fog lights on once and visually confirm that no light is...
Page 447 7-3. Do-it-yourself maintenance Front side marker lights ■ Turn the bulb base counter- clockwise. Remove the light bulb. When installing, reverse the steps listed. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 448 7-3. Do-it-yourself maintenance Front turn signal/parking lights ■ Turn the bulb base counter- clockwise. Remove the light bulb. When installing, reverse the steps listed. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 449 7-3. Do-it-yourself maintenance Stop/tail/rear side marker lights and rear turn signal lights ■ Open trunk remove the clips. To prevent damage to the vehi- cle, cover the tip of the screw- driver with a rag. Partly remove the luggage trim cover. Turn the bulb base counter- clockwise.
Page 450 7-3. Do-it-yourself maintenance Back-up lights ■ Open trunk remove the cover. Turn the bulb base counter- clockwise. Remove the light bulb. When installing, reverse the steps listed. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 451 7-3. Do-it-yourself maintenance License plate lights ■ Open trunk remove the trunk panel cover clips. To prevent damage to the vehi- cle, cover the tip of the screw- driver with a rag. Partly remove the trunk panel cover and turn the bulb base counterclockwise.
Page 452 Temporary condensation build-up on the inside of the headlight lens does not indicate a malfunction. Contact your Toyota dealer for more information in the following situations: Large drops of water have built up on the inside of the lens. ●...
Page 453 7-3. Do-it-yourself maintenance COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 454 8-1. Essential information Emergency flashers The emergency flashers are used to warn other drivers when the vehicle has to be stopped in the road due to a breakdown, etc. Press the switch. All the turn signal lights will flash. To turn them off, press the switch once again.
Page 455 8-1. Essential information If your vehicle has to be stopped in an emergency Only in an emergency, such as if it becomes impossible to stop the vehicle in the normal way, stop the vehicle using the follow- ing procedure: Steadily step on the brake pedal with both feet and firmly depress it. Do not pump the brake pedal repeatedly as this will increase the effort required to slow the vehicle.
Page 456 8-1. Essential information CAUTION If the engine has to be turned off while driving ■ Power assist for the brakes and steering wheel will be lost, making the ● brake pedal harder to depress and the steering wheel heavier to turn. Decelerate as much as possible before turning off the engine.
Page 457 If your vehicle needs to be towed If towing is necessary, we recommend having your vehicle towed by your Toyota dealer or commercial towing service, using a lift-type truck or flatbed truck. Use a safety chain system for all towing, and abide by all state/ provincial and local laws.
Page 458 Release the parking brake. Use a towing dolly under the front wheels. Using a flatbed truck If your Toyota is transported by a flatbed truck, it should be tied down at the locations shown in the illustration. If you use chains or cables to tie down your vehicle, the angles shaded in black must be 45 .
Page 459 8-2. Steps to take in an emergency Emergency towing If a tow truck is not available in an emergency, your vehicle may be temporarily towed using a cable or chain secured to the emergency towing eyelet. This should only be attempted on hard surfaced roads for 50 miles (80 km) at low speeds.
Page 460 8-2. Steps to take in an emergency CAUTION Observe the following precautions. Failure to do so may result in death or serious injury. When towing the vehicle ■ Be sure to transport the vehicle with the front wheels raised or with all four wheels raised off the ground.
Page 461 8-2. Steps to take in an emergency If you think something is wrong If you notice any of the following symptoms, your vehicle proba- bly needs adjustment or repair. Contact your Toyota dealer as soon as possible. Visible symptoms ● Fluid leaks under the vehicle.
Page 462 8-2. Steps to take in an emergency Fuel pump shut off system To minimize the risk of fuel leakage when the engine stalls or when an airbag inflates upon collision, the fuel pump shut off system stops the supply of fuel to the engine. Follow the procedure below to restart the engine after the system is activated.
Page 463 Immediately stop the vehicle in a safe place and con- (Canada) tact your Toyota dealer. Continuing to drive the vehi- cle may be dangerous. Charging system warning light Indicates a malfunction in the vehicle’s charging system Immediately stop the vehicle in a safe place and con- tact your Toyota dealer.
Page 464 • The electronic throttle control system; (U.S.A.) • The electronic automatic transmission control system; or • The electronic continuously variable transmission con- trol system. Have the vehicle inspected by your Toyota dealer (Canada) immediately. SRS warning light Indicates a malfunction in: •...
Page 465 Warning light Warning light/Details/Actions 3, 6 Cruise control indicator light Indicates a malfunction in the cruise control system. Have the vehicle inspected by your Toyota dealer immediately. (Comes on in yellow) 2, 3 Open door warning light (warning buzzer) Indicates that a door or the trunk is not fully closed Check that all the doors and the trunk are closed.
Page 466 8-2. Steps to take in an emergency Warning light Warning light/Details/Actions Maintenance required reminder light Indicates that maintenance is required according to the driven distance on the maintenance schedule. Illuminates for about 3 seconds and then flashes for about 15 seconds approximately 4500 miles (7200 km) after the maintenance data has been reset.
Page 467 8-2. Steps to take in an emergency : Driver’s seat belt buzzer: Vehicles without a smart key system: The driver’s seat belt buzzer sounds to alert the driver that his or her seat belt is not fastened. Once the engine switch is turned to the “ON”...
Page 468 8-2. Steps to take in an emergency Follow the correction procedures. (vehicles with a smart key system and with a drive monitor display) After taking the specified steps to correct the suspected problem, check that the warning light turns off. Interior Exterior Warning...
