Streaming Music Over The Network - Panasonic CS-PMX100 Operating Instructions Manual

Wired LAN connection
Method 4:
Using a LAN cable
e.g.,
Broadband router, etc.
LAN cable
(not supplied)
1
Disconnect the AC mains lead.
2
Connect the main unit to a broadband router, etc.
using a LAN cable.
3
Connect the AC mains lead to the main unit and
turn this system on.
• When the connection is established, "
on the main unit's display.
Note:
• Use category 5 or above straight LAN cables (STP) when
connecting to peripheral devices.
• The LAN cable must be connected or disconnected while
the AC mains lead is disconnected.
• Inserting any cable other than a LAN cable in the LAN port
can damage the system.
• If the LAN cable is disconnected, the network-related
settings ( right) will be initialized. In that case, make the
settings again.
• When a LAN cable is connected, the Wi-Fi function will be
disabled.
8
To make network-related settings
You can change this system's name on the network,
change the security options for this system, and use
specific IP address, subnet mask, default gateway,
primary DNS, etc.
You can also change the name of this system by
changing a setting in the app "Panasonic Music
Streaming" (version 2.0.8 or later) (
details on the app, refer to the site below.
http://panasonic.jp/support/global/cs/audio/app/
(This site is in English only.)
Preparation
• Complete the network settings. (
• Connect your device to the same network as this
system.
• Check this system's IP address (
down.
1
Start an Internet browser on your device and
then type this system's IP address into the
address field to display the settings page.
• It may take a few minutes until the settings page is
displayed depending on the environment. In that case,
reload the browser.
• If the unit is connected with Wi-Fi, only the device
" is indicated name and the security options for this system can be
changed. Close the settings page after making the
changes.
– To change the device name, select "Change", and
type a new device name, and then select "Apply".
– To change the security options for this system, select
"Change" for the AirPlay password setting.
If you have set an AirPlay password previously, you
will need your old password before making changes.
Make the changes and then select "Apply".
2
Type a device name and then select "Next".
• Refer to the step 7 of "Using an Internet browser" (
for details on a device name.
3
Select your security options for this system.
• Refer to the step 8 of "Using an Internet browser" (
for details on security options for this system.
4
Select and input the details.
• If your network requires specific settings, deselect
"DHCP" to disable DHCP.
– You can use specific IP address, subnet mask,
default gateway, primary DNS, etc.
5
Select "Connect" to apply the settings.
• When the connection is established, "Success"
appears on the main unit's display.

Streaming music over the network

You can stream music from your devices or online music
services to this system's speakers and other AllPlay
speakers.
You can also stream music source of this system to other
AllPlay speakers.
Streaming music on network devices
right). For
You can use the AllPlay or the DLNA function to stream
music from the device on the network to this system's
speakers by using the app "Panasonic Music Streaming"
(free of charge), etc.
• [iOS] : App Store
6)
• [Android] : Google Play™
Preparation
18), and note it • Complete the network settings.
( 6)
• Connect the following devices to the same network as
this system.
– Device with "Panasonic Music Streaming", etc.
installed
– Device containing music
The following steps are based on "Panasonic Music
Streaming".
1
Turn this system on.
• Check that "
• If it is not indicated, check the network settings. (
2
Start the app "Panasonic Music Streaming".
• Always use the latest version of the app.
3
Select a music source.
• To add music source, select "+ My Music Network" and
then select the device containing music.
– The added music source is numbered in order from 1.
6)
4
Select a song.
5
From "Select Speaker", select this system as the
output speakers.
7)
e.g.,
• If you have multiple AllPlay speakers, you can enjoy
synchronized sound from them. Select "
then select the speakers to group.
" is indicated on the display.
6)
My room
" and