Canon PIXMA MP610 Series Quick Start Manual page 113

~Important
When cleaning the exterior of the machine, use a soft cloth to wipe it gently. For detaiils, refer to "Cleaning Your Machine" in the Quick Start Guide.
1
Prepare the Machine
2
Install the Print Head
3
Install the Ink Tanks
4
Align the Print Head
Paper Guide
~
S
,...-----4- Paper Support
The pattern is printed. And Print Head is aligned
automatically.
WNote
Print Head alignment takes about 13 minutes to complete. Do
not start another operation until the machine has stopped making
operating noises.
WNote
• The pattern is printed in black and blue.
• When Automatic Print Head Alignment cannot be executed
correctly, the message "Auto head align has failed." is displayed
on the LCD. Refer to "An Error Message is Displayed on the LCD"
in the Quick Start Guide.
Hardware setup and Print Head alignment are
complete.
€) Make sure that Yes is selected in the message
requesting head alignment, then press the OK
button.
€} Load two sheets of supplied paper (MP-101) into
the Rear Tray with the printing side (whiter side)
facing up, align the paper with the Cover Guide
on the right side, then slide the Paper Guide
against the paper stack.
o
Pinch the Paper Guide and slide it to the left end.
Refer to the color
guide on the Print
Head Lock Lever
WNote
For the ink tanks compatible with this machine, refer to the back
cover of the Quick Start Guide.
~Important
• Do not touch the electrical contacts.
• Do not touch the ink port.
€)Insert the ink tank into the right-hand slot and
press the
8
mark on the ink tank until it clicks
into place.
€}
Twist off and discard the orange protective cap
located on the bottom of the ink tank.
~Important
• For your safety, always firmly grip the areas illustrated when
closing the Scanning Unit (Printer Cover).
• The machine starts the preparatory operation. It takes about 2
minutes. Do not start another operation until the machine has
stopped making operating noises.
~rProtectivecap
DOOO~~kPO"
Electrical Contacts
() Close the Inner Cover and the Scanning Unit
(Printer Cover).
o
Make sure the ink lamp lights red.
o
Pull the orange tape in the direction of the arrow
to peel off the protective film and remove the film
completely.
~~
A
Caution
There may be some transparent or light blue ink on the inside
of the bag the print head comes in, or the inside of the protec-
tive cap - this has no effect on print quality. Be careful not to
get ink on yourself when handling these items.
€} Remove the orange protective cap from the Print
Head and discard it.
~Important
If the Scanning Unit (Printer Cover) is left open for more than
10 minutes, the Print Head Holder moves to the right. Close
and reopen the Scanning Unit (Printer Cover) to return the
Holder to the center.
WNote
Do not touch the print head nozzles or the electrical contacts .
€) Firmly raise the Print Head Lock Lever until it
stops.The Print Head Lock Lever may feel heavy.
() Push the Print Head to hold it in place, and lower
the Print Head Lock Lever.
o
Insert the Print Head.
o
Remove the Print Head from its package.
~Important
• For your safety, always firmly grip the areas illustrated when
lifting the Scanning Unit (Printer Cover).
• Lift the Document Cover and Scanning Unit (Printer Cover)
together.
o
Open the Inner Cover. Write down the serial
number located inside the machine. You will need
this to register your product.
() Lift the Scanning Unit (Printer Cover) until it locks
into place. The Print Head Holder moves to the
center.
~Important
If an unintended language is displayed on the LCD, press the
Back button to return to the Language selection screen.
~Important
The Print Head and ink tanks are placed inside of the Paper
Output Tray.
€}
Plug the power cord in the back of the machine
and connect the other end to the wall outlet.
Next, open the Sheet Feeder Cover, pull out
the Paper Support, then open the Output Tray
Extension.
(2) Press the OK - - - ~
button.
~Important
Make sure that the Document Cover is closed.
(1) Press the .... or'"
button to select the
language.
€) Open the Operation Panel, then press the ONI
OFF button to turn on the machine.
Once the message "Install the print head and set the ink
tank." appears, go to
0.
o
Use the" or • button on the Operation Panel to
select the language for the LCD, then press the
OK button.
o
Open the Paper Output Tray with your hands,
and take out the Print Head and ink tanks.
A
Caution
Before turning on the machine, remove all the orange shipping
tapes.