Page 1 2010 Chevrolet Colorado Owner Manual In Brief ..........1-1 Instrument Panel .
Page 2 2010 Chevrolet Colorado Owner Manual Vehicle Identification ......6-111 Customer Assistance Information ....8-1 Electrical System .
Page 3: Canadian Owners
General Motors of Canada index in the back of the manual. It is an alphabetical list Limited for Chevrolet Motor Division wherever it of what is in the manual and the page number where it can be found.
Page 4: Vehicle Symbols
Safety Warnings and Symbols A circle with a slash through it is a safety Warning messages found on vehicle labels and in this symbol which means Do manual describe hazards and what to do to avoid or Not, Do not do this, or reduce them.
Page 5: Index
Vehicle Symbol Chart : Fog Lamps Here are some additional symbols that may be found on : Fuel Gauge the vehicle and what they mean. For more information : Fuses on the symbol, refer to the index. : Headlamp High/Low-Beam Changer : Airbag Readiness Light : LATCH System Child Restraints : Air Conditioning...
Page 6 NOTES I n f o r ma t i o n P r o v i d e d b y :...
Page 7: In Brief
Section 1 In Brief Vehicle Features ........1-15 Instrument Panel .
Page 8 Instrument Panel Manual Transmission shown, Automatic Transmission similar I n f o r ma t i o n P r o v i d e d b y :...
Page 9 A. Outlet Adjustment on page 4 18. H. Horn on page 4 3. ® B. Turn Signal/Multifunction Lever on page 4 4. I. StabiliTrak System on page 5 6 and Four-Wheel Drive on page 3 28. C. Instrument Panel Cluster on page 4 18. J.
Page 10: Initial Drive Information
Initial Drive Information Press to sound the horn and to flash the exterior lamps for 30 seconds. This section provides a brief overview about some of the important features that may or may not be on your Lock and unlock feedback can be personalized. specific vehicle.
Page 11 Power Door Locks Tailgate Press L or U on the switch on the armrest to lock or unlock the doors. Open the tailgate by pulling up on the outside handle For more information see: while pulling the tailgate down. Door Locks on page 3 7 On vehicles with a locking tailgate, use the ignition key to unlock it.
Page 12 Windows Power Windows Manual Windows Use the window crank to open and close each window. Press or pull up on the front of the switch to open or close the window. For more information see: Manual Windows on page 3 13 Power Windows on page 3 13 I n f o r ma t i o n P r o v i d e d b y :...
Page 13: Seat Adjustment
Seat Adjustment Power Seats Manual Seats To adjust the seat using the control on the outboard side of it: 1. Lift the bar to unlock the seat. Slide the horizontal control forward or rearward. 2. Slide the seat to the desired position and release Move the front or rear of the horizontal control up the bar.
Page 14: Reclining Seatbacks
Reclining Seatbacks Power Lumbar Press and hold the front or rear of the control on the outboard side of the seat until you have the desired Use the vertical control on the outboard side of the seat lumbar support. to raise or recline the seatback by moving the control For more information see: forward or rearward.
Page 15: Heated Seats
Heated Seats Safety Belt With the ignition on, press the top of the switch on the outboard side of the seat to turn the heat on at the high Refer to the following sections for important information setting. on how to use safety belts properly. Press the bottom of the switch to turn the heat to the Safety Belts: They Are for Everyone on page 2 14.
Page 16: Sensing System For Passenger Airbag
Sensing System for Passenger Airbag The passenger sensing system, if equipped, will turn off the right front passenger frontal airbag under certain conditions. The driver airbags are not affected by this. If the vehicle has one of the passenger airbag status United States Canada indicators pictured in the following illustrations, then the...
Page 17: Mirror Adjustment
Mirror Adjustment 2. Press one of the four buttons located on the control pad to move the mirror to the desired Exterior Mirrors direction. 3. Return the selector switch to the center position Vehicles with power once the mirrors are adjusted. outside mirrors have Manually fold the mirrors inward to prevent damage controls located on the...
Page 18: Steering Wheel Adjustment
Steering Wheel Adjustment Interior Lighting Dome Lamps The dome lamps, located in the front and cargo area of the vehicle, come on when any door is opened. Turn the dome lamps on by turning the thumbwheel, located next to the exterior lamps control, all the way up.
Page 19: Exterior Lighting
Exterior Lighting ;: Manual operation of the parking lamps and other exterior lamps. 2: Manual operation of the headlamps and other exterior lamps. For more information, see: Exterior Lamps on page 4 10 Daytime Running Lamps (DRL) on page 4 11 Automatic Headlamp System on page 4 12 Fog Lamps on page 4 12 Exterior Cargo Lamps on page 4 13...