Page 469 8-2. Steps to take in an emergency Interior Exterior Warning Warning light/Details/Action buzzer buzzer light Smart key system indicator light An attempt was made to exit the vehicle with Continuous the electronic key and lock the doors without Once (5 seconds) first turning the engine switch off.
Page 470 If it is, tighten it securely. The light will go off after several driving trips. If the light does not go off even after several trips, contact your Toyota dealer as soon as possible. When the tire pressure warning light comes on (vehicles with a tire ■...
Page 471 If there is a lot of snow or ice on the vehicle, in particular around the ● wheels or wheel housings If non-genuine Toyota wheels are used (Even if you use Toyota wheels, ● the tire pressure warning system may not work properly with some types of tires.)
Page 472 If both the ABS and the brake system warning lights remain on ■ Stop your vehicle in a safe place immediately and contact your Toyota dealer. The vehicle will become extremely unstable during braking, and the ABS system may fail, which could cause an accident resulting in death or serious injury.
Page 473 8-2. Steps to take in an emergency CAUTION Maintenance of the tires ■ Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label (tire and load information label).
Page 474 8-2. Steps to take in an emergency NOTICE To ensure the tire pressure warning system operates properly ■ (vehicles with a tire pressure warning system) Do not install tires with different specifications or makers, as the tire pressure warning system may not operate properly. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 475 Multi-information display If any of the warning message or indicator comes on again after the following actions have been performed, contact your Toyota dealer. Warning message and warning buzzer list Warning message Details/Actions Indicates that one or more of the doors is not fully closed.
Page 476 Indicates a malfunction in the smart key system (if equipped). A buzzer also sounds. Have the vehicle inspected by your Toyota dealer. (Flashes) Indicates a malfunction in the cruise control sys- tem (if equipped).
Page 477 8-2. Steps to take in an emergency Warning message Details/Actions Indicates that the moon roof is not fully closed (with the engine switch off, and the driver’s door open) A buzzer also sounds. Close the moon roof. (Flashes) (If equipped) Indicates that the washer fluid level is low.
Page 478: Smart Key System
8-2. Steps to take in an emergency Have the malfunction repaired immediately. (vehicles with a smart key system) After taking the specified steps to correct the suspected problem, check that the warning message and light go off. Interior Exterior Warning message Details/Actions buzzer buzzer...
Page 479 8-2. Steps to take in an emergency Interior Exterior Warning message Details/Actions buzzer buzzer The electronic key was carried outside the vehicle and a door other than the driver’s door was opened and closed while the engine switch was in a mode other than off.
Page 480 8-2. Steps to take in an emergency Interior Exterior Warning message Details/Actions buzzer buzzer An attempt was made to drive when the regular key was not inside the vehicle. times Confirm that elec- tronic key is inside the vehicle. (Flashes) An attempt was made to lock the doors using the smart key Contin-...
Page 481 8-2. Steps to take in an emergency Interior Exterior Warning message Details/Actions buzzer buzzer The steering lock could not be released within 3 seconds of engine switch being pressed. Once Press the engine switch while depressing the brake pedal moving (Flashes) steering wheel left and right.
Page 482 8-2. Steps to take in an emergency Interior Exterior Warning message Details/Actions buzzer buzzer • When doors were unlocked with the mechanical key and then the engine switch was pressed, the elec- tronic could detected in the vehicle. • The electronic key could not be detected in the vehicle even after the engine switch was pressed two consecu-...
Page 483 8-2. Steps to take in an emergency Interior Exterior Warning message Details/Actions buzzer buzzer The driver’s door was opened and closed with the engine switch turned off and then the engine switch ACCESSORY or IGNITION ON mode twice without the engine being started.
Page 484 8-2. Steps to take in an emergency Interior Exterior Warning message Details/Actions buzzer buzzer An attempt was made to start the engine with the shift lever in Once an incorrect position. Shift the shift lever to P and start the engine. (Flashes) (Vehicles with a continuously variable transmission)
Page 485 8-2. Steps to take in an emergency If you have a flat tire Your vehicle is equipped with a spare tire. The flat tire can be replaced with the spare tire. For details about tires: P. 448 CAUTION If you have a flat tire ■...
Page 486 8-2. Steps to take in an emergency Location of the spare tire, jack and tools Luggage floor cover Jack Wheel nut wrench Spare tire Jack handle Tool tray Jack attachment : The jack attachment is used when raising your vehicle with a floor jack. ( P.
Page 487 8-2. Steps to take in an emergency CAUTION Using the tire jack ■ Observe the following precautions. Improper use of the tire jack may cause the vehicle to suddenly fall off the jack, leading to death or serious injury. Do not use the tire jack for any purpose other than replacing tires or ●...
Page 488 8-2. Steps to take in an emergency Take out the jack. For tightening For loosening Taking out the spare tire Remove the luggage floor cover. ( P. 515) Remove the tool tray. Loosen the center fastener that secures the spare tire. CAUTION When storing the spare tire ■...
Page 489 8-2. Steps to take in an emergency Replacing a flat tire Chock the tires. Flat tire Wheel chock positions Left-hand side Behind the rear right-hand side tire Front Right-hand side Behind the rear left-hand side tire Left-hand side In front of the front right-hand side tire Rear Right-hand side In front of the front left-hand side tire...
Page 490 8-2. Steps to take in an emergency Turn the tire jack portion “A” by hand until the notch of the jack is in contact with the jack point. The jack point guides are located under the rocker panel. They indicate the jack point positions. Raise the vehicle until the tire is slightly raised off the ground.
