Mitsubishi SL1U User Manual page 32

ITEM
SPLASH SCREEN
BACK COLOR
LAMP MODE
IMAGE REVERSE
MENU POSITION
EXPAND MODE
AUDIO MODE
VIDEO SIGNAL
ANAMORPHIC
LANGUAGE
RESET ALL
MEMORY CALL
HORIZ. POSITION
VERT. POSITION
FINE SYNC.
TRACKING
COMPUTER INPUT
HOLD
HOLD BEGIN
HOLD END
CLAMP POSITION
CLAMP WIDTH
HORIZ. PIXELS
VERT LINES
VERT.SYNC
SHUTTER (U)
SHUTTER (L)
SHUTTER (LS)
SHUTTER (RS)
MUTE
How to set the grade
Use ASCII letters code to set the grade for setting data. Please refer to the table below for HEX code.
ASCII '+' '–'
HEX 2Bh 2Dh
[Example 1] Set the AUTO POWER ON to ON.
Sending commands
from the PC etc.
30 30 41 50 4F 4E 31 0D
'0' '0' 'A' 'P' 'O' 'N' '1' '
The data code of CONTRAST and BRIGHTNESS is structured by the difference data of R from G, the main data and
the difference data of B from G.
[Example 2] Set the difference data of R from G to +10, the setting main data to 0 and the difference data of
B from to -5.
Sending commands
from the PC etc.
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D
'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' '
[Example 3] The TINT was set to +10 when the setting status was confirmed.
Sending commands
from the PC etc.
30 30 53 0D
'0' '0' 'S' ' '
ASCII HEX
SS 53h 53h
BB 42h 42h
LM 4Ch 4Dh
IR 49h 52h
MP 4Dh 50h
EX 45h 58h
AU 41h 55h
VS 56h 53h
SC 53h 43h
LG 4Ch 47h
RSTALL 52h 53h 54h 41h 4Ch 4Ch
MMC 4Dh 4Dh
HP 48h 50h
VP 56h 50h
FN 46h 4Eh
TRK 54h 52h
CIN 43h 49h
HLD 48h 4Ch
HLB 48h 4Ch
HLE 48h 4Ch
CLP 43h 4Ch
CLW 43h 4Ch
HPL 48h 50h
VLN 56h 4Ch
VSC 56h 53h
SHU 53h 48h
SHL 53h 48h
SHLS 53h 48h
SHRS 53h 48h
MUTE 4Dh 55h
'0' '1' '2' '3'
30h 31h 32h 33h
'
30 30 41 50 4F 4E 31 0D
'0' '0' 'A' 'P' 'O' 'N' '1' '
'
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D
'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' '
30 30 53 2B 31 30 0D
'0' '0' 'S' '+' '1' '0' '
VALUE
0 (OFF), 1 (ON)
0 (BLACK), 1 (BLUE)
0 (STANDARD), 1 (LOW)
0 (OFF), 1 (Mirror), 2 (Invert), 3 (Mirror invert)
0 (Upper left), 1 (Lower right)
1 - 2
1 (COMPUTER), 2 (VIDEO), 3 (COMPUTER & VIDEO), 4 (MUTE)
0 (AUTO), 1 (NTSC), 2 (PAL), 3 (SECAM) ,
4 (4.43NTSC), 5 (PAL-M), 6 (PAL-N), 7 (PAL-60)
0 (OFF), 1 (ON)
0 ( ), 1 (English), 2 (Español), 3 (Deutsch) ,
4 (Frençais), 5 (Italiano), 6 (
43h 0 (AUTO), 1 (USER1), 2 (USER2)
+ (increase), – (decrease)
+ (increase), – (decrease)
00 - 39
4Bh + (increase), – (decrease)
4Eh 0 (RGB), 1 (YC
44h 0 (AUTO), 1 (ON), 2 (OFF)
42h –01 - –99
45h 01 - 99
50h 00 - 63
57h 01 - 63
4Ch 0000 - 9999
4Eh 0000 - 9999
43h 0 (AUTO), 1 (ON), 2 (OFF)
55h 000 - 383 (000 - 299 for SL1U)
4Ch 000 - 383 (000 - 299 for SL1U)
4Ch 53h 000 - 510 (000 - 398 for SL1U)
52h 53h 000 - 510 (000 - 398 for SL1U)
54h 45h 0 (MUTE OFF), 1 (MUTE ON)
'4' '5' '6' '7'
34h 35h 36h 37h
Status code from
projector
'
Status code from
projector
Status code from
projector
'
4
)
C /YP P )
B R B R
'8' '9'
38h 39h
Meaning
Command for setting the
AUTO POWER ON to ON
Command received
(Command echo back)
Meaning
Command for setting the
picture control
Command received
' (Command echo back)
Meaning
Command to confirm
setting of TINT
Command (setting of TINT
is +10) carried out