Page 20: Climate Controls
Windshield Wiper/Washer Climate Controls 8: Use for a single wiping cycle. A. Temperature Control D. Air Conditioning N: Delays wiping cycle. Move the band to adjust the B. Fan Control E. Air Recirculation frequency of wipes. C. Air Delivery Mode 6 : Slow wipes.
Page 21: Vehicle Features
Vehicle Features TUNE : Turn to select radio stations. SEEK : Press to go to the previous or to the next Radio(s) station and stay there. For more information about these and other radio features, see Audio System(s) on page 4 41. Setting Preset Stations Radio stations are stored as presets.
Page 22: Setting The Clock
Setting the Clock Satellite Radio To set the time and date for the radio with CD XM is a satellite radio service that is based in the (MP3/WMA): 48 contiguous United States and 10 Canadian provinces. XM satellite radio has a wide variety of Press and hold the HR button until the correct hour programming and commercial-free music, displays.
Page 23: Cruise Control
Driver Information Center (DIC) Cruise Control The DIC is located on the instrument panel cluster. The cruise controls are It displays the status of many vehicle systems and located at the end of the enables some features to be personalized. multifunction lever.
Page 24: Performance And Maintenance
® Power Outlets StabiliTrak The accessory power outlets can be used to connect The Electronic Stability Control system assists with electrical equipment, such as a cellular phone. directional control of the vehicle in difficult driving conditions. The system turns on automatically every The vehicle may have an accessory power outlet time the vehicle is started.
Page 25 Tire Pressure Monitor You may notice during cooler conditions that the low tire pressure warning light will appear when the vehicle is This vehicle may have a Tire Pressure Monitor first started and then turn off as you drive. This may be System (TPMS).
Page 26: Driving For Better Fuel Economy
Engine Oil Life System Driving for Better Fuel Economy The engine oil life system calculates engine oil life Driving habits can affect fuel mileage. Here are some based on vehicle use and displays a DIC message driving tips to get the best fuel economy possible. when it is necessary to change the engine oil and filter.
Page 27 U.S.: 1-800-CHEV-USA (1-800-243-8872) TTY Users: 1-888-889-2438 Canada: 1-800-268-6800 As the owner of a new Chevrolet, you are automatically enrolled in the Roadside Assistance program. This program provides technically trained advisors who are available 24 hours a day, 365 days a year, minor repair information or towing arrangements.
Page 28: How Onstar Service Works
How OnStar Service Works For a full description of OnStar services and system limitations, see the OnStar Owner's Guide in the : This blue button connects you to a specially glove box. trained OnStar advisor to verify your account OnStar service is subject to the OnStar terms and information and to answer questions.
Page 29: Your Responsibility
Your Responsibility This information usually includes the vehicle's GPS location and, in the event of a crash, additional Increase the volume of the radio if the OnStar advisor information regarding the crash that the vehicle was cannot be heard. involved in (e.g. the direction from which the vehicle was hit).
Page 30 NOTES 1-24 I n f o r ma t i o n P r o v i d e d b y :...
Page 31: Table Of Contents
Section 2 Seats and Restraint System Lower Anchors and Tethers for Children Front Seats ......... 2-2 Manual Seats .
Page 32: Front Seats
Front Seats If the vehicle has a manual seat, it can be moved forward or rearward. Manual Seats 1. Lift the bar to unlock the seat. 2. Slide the seat to the WARNING: desired position and release the bar. You can lose control of the vehicle if you try to adjust a manual driver's seat while the vehicle is moving.
Page 33 Power Seats To adjust the seat: Move the seat forward or rearward by sliding the If the vehicle has power horizontal control forward or rearward. seats, the controls used to operate them are located Raise or lower the front part of the seat cushion by on the outboard side of moving the front of the horizontal control up the seats.
Page 34: Manual Lumbar
Manual Lumbar Power Lumbar On vehicles with this If the vehicle has this feature, the knob is feature, the control is located on the outboard located on the outboard side of the driver seat. side of the seat(s). Press and hold the front of the control until you have the desired lumbar support.
Page 35 Heated Seats This feature will heat the cushion and back of the seats. Press HI to turn the heat to the high setting. Press LO If the vehicle has this to turn the heat to the low setting. Put the switch in the feature, the controls are center position to turn the heat off.
Page 36: Manual Reclining Seatbacks
Reclining Seatbacks WARNING: Manual Reclining Seatbacks If either seatback is not locked, it could move WARNING: forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they You can lose control of the vehicle if you try to are locked.
