Advertisement
UPPER REAR PANEL
6
8
INPUTS (5)
Two input channels are provided. The line-level input is of the medium impedance balanced type. The jack is a
combo female XLR and 1/4" TRS connector. Sensitivity of this input is 0.23 volts for full output, when the MIC/
LINE switch (7) is in the LINE position. Channel 2 has a 3.5 mm jack for mobile device signal sources.
GAIN (6) Present on both input Ch 1 and input Ch 2
Controls the gain or output level of the same numbered input channel. It is used to directly set the system output
level for a given input signal.
MIC/LINE switch (7) Present on both input Ch 1 and input Ch 2
Switches between LINE level gain (out position) and MIC level gain (in position). MIC position increases gain
26 dB to allow use of most dynamic microphones.
NOTE: Phantom power is not supplied on the INPUT (5) jacks
Gnd LIFT switch (8)
Allows the shield to be disconnected from the chassis ground to alleviate hum from ground loops
DIRECT THRU output jack (9)
This jack is intended for the use of linking multiple RBN™118 Sub's in a line, or to provide a feed to a powered
speaker, or other electronics that needs to receive a full range version of the input signal.
DIR/MIX switch (10)
Switches between Direct Thru from channel 1 input, or a mix of channel 1 and channel 2 at the Direct Thru out-
put (9)
HIGH PASS PROCESSED output jack (11)
Provides a filtered signal for use with full-range powered speaker systems like the RBN™112. Follow the in-
structions in the Setup Wizard in the RBN™118 Sub menu on the LCD screen using the Push-To-Select button
7
Advanced Digital Signal Processing
1
MIC
min
max
LINE
2
min
max
Gnd
LIFT
1
2
INPUTS
XLR: PIN 2 +
PIN 3
1/4": TIP +
RING
3.5mm: L/R SUMMED
5
WARNING:
SHOULD NOT BE EXPOSED TO RAIN OR MOISTURE AND OBJECTS FILLED WITH LIQUIDS,
SUCH AS VASES, SHOULD NOT BE PLACED ON THIS APPARATUS. TO PREVENT THE
AVIS:
DANS LE BUT DE REDUIRE LES RISQUES D'INCENDIE OU DE DECHARGE
ELECTRIQUE, CET APPAREIL NE DOIT PAS ETRE EXPOSE A LA PLUIE OU A L'HUMIDITE ET
AUCUN OBJET REMPLI DE LIQUIDE, TEL QU'UN VASE, NE DOIT ETRE POSE SUR CELUI-CI.
CAUTION
AVIS:
ELECTRIQUE-NE PAS OUVRIR
ON
POWER
FUSE
120V
T10AH/250V
FUSE
FUSE
220-240V
T5AH/250V
AC Cable
50/60Hz
200 WATTS
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
Consumo de energia
harmful interference, and (2) this device must accept any interference
200Wh
received, including interference that may cause undesired operation.
12
RBN SUB
TM
DIR
MIX
Input 1
1+2
MEDIA
IN
3.5mm
DIRECT THRU
OUTPUTS
9
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, THIS APPARATUS
RISK OF FIRE HAZARD, REPLACE WITH SAME TYPE 250 VOLT FUSE.
REMPLACER PAR UN FUSIBLE DE MEME TYPE ET DE 250 VOLTS.
Designed and Engineered in U.S.A.
Made in China
RISQUE DE CHOC
FOR 220-240V OPERATION, FUSE
MUST BE CHANGED TO T5AH/250V
220-240V
120V
FOR 120V OPERATION, FUSE
MUST BE CHANGED TO T10AH/250V
CAN-ICES-3(B)/NMB-3(B)
A.D.S.P.
Push to
Select
HIGH PASS
PROCESSED
DIRECT THRU
DIR
1
MIX
11
1
2
- - Laite on liitettävä suojamaadoituskoskettimilla
varustettun pistorasiaan. (For Finland only)
- - Apparatet må tilkoples jordet stikkontakt.
(For Norway only)
- - Apparaten skall anslutas till jordat uttag.
(For Sweden only)
13
10
Advertisement
