Set Mode - Yaesu FT-252 Operating Manual

The FT-252 Set Mode, already described in parts of many previous chapters, is easy to
activate and set. It may be used for configuration of a wide variety of transceiver param-
eters, some of which have not been detailed previously. Use the following procedure to
activate the Set Mode:
1. Press the [ SET/ATS ] key to enter the Set mode.
2. Rotate the DIAL knob or press the [ p ] / [ q ] key to select
the Set Mode Item to be adjusted.
3. Press the [ SET/ATS ] key momentarily to enable adjust-
ment of the Set Mode Item.
4. Rotate the DIAL knob or press the [ p ] / [ q ] key to adjust or select the parameter to be
changed on the Set Mode Item selected in above step.
5. After completing your selection and adjustment, press the PTT switch momentarily
to save the new setting and exit to normal operation.
Some Set Mode Items (like Set Mode Item 42: TN FRQ) require that the [SET/ATS]
key be pressed after setting of the parameter, and before exiting to normal operation.
S M i F
et ode teM unction
1 [ ANI ]
Enables/Disables the ANI function. Setting of the Automatic
2 [ ANI.WRT ]
Program the ANI Identifier.
3 [ APO ]
Power-Off feature.
4 [ AR BEP ]
Selects the Beep option during ARTS operation.
5 [ ARS ]
Enables/Disables the Automatic Repeater Shift function.
6 [ BCLO ]
Enables/Disables the Busy Channel Lock-Out feature.
7 [ BEEP ]
Enables/Disables the beeper.
8 [ BELL ]
Selects the number of CTCSS/DCS Bell ringer repetitions.
9 [ CLK.SFT ]
Shifting of the CPU clock frequency.
10 [ CW WRT ]
Programs and activates the CW Identifier.
11 [ CWID ]
Enables/disables the CW identifier during ARTS operation.
12 [ DC VLT ]
Indicates the DC Supply Voltage.
13 [ DCS.COD ]
Setting of the DCS code.
14 [ DCS.N/R ]
Enables/Disables "Inverted" DCS code decoding.
15 [ DT DLY ]
Setting of the DTMF Autodialer Delay Time.
16 [ DT SPD ]
Setting of the DTMF Autodialer Sending Speed.
17 [ DT WRT ]
Programming of the DTMF Autodialer.
18 [ EDG.BEP ]
Enables/Disables the Band-edge beeper while selecting the
frequency via the DIAL knob.
19 [ EMG S ]
Selects the alarm(s) utilized when the Emergency function is
engaged.
20 [ F STEP ]
Setting of the synthesizer steps.
21 [ LAMP ]
Selects the LCD/Keypad Lamp mode.
22 [ LOCK ]
Selects the Control Locking lockout combination.
23 [ M/TCAL ]
Selects the [ VOL/SQL ] key function.
FT-252 O
peraTing
M
anual
Set ( Menu ) Mode
A
vAiLAbLe
( d
eFAuLt
ANI.OFF/ANI. ON
OFF / 0.5H - 12.0 H
INRANG / ALWAYS / OFF
ARS. ON / ARS.OFF
BCL. ON / BCL.OFF
KEY+SC / KEY / OFF
OFF / 1T / 3T /
5T / 8T / CONT
SFT.OFF / SFT. ON
TX OFF / TX ON
104 DCS codes (023)
T/RX N, RX R,
TX R, T/RX R
50MS / 100MS / 250MS /
450MS / 750MS / 1000MS
50MS / 100MS
BEP.OFF / BEP. ON
EMG.BEP / EMG.LMP / EMG.
B+L / EMG.CWT / EMG.C+B
/ EMG.C+L / EMG.ALL / OFF
5 / 10 / 12.5 / 15 / 20 / 25 / 50
/ 100 kHz, or AUTO
KEY / CONT / OFF
LK KEY / LKDIAL / LK K+D /
LK PTT / LK P+K /
LK P+D / LK ALL
MONI / T-CALL
v
ALueS
)
: B I
old talIc
---
---
---
---
53