Page 37 To return the seatback to an upright position: 1. Lift the lever fully without applying pressure to the seatback and the seatback will return to the upright position. 2. Push and pull on the seatback to make sure it is locked.
Page 38: Power Reclining Seatbacks
Power Reclining Seatbacks WARNING: If the seats have power reclining seatbacks, use the vertical power seat Sitting in a reclined position when the vehicle is in control located on the motion can be dangerous. Even when buckled up, outboard side of the seat. the safety belts cannot do their job when reclined like this.
Page 39: Head Restraints
Head Restraints The front seats may have adjustable head restraints. If the vehicle has rear seats, they may have adjustable head restraints. Do not have a seatback reclined if the vehicle is moving. Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant's head.
Page 40: Seatback Latches
Pull up on the head To fold the seatback restraint to raise it. To forward, push the lever on lower the head restraint, the side of the seat press the button located rearward and pull the on top of the seatback seatback forward.
Page 41: Rear Seats
Rear Seats To store the seat: Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the Rear Seat Operation (Extended Cab) safety belts. Always unbuckle the safety belts and return them to their normal stowed position before If the vehicle has an folding a rear seat.
Page 42: Rear Seat Operation (Crew Cab)
Rear Seat Operation (Crew Cab) To fold the rear seatback(s) forward: The rear seatback(s) in the crew cab can be folded forward. Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts.
Page 43 2. Make sure the seatback(s) is locked by pushing 2. Pull the loop, located and pulling on it. on the outboard side of the seatback, forward until you hear a click. WARNING: A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection needed in a crash.
Page 44: Safety Belts
Safety Belts WARNING: Safety Belts: They Are for Everyone People riding on the tailgate (if equipped) can This part of the manual tells you how to use safety belts easily lose their balance and fall even when the properly. It also tells you some things you should not do vehicle is operated at low speeds.
Page 45: Why Safety Belts Work
Why Safety Belts Work In most states and in all Canadian provinces, the law requires wearing safety belts. Here is why: When you ride in or on anything, you go as fast as You never know if you will be in a crash. If you do have it goes.
Page 46 Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop. 2-16 I n f o r ma t i o n P r o v i d e d b y :...
Page 47 The person keeps going until stopped by something. In or the instrument panel... a real vehicle, it could be the windshield... I n f o r ma t i o n P r o v i d e d b y : 2-17...
Page 48: Questions And Answers About Safety Belts
Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt? A: You could be whether you are wearing a safety belt or not. But your chance of being conscious during and after an accident, so you can unbuckle and get out, is much greater if you are belted.
Page 49: How To Wear Safety Belts Properly
How to Wear Safety Belts Properly Q: If I am a good driver, and I never drive far from home, why should I wear safety belts? This section is only for people of adult size. A: You may be an excellent driver, but if you are in a Be aware that there are special things to know about crash even one that is not your fault...
Page 50 In a crash, this applies force to the strong pelvic bones and you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force on your abdomen. This could cause serious or even fatal injuries.
Page 51 Q: What is wrong with this? WARNING: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should fit snugly against your body. A: The shoulder belt is too loose.
Page 52 Q: What is wrong with this? WARNING: You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen. This could cause serious or even fatal injuries. The lap belt should be worn low and snug on the hips, just touching the thighs.
Page 53 Q: What is wrong with this? WARNING: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones. This could cause serious internal injuries.
Page 54 Q: What is wrong with this? WARNING: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries.
Page 55 Q: What is wrong with this? WARNING: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury. Also, the belt would apply too much force to the ribs, which are not as strong as shoulder bones.
Page 56 Q: What is wrong with this? WARNING: You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury.
Page 57 Q: What is wrong with this? WARNING: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer/retailer to fix it.
Page 58: Lap-Shoulder Belt
Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt except for the center front passenger position, if equipped, which has a lap belt. See Lap Belt on page 2 34 for more information. The following instructions explain how to wear a lap-shoulder belt properly.
Page 59 To unlatch the belt, push the button on the buckle. The 5. To make the lap part tight, pull up on the belt should return to its stowed position. Slide the latch shoulder belt. plate up the safety belt webbing when the safety belt is It may be necessary to pull stitching on the safety not in use.
Page 60 Shoulder Belt Height Adjuster Safety Belt Pretensioners The vehicle has a shoulder belt height adjuster for the This vehicle has safety belt pretensioners for front driver and right front passenger seating position. outboard occupants. Although the safety belt pretensioners cannot be seen, they are part of the Adjust the height so that the shoulder portion of the belt safety belt assembly.
