Mitsubishi SL1U User Manual page 16

Menu operation (continued)
1 IMAGE
CONTRAST ......... Adjusts the picture contrast. The contrast becomes higher as the
number increases.
BRIGHTNESS ..... Adjusts the image brightness. The image becomes brighter as
the number increases.
sRGB .................... Select ON to display an image emphasizing on the color
reproducibility.
• When sRGB is ON, COLOR MATRIX, can't be adjusted.
• When sRGB is ON, the image will become darker.
• When COLOR TEMP is set to other than STANDARD
• Though sRGB can be ON while a signal is input from
COLOR MATRIX ......... Adjusts the color balance in each color of the image. See page 18.
COLOR TEMP. .... Adjusts the color temperature. See page 18.
COLOR ................ Adjusts the color intensity of the image. (Available only when VIDEO is selected as the source.)
TINT .................... Adjusts the color balance of the image. The color balance of the image shifts green as the number
increases and shifts to purple as the number decreases. (Available only when VIDEO is selected as the
source.)
• When the TV50 (PAL, SECAM) signal is inputted, TINT can't be adjusted.
SHARPNESS ....... Adjusts the image sharpness. The image sharpness rises as the number increases.
2 INSTALLATION
IRIS ...................... Adjusts the sensitivity of the function (IRIS) which
automatically adjusts the brightness and contrast of the image
depending on the degree of the light in the room. When using
this projector in a room where the light and shade varies
slightly, select 1. When using this projector in a normally
lighted room, select 2. When using this projector in a room
where the light and shade varies greatly, select 3.When you
select OFF, IRIS won't operate.
• When the sensitivity is adjusted in a large amount, the
KEYSTONE ......... Corrects keystone distortion. Select an optimum value for
proper display. For normal use, select 0˚.
AUTO POWER ON ...... Select ON to boot up the projector automatically by turning on an externally connected power switch
such as a breaker even when the main power switch of the projector is off. Use this setting when the
projector is hanging from the ceiling.
• The projector will be in the stand-by mode when the lamp is off. Use the remote control to turn
AUTO POWER OFF .... Set the time elapsed before the projector enters into the stand-by mode when there is no signal
inputted from the selected source.
SPLASH SCREEN ....... Select ON to display the splash screen when the power is turned ON.
BACK COLOR ...... Use to select the color of the background, blue or black, which will be displayed when there is no signal
inputted from the selected source.
LAMP MODE ....... Use to change the brightness of the lamp. When LOW is selected, the image will become darker,
though the power will be saved, operating sound will be reduced.
• The brightness of the lamp will be STANDARD for 3 minutes regardless of the setting of the LAMP
• When the LAMP MODE is changed, the screen may flicker. This is not a failure of the lamp.
IMAGE REVERSE ...... Use to reverse or invert the projected image. Select MIRROR in rear projection. Select MIRROR,
INVERT in rear projection with the projector hanging from the ceiling.
3 FEATURE
MENU POSITION ....... Use to select the position of the menu on the screen,
left) or
EXPAND MODE .. Select the mode for enlarging screen. See page 20.
AUDIO MODE ..... Select COMPUTER to output the sound which is inputted to
the audio input terminal when COMPUTER is selected as the
source. Select VIDEO to output the sound which is inputted to
the audio input terminal when VIDEO is selected as the source.
Select COMPUTER VIDEO mode to always output the sound
which is inputted to the audio input terminal. Select MUTE not
to output the sound at all.
EN – 16
while sRGB is ON, colors won't be reproduced as per
the standard value of sRGB.
VIDEO-IN or S-VIDEO IN, reproduced colors won't be
in accordance with the sRGB standard value. Use sRGB to suit your color preference.
image may be displayed solid white. Adjust the
sensitivity depending on the operating environment
and imges to be displayed.
on the lamp.
MODE when the lamp turns on.
(lower right).
opt.
IMAGE
CONTRAST
BRIGHTNESS
sRGB
COLOR MATRIX
COLOR TEMP.
COLOR
TINT
SHARPNESS
opt.
INSTALLATION
IRIS
KEYSTONE
AUTO POWER
ON
AUTO POWER
OFF
SPLASH SCREEN
ON
BACK COLOR
LAMP MODE
IMAGE REVERSE
(upper
opt.
FEATURE
MENU POSITION
A
EXPAND MODE
A
AUDIO MODE
?
VIDEO SIGNAL
ANAMORPHIC
A LANGUAGE
Ë
RESET ALL
XGA60
0
0
OFF
COMPUTER
STANDARD
0
0
0
XGA60
OFF
0˚
OFF
OFF
ON
BLUE
STANDARD
OFF
XGA60
1.
1.
COMPUTER
VIDEO
AUTO
OFF
English
OK