Page 491 • If there are any cracks or deformations in the bolt screws, nut threads or bolt holes of the wheel, have the vehicle inspected by your Toyota dealer. • When installing the wheel nuts, be sure to install them with the tapered ends facing inward.
Page 492 8-2. Steps to take in an emergency Installing the spare tire Remove any dirt or foreign mat- ter from the wheel contact sur- face. If foreign matter is on the wheel contact surface, the wheel nuts may loosen while the vehicle is in motion, causing the tire to come off.
Page 493 8-2. Steps to take in an emergency Firmly tighten each wheel nut two or three times in the order shown in the illustration. Tightening torque: 76 ft•lbf (103 N•m, 10.5 kgf•m) Stow the flat tire, tire jack and all tools. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 494 8-2. Steps to take in an emergency The compact spare tire ■ The compact spare tire is identified by the label “TEMPORARY USE ● ONLY” on the tire sidewall. Use the compact spare tire temporarily, and only in an emergency. Make sure to check the tire inflation pressure of the compact spare tire.
Page 495 8-2. Steps to take in an emergency CAUTION When using the compact spare tire ■ Remember that the compact spare tire provided is specifically ● designed for use with your vehicle. Do not use your compact spare tire on another vehicle. Do not use more than one compact spare tires simultaneously.
Page 496 When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and transmitter when replacing the tire.
Page 497 8-2. Steps to take in an emergency If the engine will not start If the engine will not start even though correct starting proce- dures are being followed ( P. 161, 164), consider each of the fol- lowing points: The engine will not start even though the starter motor operates normally.
Page 498 ● There may be a malfunction in the steering lock system (vehicles with a smart key system). Contact your Toyota dealer if the problem cannot be repaired, or if repair procedures are unknown. Emergency start function (vehicles with a smart key system)
Page 499 (a sys- tem to prevent accidental operation of the shift lever). Have the vehicle inspected by your Toyota dealer immediately. The following steps may be used as an emergency measure to ensure that the shift lever can be shifted: Set the parking brake.
Page 500 8-2. Steps to take in an emergency If the electronic key does not operate properly (vehicles with a smart key system) If communication between the electronic key and vehicle is interrupted ( P. 115) or the electronic key cannot be used because the battery is depleted, the smart key system and wire- less remote control cannot be used.
Page 501 Vehicles with a multi-information display: Firmly depress the brake pedal (continuously variable transmission) or clutch pedal (manual transmission) and check that is shown on the multi-informa- tion display. Press the engine switch. In the event that the engine still cannot be started, contact your Toyota dealer. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 502 8-2. Steps to take in an emergency Stopping the engine ■ Shift the shift lever to P (continuously variable transmission) or N (manual transmission) and press the engine switch as you normally do when stopping the engine. Replacing the key battery ■...
Page 503 The following procedures may be used to start the engine if the vehicle’s battery is discharged. You can also call your Toyota dealer or a qualified repair shop. If you have a set of jumper (or booster) cables and a second vehicle with a 12-volt battery, you can jump start your vehicle by following the steps below.
Page 504 8-2. Steps to take in an emergency Connect the jumper cables according to the following procedure: Connect a positive jumper cable clamp to the positive (+) battery terminal on your vehicle. Connect the clamp on the other end of the positive cable to the positive (+) battery terminal on the second vehicle.
Page 505 IGNITION ON mode, then start the vehicle's engine. Once the vehicle’s engine has started, remove the jumper cables in the exact reverse order from which they were connected. Once the engine starts, have the vehicle inspected at your Toyota dealer as soon as possible. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 506 8-2. Steps to take in an emergency Starting the engine when the battery is discharged ■ The engine cannot be started by push-starting. To prevent battery discharge ■ Turn off the headlights and the audio system while the engine is off. ●...
Page 507 8-2. Steps to take in an emergency CAUTION Avoiding battery fires or explosions ■ Observe the following precautions to prevent accidentally igniting the flam- mable gas that may be emitted from the battery: Make sure each jumper cable is connected to the correct terminal and that ●...
Page 508 If you do not see steam: Carefully lift the hood. After the engine has cooled down sufficiently, inspect the hoses and radiator core (radia- tor) for any leaks. Radiator Cooling fan If a large amount of coolant leaks, immediately contact your Toyota dealer. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 509 8-2. Steps to take in an emergency The coolant level is satisfactory if it is between the “F” and “L” lines on the reservoir. Reservoir “F” line “L” line Radiator cap Add engine coolant if neces- sary. Water can be used in an emer- gency if engine coolant is unavail- able.
Page 510 8-2. Steps to take in an emergency If the fan is not operating: Stop the engine immediately and contact your Toyota dealer. If the fan is operating: Have the vehicle inspected at the nearest Toyota dealer. CAUTION When inspecting under the hood of your vehicle ■...
Page 511 8-2. Steps to take in an emergency NOTICE When adding engine coolant ■ Add coolant slowly after the engine has cooled down sufficiently. Adding cool coolant to a hot engine too quickly can cause damage to the engine. To prevent damage to the cooling system ■...
Page 512 8-2. Steps to take in an emergency If the vehicle becomes stuck Carry out the following procedures if the tires spin or the vehicle becomes stuck in mud, dirt or snow: Stop the engine. Set the parking brake and shift the shift lever to P (automatic transmission or continuously variable transmission) or N (manual transmission).