Page 61: Rear Safety Belt Comfort Guides
Rear Safety Belt Comfort Guides Here is how to install a comfort guide to the shoulder belt. This vehicle may have rear shoulder belt comfort guides for the rear outside positions. If not, they are available through your dealer/retailer. Rear shoulder belt comfort guides may provide added safety belt comfort for older children who have outgrown booster seats and for some adults.
Page 62 2. Place the guide over the belt and insert the two 3. Be sure that the belt is not twisted and it lies flat. edges of the belt into the slots of the guide. The elastic cord must be under the belt and the guide on top.
Page 63 WARNING: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces.
Page 64: Safety Belt Use During Pregnancy
Safety Belt Use During Pregnancy Lap Belt Safety belts work for everyone, including pregnant This section is only for the lap belt. To learn how to women. Like all occupants, they are more likely to be wear a lap-shoulder belt, see Lap-Shoulder Belt on seriously injured if they do not wear safety belts.
Page 65: Safety Belt Extender
Safety Belt Extender If the vehicle's safety belt will fasten around you, you should use it. But if a safety belt is not long enough, your dealer/ retailer will order you an extender. When you go in to order it, take the heaviest coat you will wear, so the extender will be long enough for you.
Page 66: Child Restraints
Child Restraints The manufacturer's instructions that come with the booster seat, state the weight and height limitations for that booster. Use a booster seat with a lap-shoulder belt Older Children until the child passes the below fit test: Sit all the way back on the seat. Do the knees bend at the seat edge? If yes, continue.
Page 67 Q: What is the proper way to wear safety belts? WARNING: A: An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face Never do this. or neck.
Page 68: Infants And Young Children
WARNING: Never do this. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, the child would not be restrained by the shoulder belt.
Page 69 WARNING: WARNING: (Continued) Children can be seriously injured or strangled if a during a crash. For example, in a crash at only shoulder belt is wrapped around their neck and 40 km/h (25 mph), a 5.5 kg (12 lb) infant will the safety belt continues to tighten.
Page 70 WARNING: Never do this. Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat.
Page 71 Q: What are the different types of add-on child restraints? WARNING: (Continued) A: Add-on child restraints, which are purchased by the vehicle's owner, are available in four basic types. and its head weighs so much compared with Selection of a particular restraint should take into the rest of its body.
Page 72: Child Restraint Systems
Child Restraint Systems A rear-facing infant seat (A) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint. A booster seat (C-D) is a child restraint designed to improve the fit of the vehicle's safety belt system.
Page 73 Securing an Add-On Child Restraint in To help reduce the chance of injury, the child restraint must be secured in the vehicle. Child restraint systems the Vehicle must be secured in vehicle seats by lap belts or the lap belt portion of a lap-shoulder belt, or by the LATCH system.
Page 74: Where To Put The Restraint
Securing the Child Within the Child WARNING: Restraint A child in a rear-facing child restraint can be WARNING: seriously injured or killed if the right front passenger airbag inflates. This is because the A child can be seriously injured or killed in a crash back of the rear-facing child restraint would be if the child is not properly secured in the child very close to the inflating airbag.
Page 75 Do not use child restraints in the center front seat WARNING: (Continued) position. When securing a child restraint in a rear seating position, study the instructions that came with your child Secure rear-facing child restraints in a rear restraint to make sure it is compatible with this vehicle. seat, even if the airbag is off.
Page 76 Lower Anchors and Tethers for Lower Anchors Children (LATCH) The LATCH system holds a child restraint during driving or in a crash. This system is designed to make installation of a child restraint easier. The LATCH system uses anchors in the vehicle and attachments on the child restraint that are made for use with the LATCH system.
Page 77: Top Tether Anchor
Top Tether Anchor Your child restraint may have a single tether (A) or a dual tether (C). Either will have a single attachment (B) to secure the top tether to the anchor. Some child restraints that have a top tether are designed for use with or without the top tether being attached.
Page 78 Lower Anchor and Top Tether Anchor (Top Tether Anchor): Seating positions with top Locations tether anchors. (Top Tether Anchor): (Lower Anchor): Seating positions with top Seating positions with two tether anchors. lower anchors. (Lower Anchor): Seating positions with two lower anchors. Extended Cab Rear Seat Crew Cab...
Page 79 For extended cab models with rear seats, there are (Top Tether Anchor): exposed metal lower anchors for each rear seating Seating positions with top position, attached to the back wall, near the seat tether anchors. cushion. To assist you in locating the lower anchors, place your hand in a palm-up position and reach up between the seat cushion and the seatback.
