Blower Speed Selection - Rheem (-)802PA050314MSA Installation Instructions Manual

TABLE 12
IR FLOW PERFORM NCE – (-)802P/(-)(-)80MDP SERIES MODELS
Motor HP
Model Blower Size,
IN.
1/3
(-)802P 050314MS
(-)(-)80MDP050 30S
11 x 6
1/2
(-)802P 075417MS
(-)(-)80MDP075B30S
11 x 7
1/2
(-)802P 100521MS
(-)(-)80MDP100C40S
11 x 10
3/4
(-)802P 125524MS
(-)(-)80MDP125D50S
11 x 10
3/4
(-)802P 150524MS
(-)(-)80MDP150D50S
11 x 10
**Low Heating
*High Heating
The furnace controls have four active quick connect termi-
nals for connecting the motor speed leads. These are:
1. LO HEAT/FAN — motor runs on this speed when the
thermostat is in the "FAN ON" position or when low
stage heat (W) is energized.
2. COOL — connect desired cooling speed.
3. HI HEAT — connect desired high heating speed.
4. H/C (for heat/cool) — connect desired speed when
high heating and cooling speed are the same.
In addition to the active motor terminals, there are two
motor parking terminals (labeled M1 and M2) available for
placing any unused motor taps. All unused motor taps
should be connected to either M1 or M2. These terminals
(M1 and M2) will not be energized under any condition.
Speed Tap 0.1 0.2
Low** 823 803
Med. Lo* 1030 1018
Med. Hi 1129 1132
High 1361 1353
Low** 1229 1200
Med. Lo 1308 1267
Med. Hi* 1553 1542
High 1969 1924
Low** 1209 1182
Med. Lo* 1438 1420
Med. Hi 1902 1883
High 2071 2037
Low** 1358 1354
Med. Lo 1541 1517
Med. Hi* 1799 1774
High 2015 1989
Low** 1411 1395
Med. Lo 1606 1579
Med. Hi* 1889 1891
High 2178 2160
CFM ir Delivery
External Static Pressure, " W.C.
0.3 0.4 0.5
787 732 718
1006 976 929
1112 1087 1054
1331 1297 1264
1181 1155 1120
1266 1233 1204
1516 1491 1451
1893 1840 1803
1131 1112 1051
1386 1350 1320
1844 1817 1753
2001 1962 1905
1331 13091 1250
1476 1453 1416
1746 1712 1691
1929 1902 1862
1370 1334 1310
1569 1537 1499
1849 1828 1764
2105 2067 2024
IMPORTANT: Do not connect any motor speeds to "HI
HEAT" and/or "COOL" if you use the "HEAT/COOL" termi-
nal.
If cooling speed and fan speed are desired to be the same,
this may be accomplished by not connecting "Y" to the in-
tegrated furnace control.
See selection titled "Field Selections – Dipswitches" for
setting the heating and cooling blower off delay times.
0.6 0.7 0.8
691 651 593
897 850 808
1028 971 919
1232 1164 1117
1078 1013 970
1176 1113 1062
1417 1358 1306
1728 1657 1570
976 929 867
1293 1248 1186
1700 1636 1547
1856 1807 1709
1224 1154 1089
1371 1339 1277
1629 1554 1495
1815 1742 1665
1252 1220 1150
1468 1407 1346
1717 1659 1609
1976 1916 1832
47