Page 513 8-2. Steps to take in an emergency When it is difficult to free the vehicle (vehicles with a TRAC system) ■ Press to turn off TRAC. CAUTION When attempting to free a stuck vehicle ■ If you choose to push the vehicle back and forth to free it, make sure the surrounding area is clear to avoid striking other vehicles, objects or people.
Page 514 8-2. Steps to take in an emergency COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 515 The vehicle identification number (VIN) is the legal identifier for your vehicle. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle. This number is stamped on the top left of the instrument panel.
Page 516 9-1. Specifications This number is also on the Certifi- cation Label on the driver’s side center pillar. Engine number ■ The engine number is stamped on the engine block as shown. COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 517: Lubrication System
9-1. Specifications Engine Model 1.8 L 4-cylinder (2ZR-FE and 2ZR-FAE) engines Type 4 cylinder in line, 4 cycle, gasoline Bore and stroke 3.17 3.48 in. (80.5 88.3 mm) Displacement 109.7 cu. in. (1798 cm 2ZR-FE 143 ± 22 lbf (650 ± 100 N, 65 ± 10 kgf) Drive belt tension 2ZR-FAE Automatic adjustment...
Page 518 9-1. Specifications Engine oil selection ■ “Toyota Genuine Motor Oil” is used in your Toyota vehicle. Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to sat- isfy the following grade and viscosity. Oil grade: ILSAC GF-5 multigrade engine oil...
Page 519: Ignition System
Cooling system Capacity (Reference) 5.8 qt. (5.5 L, 4.8 Imp. qt.) Use either of the following. • “Toyota Super Long Life Coolant” • Similar high-quality ethylene glycol-based Coolant type non-silicate, non-amine, non-nitrite, and non- borate coolant with long-life hybrid organic...
Page 520 Please be aware that depending on the particular characteristics of the gear oil used or the operating conditions, idle sound, shift feeling and/or fuel effi- ciency may be different or affected. Toyota recommends to use “TOYOTA Genuine Manual Transmission Gear Oil LV” to achieve optimal perfor- mance.
Page 521 Toyota Genuine ATF WS NOTICE Automatic transmission fluid type ■ Using automatic transmission fluid other than “Toyota Genuine ATF WS” may cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ultimately damage the transmission of your vehicle.
Page 522 9-1. Specifications Brakes 1.8 L 4-cylinder (2ZR-FE) engine 2.9 in. (74 mm) Pedal clearance 1.8 L 4-cylinder (2ZR-FAE) engine 2.8 in. (71 mm) Pedal free play 0.04 0.24 in. (1 6 mm) Brake pad wear limit 0.04 in. (1.0 mm) Parking brake lining wear limit 0.04 in.
Page 523 9-1. Specifications Steering Free play Less than 1.2 in. (30 mm) Tires and wheels Type A 195/65R15 91S, T135/80R16 101M, Tire size T135/80D16 101M Tire inflation pressure Front: 35 psi (240 kPa, 2.4 kgf/cm or bar) (Recommended cold tire Rear: 35 psi (240 kPa, 2.4 kgf/cm or bar) inflation pressure) Spare: 60 psi (420 kPa, 4.2 kgf/cm...
Page 524 9-1. Specifications Light bulbs Light bulbs Bulb No. Type Headlights High beam 9005 Front side marker lights Front turn signal/park- 7444NA 28/8 ing lights Front fog lights Exterior Side turn signal lights Rear turn signal lights Stop/tail and rear side 7443 21/5 marker lights...
Page 525 In very few cases, driveability problems may be caused by the brand of gaso- line you are using. If driveability problems persist, try changing the brand of gasoline. If this does not correct the problem, consult your Toyota dealer. Gasoline quality standards ■...
Page 526 MTBE (Methyl Tertiary Butyl Ether) is available in many areas. Toyota recommends the use of cleaner burning gasoline and appropriately blended reformulated gasoline. These types of gasoline provide excellent vehicle performance, reduce vehicle emissions and improve air quality.
Page 527 ■ Some gasoline contains an octane enhancing additive called MMT (Methylcy- clopentadienyl Manganese Tricarbonyl). Toyota does not recommend the use of gasoline that contains MMT. If fuel containing MMT is used, your emission control system may be adversely affected. The malfunction indicator lamp on the instrument cluster may come on. If this happens, contact your Toyota dealer for service.
Page 528 9-1. Specifications Tire information Typical tire symbols Full-size tire Compact spare tire COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 529 9-1. Specifications Tire size ( P. 560) DOT and Tire Identification Number (TIN)( P. 559) Uniform tire quality grading For details, see “Uniform Tire Quality Grading” that follows. Location of treadwear indicators( P. 448) Tire ply composition and materials Plies are layers of rubber-coated parallel cords. Cords are the strands which form the plies in a tire.
Page 530 9-1. Specifications Typical DOT and Tire Identification Number (TIN) DOT symbol Tire Identification Number (TIN) Tire manufacturer’s identifica- tion mark Tire size code Manufacturer’s optional tire type code (3 or 4 letters) Manufacturing week Manufacturing year : The DOT symbol certifies that the tire conforms to applicable Federal Motor Vehicle Safety Standards.
Page 531 9-1. Specifications Tire size Typical tire size information ■ The illustration indicates typical tire size. Tire use (P = Passenger car, T = Temporary use) Section width (millimeters) Aspect ratio (tire height to section width) Tire construction code (R = Radial, D = Diagonal) Wheel diameter (inches) Load index (2 digits or 3 digits)
Page 532 9-1. Specifications Tire section names Bead Sidewall Shoulder Tread Belt Inner liner Reinforcing rubber Carcass Rim lines Bead wires Chafer COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 533 U.S. Department of Transportation. It provides the purchasers and/or prospective purchasers of Toyota vehicles with information on uniform tire quality grading. Your Toyota dealer will help answer any questions you may have as you read this information. DOT quality grades ■...