Page 80 Crew Cab Extended Cab Rear Seat The top tether anchors in a crew cab model are located The top tether anchors in an extended cab model are on the back wall behind each rear seating position. Be located on the center of the back wall behind a sure to use an anchor located on the same side of the removable cover for the rear seating positions.
Page 81 Do not secure a child restraint in a position without a top tether anchor if a national or local law requires that the top tether be attached, or if the instructions that come with the child restraint say that the top tether must be attached.
Page 82: Latch System
Securing a Child Restraint Designed for the WARNING: LATCH System WARNING: Do not attach more than one child restraint to a single anchor. Attaching more than one child restraint to a single anchor could cause the If a LATCH-type child restraint is not attached to anchor or attachment to come loose or even anchors, the child restraint will not be able to break during a crash.
Page 83 Crew Cab Rear Seat WARNING: Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten. Buckle any unused safety belts behind the child restraint so children cannot reach them. Pull the shoulder belt all the way out of the retractor to set the lock, if your vehicle has one, after the child restraint has been installed.
Page 84 2. 2. Route the top tether according to your child If the position you are restraint instructions and the following using has an adjustable instructions: headrest or head restraint and you are using a If the position you are single tether, raise the using has a fixed headrest or head restraint headrest or head restraint...
Page 85 3. Attach and tighten the lower attachments to the If the position you are lower anchors. If the child restraint does not have using has a fixed or lower attachments or the desired seating position adjustable headrest or does not have lower anchors, secure the child head restraint and you are restraint with the top tether and the safety belts.
Page 86 Extended Cab Rear Seat does not have lower anchors, secure the child restraint with the top tether and the safety belts. Refer to your child restraint manufacturer instructions and the instructions in this manual. 1. 1. Find the lower anchors (D) for the desired seating position.
Page 87 2. If the child restraint manufacturer recommends that Front Seat Regular/Extended Cab the top tether be attached, attach and tighten the without Rear Seats top tether to the top tether anchor (C). Refer to the The vehicle has a right front passenger airbag and may child restraint instructions and the following steps: also have a passenger sensing system.
Page 88 2. 3. Route the top tether according to your child If the position you are restraint instructions and the following using has a fixed or instructions: adjustable headrest or head restraint and you are If the position you are using a dual tether, route using has a fixed the tether around the headrest or head restraint...
Page 89: Securing A Child Restraint In A Rear
Securing a Child Restraint in a Rear In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be Seat Position attached. When securing a child restraint in a rear seating If your child restraint does not have the LATCH system, position, study the instructions that came with your child you will be using the safety belt to secure the child restraint to make sure it is compatible with this vehicle.
Page 90 3. Push the latch plate into the buckle until it clicks. 4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if 5.
Page 91 7. Tighten the top tether. See Lower Anchors and Tethers for Children (LATCH) on page 2 46. 8. Push and pull the child restraint in different directions to be sure it is secure. To remove the child restraint, unbuckle the vehicle s safety belt and let it go back all the way.
Page 92: Securing A Child Restraint In The Right Front
Securing a Child Restraint in the Passenger Airbag Status Indicator on page 4 23 for more information on this, including important safety Center Front Seat Position information. A label on the sun visor says, Never put a rear-facing WARNING: child seat in the front. This is because the risk to the rear-facing child is so great, if the airbag deploys.
Page 93 If your child restraint has the LATCH system, see Lower WARNING: (Continued) Anchors and Tethers for Children (LATCH) on page 2 46 for how and where to install your child restraint using LATCH. If a child restraint is secured Even if the passenger sensing system, using a safety belt and it uses a top tether, see Lower if equipped, has turned off the right front Anchors and Tethers for Children (LATCH) on...
Page 94 4. Push the latch plate into the buckle until it clicks. 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. Position the release button on the buckle so that the safety belt could be quickly unbuckled if 6.
Page 95 8. Tighten the top tether. See Lower Anchors and Tethers for Children (LATCH) on page 2 46. 9. Push and pull the child restraint in different directions to be sure it is secure. If the vehicle is equipped with the passenger sensing system, and when the passenger sensing system has turned off the right front passenger frontal airbag, the off indicator on the passenger airbag status indicator...
Page 96: Airbag System
Airbag System Here are the most important things to know about the airbag system: The vehicle has the following airbags: A frontal airbag for the driver. WARNING: A frontal airbag for the right front passenger Your vehicle may also have the following airbags: You can be severely injured or killed in a crash if you are not wearing your safety belt even if you...
