Chapter 4 Getting Acquainted; Front Panel - Kenwood TS-2000 Instruction Manual

GETTING ACQUAINTED

FRONT PANEL

1
PF
F LOCK A
3
4
5
6
7
8
9
10
q PF key
You can assign a function to this Programmable
Function key. The default function is Voice 1
{page 77}.
w [
] (POWER) switch
Press and hold briefly to switch the transceiver power
ON. Press again to switch the power OFF.
e ATT/ F LOCK key
Press to switch the receiver attenuator ON or OFF
{page 57}. Press [FUNC], [ATT/ F LOCK] to switch
the Frequency Lock function ON or OFF {page 77}.
r PRE/ LOCK A key
Press to switch the receiver pre-amplifier ON or OFF
{page 57}. Press [FUNC], [PRE/ LOCK A] to lock all
the transceiver keys {page 77}.
t VOX/ LEVEL key
In voice mode, press to switch the Voice-Operated
Transmit function ON or OFF {page 39}. In CW
mode, press to switch the Break-in function ON or
OFF {page 42}. Press [FUNC], [VOX/ LEVEL] to
adjust the microphone input level for VOX operation.
The VOX LED lights orange when the VOX function is
active.
y PROC/ LEVEL key
Press to switch the Speech Processor for transmitting
ON or OFF {page 40}. Press [FUNC],
[PROC/ LEVEL] to adjust the Speech Processor
input level. The PROC LED lights orange when the
Speech Processor function is actived.
u SEND key
Press to switch the transceiver between receive
mode and transmit mode {pages 5, 7}.
8
2
MAIN
AUTO
CAR
LSB
USB
MIC
REV
TX MONI
CW
PWR
FSK
DELAY
NAR
FM
KEY
AM
CLR
SEL
DISP 1MHz
11 13
12
HF/VHF/UHF ALL MODE MULTI BANDER TS-2000
SUB
MENU
TF-
SET
MAIN SUB
SG.SEL
CTRL M.IN
SCAN
M VFO
i AT/ ANT1/2 key
Press to activate the internal antenna tuner {page 72}
or an external antenna tuner. Press [FUNC],
[AT/ ANT1/2] to select either Antenna 1 or Antenna 2
for the HF/ 50 MHz band {page 72}.
o PHONES jack
Connect a set of headphones to this jack. Inserting a
plug into the jack automatically mutes the audio from
the speaker {pages 3, 78}.
!0 MIC connector
Connect a compatible microphone to this connector,
then securely screw down the connector locking ring
{page 3}.
!1 N.R./ LEVEL key
Press to switch the DSP Noise Reduction function
ON or OFF. Press [FUNC], [N.R./ LEVEL] to adjust
the Noise Reduction level. Press [FUNC],
[N.R./ LEVEL] again to finish the adjustment
{page 56}.
!2 A.N./ LEVEL key
Press to switch the DSP Auto Notch function ON or
OFF. Press [FUNC], [A.N./ LEVEL] to adjust the
DSP Auto Notch reduction level. Press [FUNC],
[A.N./ LEVEL] again to finish the adjustment
{page 56}.
!3 B.C./ MANUAL key
Press to switch the DSP Auto Beat Cancel function
ON or OFF. Press [FUNC], [B.C./ MANUAL] to
adjust the beat cancel frequency manually. Press
[FUNC], [B.C./ MANUAL] again to finish the manual
adjustment {page 56}.
9.6k STA CON
CW TUNE
RIT
RIT/SUB
ALT
XIT
_
+
CLEAR
P.C.T
SET