Page 534 9-1. Specifications Temperature A, B, C ■ The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissi- pate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 535 9-1. Specifications Glossary of tire terminology Tire related term Meaning Tire pressure when the vehicle has been Cold tire inflation pres- parked for three hours or more, or has not sure been driven more than 1 mile or 1.5 km under that condition The maximum cold inflated pressure to which Maximum...
Page 536 9-1. Specifications Tire related term Meaning The combined weight of installed regular pro- duction options weighing over 5 lb. (2.3 kg) in excess of the standard items which they Production options replace, not previously considered in curb weight weight or accessory weight, including heavy duty brakes, ride levelers, roof rack, heavy duty battery, and special trim A metal support for a tire or a tire and tube...
Page 537 9-1. Specifications Tire related term Meaning A pneumatic tire in which the ply cords that extend to the beads are laid at alternate Bias ply tire angles substantially less than 90 degrees to the centerline of the tread The tire structure, except tread and sidewall Carcass rubber which, when inflated, bears the load The breaking away of pieces of the tread or...
Page 538 9-1. Specifications Tire related term Meaning A tire designated by its manufacturer as pri- Light truck (LT) tire marily intended for use on lightweight trucks or multipurpose passenger vehicles The maximum load that a tire is rated to carry Load rating for a given inflation pressure The load rating for a tire at the maximum per- Maximum load rating...
Page 539 9-1. Specifications Tire related term Meaning The linear distance between the exteriors of the sidewalls of an inflated tire, excluding ele- Section width vations due to labeling, decoration, or protec- tive bands That portion of a tire between the tread and Sidewall bead The parting of the rubber compound from the...
Page 540 9-1. Specifications Designated seating Occupant distribution Vehicle normal load, capacity, Number of in a normally loaded Number of occupants occupants vehicle 2 through 4 2 in front 2 in front, 1 in second 5 through 10 seat 2 in front, 1 in second 11 through 15 seat, 1 in third seat, 1 in fourth seat...
Page 541 Your vehicle includes a variety of electronic features that can be personalized to suit your preferences. Programming these pref- erences requires specialized equipment and may be performed by your Toyota dealer. Customizing vehicle features Changing by using the navigation system ■...
Page 542 9-2. Customization Customizable features Some function settings are changed simultaneously with other func- tions being customized. Contact your Toyota dealer for further details. Settings that can be changed using the navigation system/multime- dia system Settings that can be changed by your Toyota dealer Definition of symbols: O = Available, —=Not available...
Page 543 9-2. Customization Smart key system and wireless remote control ( P. 97, 106) ■ Customized set- Function Default setting ting Operation buzzer volume 1 to 7 Operation signal (emer- gency flashers) Time elapsed before auto- matic door lock function is 30 seconds activated if door is not 60 seconds...
Page 544 9-2. Customization Smart key system ( P. 97, 106, 111) ■ Customized set- Function Default setting ting Smart key system — O Number permissible times of continuous smart Twice Unlimited — O lock : If equipped Wireless remote control ( P. 92, 97, 106) ■...
Page 545 9-2. Customization Turn signal lever ( P. 182) ■ Customized set- Function Default setting ting The number of times the turn signal lights flash automatically when — O turn signal lever is moved to the first position during a lane change : After flashing the turn signal lights when turning left or right while this func- tion is off and the turn signal lever is moved to the first position in the direc- tion of the flashing light, the turn signal lights can be selected to be flashing...
Page 546 9-2. Customization Lights ( P. 184) ■ Customized set- Function Default setting ting Daytime running light sys- : U.S.A. only Automatic air conditioning system ( P. 386) ■ Customized set- Function Default setting ting conditioning auto switch operation : If equipped Illumination ( P.
Page 547 9-2. Customization Vehicle customization ■ When the doors remain closed after unlocking the doors and the timer acti- vated automatic door lock function activates, signals will be generated in accordance with the operational signal (Emergency flashers) function set- tings. When customizing using the navigation system ■...
Page 548 9-3. Items to initialize Items to initialize The following items must be initialized for normal system opera- tion after such cases as maintenance being performed on the vehicle: Item When to initialize Reference Maintenance data (U.S.A. • After the maintenance is per- P.
Page 549 9-3. Items to initialize COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 550 ● If you lose your keys or mechanical keys, new genuine keys or mechanical keys can be made by your Toyota dealer. ( P. 94) ● If you lose your keys or electronic keys, the risk of vehicle theft increases significantly.
Page 551 What to do if... (Troubleshooting) The rear door cannot be opened ● Is the child-protector lock set? The rear door cannot be opened from inside the vehicle when the lock is set. Open the rear door from outside and then unlock the child-protector lock.
Page 552 What to do if... (Troubleshooting) If you think something is wrong The engine does not start (vehicles without a smart key system) ● Vehicles with a manual transmission: Do you turn the key with the clutch pedal depressed firmly? ( P. 161) ●...
Page 553 What to do if... (Troubleshooting) The shift lever cannot be shifted from P even if you depress the brake pedal (vehicles with an automatic transmission or continuously variable transmission) ● Vehicles without a smart key system: Is the engine switch in the “ON” position? If you cannot release the shift lever by depressing the brake pedal with the engine switch in the “ON”...
Page 554 What to do if... (Troubleshooting) The engine switch is turned off automatically (vehicles with a smart key system) ● The auto power off function will be operated if the vehicle is left in ACCES- SORY or IGNITION ON mode (the engine is not running) for a period of time.