Page 97 WARNING: WARNING: (Continued) Airbags inflate with great force, faster than the protection for adults and older children, but not for blink of an eye. Anyone who is up against, or young children and infants. Neither the vehicle's very close to, any airbag when it inflates can be safety belt system nor its airbag system is seriously injured or killed.
Page 98: Where Are The Airbags
Where Are the Airbags? The right front passenger's airbag is in the instrument panel on the passenger's side. The driver's airbag is in the middle of the steering wheel. 2-68 I n f o r ma t i o n P r o v i d e d b y :...
Page 99 WARNING: If something is between an occupant and an airbag, the airbag might not inflate properly or it might force the object into that person causing severe injury or even death. The path of an inflating airbag must be kept clear. Do not put anything between an occupant and an airbag, and do not attach or put anything on the steering wheel hub or on or near any other airbag...
Page 100: When Should An Airbag Inflate
If the vehicle hits a narrow object (like a pole), the When Should an Airbag Inflate? airbags could inflate at a different crash speed than if the vehicle hits a wide object (like a wall). Frontal airbags are designed to inflate in moderate to severe frontal or near-frontal crashes to help reduce the If the vehicle goes into an object at an angle, the potential for severe injuries mainly to the driver's or right...
Page 101: How Does An Airbag Restrain
Your vehicle may or may not have roof-rail airbags. See Frontal airbag modules are located inside the steering Airbag System on page 2 66. Roof-rail airbags are wheel and instrument panel. For vehicles with roof-rail intended to inflate in moderate to severe side crashes. airbags, there are airbag modules in the ceiling of the Roof-rail airbags will inflate if the crash severity is vehicle, near the side windows that have occupant...
Page 102: What Will You See After An Airbag
What Will You See After an Airbag WARNING: Inflates? After the frontal airbags inflate, they quickly deflate, so When an airbag inflates, there may be dust in the quickly that some people may not even realize the air. This dust could cause breathing problems for airbags inflated.
Page 103 In many crashes severe enough to inflate the airbag, WARNING: windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag. A crash severe enough to inflate the airbags may Airbags are designed to inflate only once. After an have also damaged important functions in the airbag inflates, you will need some new parts for vehicle, such as the fuel system, brake and...
Page 104: Passenger Sensing System
Passenger Sensing System The passenger sensing system will turn off the right front passenger frontal airbag under certain conditions. If the vehicle has one of the passenger airbag status The driver airbag is not affected by the passenger indicators pictured in the following illustrations, then the sensing system.
Page 105 If your vehicle does not have a rear seat that will WARNING: accommodate a rear-facing child restraint, a rear-facing child restraint should not be installed in the vehicle, even if the airbag is off. A child in a rear-facing child restraint can be The passenger sensing system is designed to turn off seriously injured or killed if the right front the right front passenger airbag if:...
Page 106 When the passenger sensing system has turned off the passenger's frontal airbag, depending upon the right front passenger frontal airbag, the off indicator will person's seating posture and body build. Everyone in light and stay lit to remind you that the airbag is off. See your vehicle who has outgrown child restraints should Passenger Airbag Status Indicator on page 4 23.
Page 107 If the On Indicator is Lit for a Child 5. If, after reinstalling the child restraint and restarting the vehicle, the on indicator is still lit, turn the Restraint vehicle off. Then slightly recline the vehicle seatback and adjust the seat cushion, if adjustable, If a child restraint has been installed and the on to make sure that the vehicle seatback is not indicator is lit:...
Page 108 If the Off Indicator is Lit for an Adult If this happens, use the following steps to allow the system to detect that person and enable the right front Size Occupant passenger frontal airbag: 1. Turn the vehicle off. 2. Remove any additional material from the seat, such as blankets, cushions, seat covers, seat heaters, or seat massagers.
Page 109 Additional Factors Affecting System A thick layer of additional material, such as a blanket or cushion, or aftermarket equipment such as seat Operation covers, seat heaters, and seat massagers can affect how well the passenger sensing system operates. Safety belts help keep the passenger in position on the We recommend that you not use seat covers or other seat during vehicle maneuvers and braking, which helps aftermarket equipment except when approved by GM...
Page 110: Adding Equipment To Your Airbag-Equipped
Servicing Your Airbag-Equipped Adding Equipment to Your Vehicle Airbag-Equipped Vehicle Airbags affect how the vehicle should be serviced. Q: Is there anything I might add to or change about There are parts of the airbag system in several places the vehicle that could keep the airbags from around the vehicle.
Page 111 may not operate properly if the original seat trim is Q: Because I have a disability, I have to get my replaced with non-GM covers, upholstery or trim, vehicle modified. How can I find out whether this or with GM covers, upholstery or trim designed for a will affect my airbag system? different vehicle.
