Jumper Settings - Fujitsu SK-91465X-100PMC User Manual

Now connect the DC low voltage adapter to the Starter kit and plug in the In-Plug Power
Supply to a power socket. The SK-91465X-100PMC can be turned on with the on board
power switch S2.
For the power supply of the SK-91465XA-100PMC a DC input voltage of 12V is
recommended. The positive voltage (+) must be connected to the shield, and ground
(GND) must be connected to the centre of the connector X13!
After power-on of the SK-91465X-100PMC, the two red power-on LEDs D25 (5V) and D24
(3.3V) should be light. The LED D10 should light and the reset LED D1 should be off.

2.1 Jumper Settings

Jumper Description / Function
JP1 CAN A (TXD) / CAN4
JP2
JP3
JP4
JP5
JP6
JP7
JP8
JP9
JP10
JP11 CAN B (TXD) / CAN0
JP12
JP13 Reset immediate / delayed
JP14
JP15
JP16
JP17 X3 Shield – pin 5 (FlexRay B)
JP18
JP19 INH1 / INH2 FlexRay Channel A
JP20
JP21
JP22
JP23
JP24
JP25
JP26 UART A (RXD) / UART4
JP27
JP28
JP29 UART A (TXD) / UART4
JP30 X7 Shield – pin 5 (FlexRay A)
JP31 INH1 / INH2 FlexRay Channel B
JP32 LIN A Master-Mode
JP33
JP34
JP35 "WAKE" LIN-transceiver, LIN A
JP36
UG-910056-11
SK-91465X-100PMC User Guide
Chapter 2 Installation
AVcc
AVcc=AVRH
SW1 (INT0)
RX CAN A / CAN4
SW2 (INT1)
AVss
TX CAN A / CAN4
SW3 (ATGX)
SW4 (TIN0)
SW5 (TIN2)
RESET
RX CAN B / CAN0
TX CAN A / CAN4
SDA0 Pull-up
BM-B termination
BP-B termination
SCL0 Pull-up
X3 - GND / network
RTS-CTS A
INH / Vin
INHxA / INHxB
DTR/RTS A
DTR / DTRx
BM-A termination
BP-A termination
- 10 -
Default
Type
Setting
Solder JP 3 pin 1-2
Jumper 2 pin Closed
Jumper 2 pin Closed
Jumper 2 pin Closed
Jumper 2 pin Closed
Jumper 2 pin Closed
Jumper 2 pin Closed
Jumper 2 pin Closed
Jumper 2 pin Closed
Jumper 2 pin Closed
Solder JP 3 pin 1-2
Jumper 2 pin Closed
Solder JP 3 pin 1-2
Jumper 2 pin Closed
Jumper 2 pin Closed
Jumper 2 pin Closed
Jumper 2 pin Open
Jumper 2 pin Open
Jumper 3 pin 1-2
Jumper 2 pin Closed
Jumper 2 pin Closed
Jumper 2 pin Open
Jumper 3 pin 1-2
Jumper 2 pin Open
Jumper 3 pin 1-2
Jumper 2 pin Closed
Jumper 4 pin Closed
Jumper 3 pin Open
Jumper 2 pin Closed
Jumper 2 pin Open
Jumper 3 pin 1-2
Jumper 2 pin Open
Jumper 3 pin Open
Jumper 2 pin Closed
Solder JP 3 pin 1-2
Jumper 2 pin Closed
© Fujitsu Microelectronics Europe GmbH
Coordinates
J5
J22
J22
H10
J6
H10
J22
K6
G10
G10
J10
G10
E7
F9 / F8
K11
K11
E15
H21
F11
E14
E13
H21
E15
E5
H16
F14
H16
E5
F14
E11
E15
H12
H15
E10
G12
E9