Page 555 What to do if... (Troubleshooting) A warning light turns on or a warning message or indica- tor is displayed (vehicles with a multi-information display) ● When a warning light turns on or a warning message or indicator is dis- played, refer to P. 491, 503. When a problem has occurred If you have a flat tire ●...
Page 556 National Highway Traffic Safety Administration (NHTSA) in addi- tion to notifying Toyota Motor Sales, U.S.A., Inc. (Toll-free: 1-800- 331-4331). If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Page 557 Seat belt instructions for Canadian owners (in French) The following is a French explanation of seat belt instructions extracted from the seat belt section in this manual. See the seat belt section for more detailed seat belt instructions in English. Utilisation correcte des ceintures de sécurité...
Page 558 ATTENTION Dommage et usure de la ceinture de sécurité ■ Inspectez la ceinture de sécurité périodiquement. Vérifiez si elles ne sont pas entaillées, effilochées et que leurs ancrages ne sont pas desserrés. N’utilisez pas une ceinture de sécurité défectueuse avant qu’elle ne soit remplacée.
Page 559 SRS airbag instructions for Canadian owners (in French) The following is a French explanation of SRS airbag instructions extracted from the SRS airbag section in this manual. See the SRS airbag section for more detailed SRS airbag instruc- tions in English. ◆...
Page 560 ◆ Coussins gonflables latéraux et rideaux SRS Coussins gonflables latéraux avant SRS Participent à la protection du thorax des occupants du siège avant Coussins gonflables rideaux SRS Participent principalement à la protection de la tête des occupants assis aux places extérieures Compositions du système de coussin gonflable SRS COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 561 Capteurs d’impact avant Coussins gonflables rideaux Système de classification de Capteurs d’impact latéral l’occupant du passager avant (arrière) (ECU et capteurs) Coussin gonflable conducteur Coussin gonflable d’assise Bouton de la boucle de cein- Capteurs d’impact latéral ture de sécurité du conducteur (porte avant) Coussin gonflable de genoux Coussin gonflable passager...
Page 562 ATTENTION Précautions concernant le coussin gonflable SRS ■ Respectez les précautions suivantes concernant les coussins gonflables SRS. Autrement, des blessures graves, voire mortelles, pourraient s’ensuivre. Le conducteur et les passagers du véhicule doivent porter correctement ● leur ceinture de sécurité. Les coussins gonflables SRS sont des dispositifs supplémentaires à...
Page 563 être grièvement blessés ou tués par le déploiement du coussin gonflable. Installez dans un siège de sécurité enfant les enfants trop jeunes pour pouvoir utiliser la ceinture de sécurité. Toyota recom- mande vivement que les nourrissons et les enfants soient installés sur le siège arrière du véhicule et convenablement attachés.
Page 564 ATTENTION Précautions concernant le coussin gonflable SRS ■ Ne vous asseyez pas sur le bord du ● siège et ne vous appuyez pas contre le tableau de bord. Ne laissez pas un enfant se tenir ● debout devant le coussin gonflable pas- sager avant SRS ou bien s’asseoir sur les genoux du passager avant.
Page 565 ATTENTION Précautions concernant le coussin gonflable SRS ■ Ne fixez ni ne posez aucun objet sur ● des emplacements tels que le tableau de bord, la garniture du volant de direc- tion et la partie inférieure du tableau de bord. Ces objets risquent de se transformer en projectile lorsque les coussins gon- flables du conducteur, passager avant...
Page 566 ● ture du moyeu de volant et les garnitures de montants avant et arrière, apparaissent abîmées ou craquelées, faites-les remplacer par votre con- cessionnaire Toyota. Ne placez rien sur le siège du passager avant, comme un coussin par ● exemple. Cela a pour conséquence de répartir le poids du passager, ce qui empêche le capteur de détecter correctement le poids du passager.
Page 567 SRS Ne mettez pas votre véhicule au rebut et n’effectuez pas les modifications suivantes sans consulter votre concessionnaire Toyota. Les coussins gon- flables SRS peuvent être défaillants ou se déployer (se gonfler) accidentel- lement, provoquant la mort ou de graves blessures.
Page 568 COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 569: Gas Station Information
13.2 gal. (50 L, 10.9 Imp. gal.) (Reference) Fuel type P. 194, 546 Cold tire inflation P. 552 pressure Engine oil capacity (Drain and refill — P. 546 reference) “Toyota Genuine Motor Oil” or equivalent Engine oil type P. 546 COROLLA_TMMMS_TMMC_U (OM12F00U)
Page 570 Alphabetical index Alphabetical index Antennas (smart key system) ....111 A/C ........380, 386 Anti-lock Brake System Air conditioning filter ..... 461 (ABS) ........211 Function........ 211 (Anti-lock Brake System)..211 Warning light......492 Function ........ 211 Assist grips......406 Warning light......
Page 571 Alphabetical index Back-up lights Care ........414, 417 Aluminum wheels ....415 Replacing light bulb ....477 Wattage ........ 553 Exterior ......... 414 Battery ........444 Interior ........417 Battery checking ....444 Seat belts......418 If the vehicle has discharged Cargo capacity......
Page 572 Alphabetical index Child safety ........ 52 Airbag precautions....36 Daytime running light Battery precautions..445, 535 system........188 Child restraint system ..... 53 Defogger How your child should wear Outside rear view the seat belt......30 mirrors ......381, 389 Installing child restraints ..
Page 573 Alphabetical index Emergency flashers ....482 Engine ........546 Eco drive mode......175 ACCESSORY mode ..... 166 Eco Driving Indicator ....89 Compartment......435 Electric Power Steering Engine switch ....161, 164 (EPS)........211 Hood ........431 Function ........ 211 How to start the Warning light......
Page 574 Alphabetical index Fuel ........... 194 Capacity........ 546 Flat tire Fuel gauge......77, 82 Vehicles with a spare tire..513 Fuel pump shut off system ... 490 Floor mats ........24 Information......554 Fluid Refueling ......194 Automatic transmission..550 Type......194, 546 Brake ........
Page 575 Alphabetical index Hands-free system Jack Positioning the jack....433 (for cellular phone)..255, 320 Head restraints ......124 Vehicle-equipped jack ..514 Headlights ........ 184 Jack handle......514 Light switch ......184 Jam protection function Replacing light bulbs..470, 479 Moon roof ......