Page 112: Restraint System Check
Airbags Restraint System Check The airbag system does not need regularly scheduled Checking the Restraint Systems maintenance or replacement. Make sure the airbag readiness light is working. See Airbag Readiness Light Safety Belts on page 4 22 for more information. Notice: If an airbag covering is damaged, opened, Now and then, check that the safety belt reminder light, or broken, the airbag may not work properly.
Page 113: Replacing Restraint System Parts After A Crash
Replacing Restraint System Parts If the vehicle has been in a crash, do you need new safety belts or LATCH system (if equipped) parts? After a Crash After a very minor crash, nothing may be necessary. But the safety belt assemblies that were used during WARNING: any crash may have been stressed or damaged.
Page 114 NOTES 2-84 I n f o r ma t i o n P r o v i d e d b y :...
Page 115: Features And Controls
Section 3 Features and Controls Theft-Deterrent Systems ......3-14 Keys ..........3-3 Remote Keyless Entry (RKE) System .
Page 116 Section 3 Features and Controls Shifting Out of Park (Automatic Outside Manual Mirrors ......3-42 Transmission) ....... 3-36 Outside Power Mirrors .
Page 117: Keys
Keys WARNING: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and children could be seriously injured or killed if caught in the path of a closing window.
Page 118 The key has a bar-coded key tag that the dealer/retailer If there is a decrease in the RKE operating range, or qualified locksmith can use to make new keys. Store try this: this information in a safe place, not in your vehicle. Check the distance.
Page 119: Remote Keyless Entry (Rke) System
Remote Keyless Entry (RKE) System LOCK: Press to lock all the doors. The parking lamps may flash and the horn may sound. Operation If a door is open or ajar when LOCK is pressed, the Vehicles with Remote Keyless Entry (RKE), transmitter horn sounds several times to let you know the doors did functions work up to 30 feet (9 m) away from the not lock and the content theft deterrent system is not...
Page 120: Programming Transmitters To The Vehicle
Programming Transmitters to the To replace the battery: Vehicle Only RKE transmitters programmed to the vehicle will work. If a transmitter is lost or stolen, a replacement can be purchased and programmed through your dealer/retailer. When the replacement transmitter is programmed to the vehicle, all remaining transmitters must also be programmed.
Page 121: Doors And Locks
Doors and Locks WARNING: (Continued) Door Locks Young children who get into unlocked vehicles may be unable to get out. A child can be WARNING: overcome by extreme heat and can suffer permanent injuries or even death from heat stroke. Always lock the vehicle whenever Unlocked doors can be dangerous.
Page 122: Power Door Locks
Power Door Locks Programmable Automatic Door Locks On vehicles with power door locks, the switches If the vehicle has power door locks and the remote are located on the driver keyless entry system, it has an automatic lock/unlock and the front passenger feature.
Page 123: Rear Door Security Locks (Crew Cab)
Rear Door Security Locks To open a rear door when the security lock is on, unlock the door and open the door from the outside. (Crew Cab) To disengage the security locks: If the vehicle is a crew cab model, it may have rear door 1.
Page 124: Tailgate
Tailgate WARNING: It is extremely dangerous to ride on the tailgate, even when the vehicle is operated at low speeds. People riding on the tailgate can easily lose their balance and fall in response to vehicle maneuvers. Falling from a moving vehicle may result in serious injuries or death.
Page 125: Removing The Tailgate
Removing the Tailgate To partially lower the tailgate: 1. With the tailgate fully open, lift up slightly on the To remove the tailgate: entire tailgate assembly. 1. With the tailgate fully open, lift up slightly on the 2. Remove the retaining entire tailgate assembly.
Page 126: Windows
Windows WARNING: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 127: Manual Windows
Manual Windows WARNING: (Continued) On vehicles with manual windows, use the window crank to open and close When there are children in the rear seat use the each window. window lockout button to prevent unintentional operation of the windows. Power Windows WARNING: Leaving children in a vehicle with the keys is dangerous for many reasons, children or others...
Page 128: Sun Visors
Express-Down Window Theft-Deterrent Systems Windows with an express-down feature allow the Vehicle theft is big business, especially in some cities. window to be lowered fully without pressing and holding This vehicle has theft-deterrent features, however, they the switch. Press the front of the switch to the first do not make it impossible to steal.
Page 129: Testing The Alarm
Testing the Alarm If a locked door is not opened using the RKE ® transmitter, or by OnStar , the pre-alarm will go off. To test the alarm: If the engine is not started or unlock not pressed within 10 seconds, the front turn signal lamps will flash for 1.
