Yamaha FT50C Service Manual page 259

Installing the lower unit .............................6-22
Installing the pinion ...................................6-22
Installing the power trim and tilt ................7-45
Installing the power unit ............................5-49
Installing the propeller shaft housing ........6-16
Installing the rocker arm assembly ...........5-33
Installing the sprockets and timing belt .....5-18
Installing the steering arm.........................7-23
Installing the upper case ...........................7-17
Installing the valves...................................5-32
Installing the water pump and shift rod .......6-9
L.
Lower unit .......................... 1-7
Lubricating the throttle gear ......................7-10
Lubrication ................................................3-16
M.
Maintenance interval chart..........................3-2
Maintenance specifications.........................2-3
Manual format .............................................1-1
Measuring the forward gear backlash.......6-27
Measuring the lower resistance ..................8-2
Measuring the peak voltage........................8-2
N.
Newly designed four carburetors ................1-5
P.
Parts, lubricants, and sealants....................1-3
Power trim and tilt .....................................1-19
Power trim and tilt electrical system..........7-47
Power trim and tilt motor ...........................7-43
Power trim and tilt unit .................... 3-11
Power unit ............................ 2-3
Predelivery checks....................................1-26
Propeller selection ....................................1-26
Propeller shaft housing .............................6-11
Propeller size ............................................1-26
R.
Refacing the valve seat.............................5-28
Removing and installing the oil filter .........5-37
Removing the clamp brackets...................7-19
Removing the cylinder head .....................5-24
Removing the drive shaft ..........................6-19
Removing the lower unit .............................6-6
Removing the power trim and tilt/
hydro tilt ..................................................7-26
Removing the power unit ..........................5-13
62Y5A11
S.
, , ,
2-6 3-12 6-5
T.
,
7-25
, , ,
3-4 5-3 9-1
U.
V.
Removing the propeller shaft housing
assembly ................................................ 6-13
Removing the starter motor pinion ........... 8-19
Removing the steering arm ...................... 7-23
Removing the timing belt and sprockets... 5-17
Removing the water pump and shift rod..... 6-9
Replacing the engine oil ............................. 3-4
Replacing the gear oil............................... 3-13
Replacing the valve guides....................... 5-26
Safety while working................................... 1-3
Selecting the connecting rod big end
bearing.................................................... 5-45
Selecting the crankshaft main journal
bearing.................................................... 5-45
Selecting the forward gear shims ............. 6-26
Selecting the pinion shims........................ 6-25
Selecting the reverse gear shims ............. 6-27
Selection................................................... 1-26
Self-protection ............................................ 1-3
Serial number ............................................. 1-4
Shimming.........................................6-24
Special service
,
tools .................... 3-1 4-1
Specified torques...................................... 2-14
Starboard and port views............................ 8-3
Starter motor............................................. 8-17
Starting system......................................... 8-15
Swivel bracket and steering arm .............. 7-21
Symbols...................................................... 1-2
Synchronizing the carburetors.................. 4-14
Technical tips.............................................. 1-8
Test run .................................................... 1-29
Tightening torques.................................... 2-14
Tiller handle ................................................ 7-2
Tiller handle model ..................................... 8-6
Tilt cylinder and trim cylinder .................... 7-27
Timing belt and sprockets......................... 5-16
Top cowling ................................................ 3-3
Top view ..................................................... 8-5
Trim cylinder ............................................. 7-29
Upper case ............................................... 7-11
Use of leaded gasoline ............................... 1-5
Ventilation................................................... 1-3
1
2
3
4
,
6-25
5
, , , ,
5-1 6-1 7-1 8-1
6
7
8
9
i-3