Page 576 Alphabetical index LATCH anchors ......58 Maintenance Do-it-yourself maintenance... 428 Lever Auxiliary catch lever....431 General maintenance ... 423 Hood lock Maintenance data ....544 release lever....... 431 Maintenance Shift lever..172, 174, 176, 180 requirements ...... 420 Turn signal lever ....182 Reset the maintenance Wiper lever......
Page 577 Alphabetical index Multimedia system ....283 Audio input......286 Paddle shift switches..177, 178 AUX port/USB Parking brake......183 port ........286 Operation......183 ® Bluetooth audio....336 Parking brake engaged CD player......302 warning buzzer....503 iPod........308 Parking brake engaged MP3/WMA disc .....
Page 578 Alphabetical index Radiator ........442 Seat belt reminder light ..493 Seat belts ........28 Radio......... 230, 300 Rear interior light..... 397 Adjusting the seat belt .... 29 Rear seat Automatic Locking Folding down ......122 Retractor (ALR) ....30 Rear turn signal lights.....
Page 579 Alphabetical index Shift lever ..172, 174, 176, 180 Storage feature ......398 Automatic transmission..172 Stuck Continuously variable If the vehicle becomes transmission ....174, 176 stuck........540 If the shift lever cannot Sun visors ........ 403 be shifted from P ....527 Sun shade Manual transmission.....
Page 580 Alphabetical index Warning light......493 Tools......... 514 Tachometer ......77, 82 Top tether strap ......62 Tail lights........184 Total load capacity ....156 Light switch ......184 Towing Replacing light bulbs..... 476 Dinghy towing ....158, 159 Wattage ........ 553 Emergency towing ....
Page 581 Alphabetical index Open door......493 Seat belt reminder light..493 Vanity mirrors ......403 Slip indicator ......492 Vehicle data recording ....9 Smart key system ....492 Vehicle identification SRS ........492 number ........544 Tire pressure ......493 Vehicle Stability Control Warning messages....
Page 582 2015 Entune Premium Audio ™ with Navigation and App Suite...
Page 583: Table Of Contents
Navigation Owner’s Manual. We strongly encourage you to review the Navigation Phone Compatibility Owner’s Manual, the quick reference guide and visit www.toyota.com/entune so you will have a ENTUNE - HOW TO GET STARTED better understanding of all your vehicles features and controls.
Page 584: What Is Entune
Apps identified by "™" or "®" are trademarks or registered trademarks of their respective companies and cannot be used without permission. See toyota.com/entune for the latest information regarding apps and services.
Page 585: Basic Overview
Click on the link embedded in the email to activate your account. www.myentune.com and Terms of Service Privacy Policy © 2011 Toyota Motor Sales, U.S.A., Inc. All information applies to U.S. vehicles only. CONNECT PHONE create a personal Entune See page 7 for instructions. App account using your computer.
Page 586: Connect A Bluetooth Phone
Before you begin using the voice recognition system, it is recommended that you access "Train Voice Pairing your phone is the first step in connecting with your Toyota for hands-free calling and for audio streaming via Bluetooth. The pairing process is quick and easy: all iPhone mobile digital devices and Recognition"...
Page 587: Calling By Voice Recognition
CALLING BY VOICE RECOGNITION CALLING BY VOICE RECOGNITION DIAL BY NUMBER DIAL BY NAME If you are able to successfully transfer your phone book, you can dial by name using voice recognition. Please say the name exactly as it is entered in your phone when in the telephone screen. If you have difficulty pairing your phone, or are unable to transfer your cell phone book, please refer to the cell phone manufacturer's user guide.
Page 588: Destination Input
DESTINATION INPUT DESTINATION INPUT BY ADDRESS BY ADDRESS From the home screen, touch the map. step step Input the house number and touch step Touch the desired street name. step Press and enter the desired State/ followed by Province. Input the city name. step step step...
Page 589: Note On Voice Recognition
DESTINATION INPUT DESTINATION INPUT - POINT OF INTEREST (POI) NOTE ON VOICE RECOGNITION POINT OF INTEREST BY NAME The navigation system's voice recognition feature will compare your spoken words with computer-generated word patterns preprogrammed in the database. If the system does not provide your intended match, please try a different pronunciation.
Page 590: Point Of Interest By Category - Voice Recognition
DESTINATION INPUT - POINT OF INTEREST (POI) DESTINATION INPUT - POINT OF INTEREST (POI) POINT OF INTEREST BY CATEGORY POINT OF INTEREST BY CATEGORY - VOICE RECOGNITION Quick Tip -You can search for many dining, hotel and fuel chains by name, e.g., "Find Nearby Starbucks." From the home screen, touch the map.
Page 591: Set Home
SET HOME SET HOME Press the Set Up icon on the Touch the desired city name. Input the street name and touch step step step step Touch faceplate followed by Quick Tip - Enter the street name without prefixes such as North or the letter N. The system will display the base street name without prefixes or suffixes on the next screen.
Page 592: Additional Features
ADDITIONAL NAVIGATION FEATURES ADDITIONAL NAVIGATION FEATURES OPERATION OF EMERGENCY SCREEN BEEP SETTING VOICE VOLUME SEARCH AREA Prior to inputting the desired address select the State/ PRESS SET UP ICON > PRESS SET UP ICON > PRESS > Province by pressing .
Page 593: Traffic
TRAFFIC TRAFFIC MY TRAFFIC ROUTES The Traffic App integrates with your navigation system to display continuously updated traffic information for over 100 markets. Just begin by pressing the APPS button and selecting My Traffic Routes lets you store favorite and previously traveled routes to check traffic conditions. To see traffic routes, touch TRAFFIC EVENT LIST AUTOMATICALLY AVOID TRAFFIC...
Page 594: Weather
WEATHER ENTUNE APP SUITE FEATURES The weather app allows you to access Doppler weather radar information. You can also check the weather Once your phone is connected via Bluetooth, Entune lets you access many useful apps. These are some of the top forecast for other cities.
Page 595 NOTES NOTES...
Page 596 00505-NAV14-ENPRE Printed in the USA 08/13...

This manual is also suitable for:

2014 corolla

Toyota 2015 Corolla Owner's Manual

Screen Configurations

Traffic Event List

Predictive Traffic Map

Automatically Avoid Traffic

Quick Links

Summary of Contents for Toyota 2015 Corolla

Page 8: Adjusting The Mirrors

Page 160: Operating Instructions

Page 263: Random Playback

Page 374: Bottle Holders

Page 379: Power Outlet

Page 380: Assist Grips

Page 413: Engine Coolant

Page 478: Smart Key System

Page 517: Lubrication System

Page 519: Ignition System

Page 569: Gas Station Information

Page 583: Table Of Contents

Page 584: What Is Entune

Page 585: Basic Overview

Page 586: Connect A Bluetooth Phone

Page 587: Calling By Voice Recognition

Page 588: Destination Input

Page 589: Note On Voice Recognition

Page 590: Point Of Interest By Category - Voice Recognition

Page 591: Set Home

Page 592: Additional Features

Page 593: Traffic

Page 594: Weather

This manual is also suitable for:

Toyota 2015 Corolla Owner's Manual

Screen Configurations

Traffic Event List

Predictive Traffic Map

Automatically Avoid Traffic

Quick Links

Related Manuals for Toyota 2015 Corolla

Summary of Contents for Toyota 2015 Corolla

This manual is also suitable for:

Table of Contents