Page 130: Passlock ® (U. S. Only)
® ® Passlock (U. S. Only) PASS-Key III+ Electronic Immobilizer ® Passlock is a passive theft-deterrent system that enables fuel if the vehicle is started with a valid key. See Radio Frequency Statement on page 8 20 for If an incorrect key is used or the ignition lock cylinder is information regarding Part 15 of the Federal tampered with, the fuel system is disabled and the Communications Commission (FCC) Rules and...
Page 131 If the engine still does not start, and the key appears to 4. Insert the second current driver's key in the be undamaged, try another ignition key. Check the fuse. ignition and start the engine within ten seconds of See Fuses and Circuit Breakers on page 6 112. If the removing the previous key.
Page 132: Starting And Operating Your Vehicle
Avoid making hard stops for the first Starting and Operating Your 200 miles (322 km) or so. During this time the Vehicle new brake linings are not yet broken in. Hard stops with new linings can mean premature wear and earlier replacement. Follow this New Vehicle Break-In breaking-in guideline every time you get new Notice: The vehicle does not need an elaborate...
Page 133: Ignition Positions
Ignition Positions (A) LOCK/OFF: This position locks the ignition. It also locks the transmission on automatic transmission The ignition switch has vehicles. It locks the steering wheel on manual four different positions. transmission vehicles. The key can on be removed in LOCK/OFF.
Page 134: Retained Accessory Power (Rap)
Starting the Engine If you leave the key in the ACC/ACCESSORY or ON/RUN position with the engine off, the battery could Place the transmission in the proper gear. be drained. You may not be able to start your vehicle if the battery is allowed to drain for an extended period Automatic Transmission of time.
Page 135: Starting Procedure
Starting Procedure 2. If the engine does not start after 5 10 seconds, especially in very cold weather (below 0°F or 1. With your foot off the accelerator pedal, turn the 18°C), it could be flooded with too much gasoline. ignition key to START.
Page 136: Engine Coolant Heater
Engine Coolant Heater WARNING: The engine coolant heater can provide easier starting and better fuel economy during engine warm-up in cold weather conditions at or below 0°F ( 18°C). Vehicles Plugging the cord into an ungrounded outlet could with an engine coolant heater should be plugged in at cause an electrical shock.
Page 137: Automatic Transmission Operation
Automatic Transmission Operation P (Park): This position locks the rear wheels. It is the best position to use when you start the engine because the vehicle cannot move easily. WARNING: It is dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set.
Page 138 If you cannot shift out of P (Park), ease pressure on the shift lever by pushing the shift lever all the way into WARNING: P (Park) as you maintain brake application. Then move the shift lever into another gear. See Shifting Out of Shifting into a drive gear while the engine is Park (Automatic Transmission) on page 3 36.
Page 139 D (Drive): This position is for normal driving. It provides 2 (Second): This position reduces vehicle speed even the best fuel economy. If you need more power for more than 3 (Third) without using the brakes. You can passing, and you are: use 2 (Second) to help control vehicle speed on steep mountain roads, but then you would also want to use Going less than about 35 mph (55 km/h), push the...
Page 140: Manual Transmission Operation
Manual Transmission Operation 3 (Third), 4 (Fourth) and 5 (Fifth): Shift into 3 (Third), 4 (Fourth) and 5 (Fifth) the same way you do for This is your shift pattern. 2 (Second). Slowly let up on the clutch pedal as you press the accelerator pedal.
Page 141: Shift Speeds
Up-Shift Light While you accelerate, it is normal for the light to go on and off if you quickly change the position of the This light will show you accelerator. Ignore the shift light when you downshift. when to shift to the next If the vehicle has four-wheel drive and has a manual higher gear for best fuel transmission, disregard the shift light when the transfer...
Page 142: Four-Wheel Drive
Four-Wheel Drive If the vehicle has four-wheel drive, you can send the engine's driving power to all four wheels for extra traction. To get the best performance out of four-wheel drive, you must be familiar with its operation. Read this section before using four-wheel drive.
Page 143 Shifting into Four Wheel Low will turn Traction Control N (Neutral): Shift the vehicle's transfer case to ® and StabiliTrak off. See Traction Control System (TCS) N (Neutral) only when towing the vehicle. ® on page 5 8 and StabiliTrak System on page 5 6 4 (Four-Wheel High): This setting engages the front for more information.
Page 144 Shifting from Two-Wheel High to Shifting from Two-Wheel High or Four-Wheel High Four-Wheel High to Four-Wheel Low Press and release the Four-Wheel High button. This To shift from Two-Wheel High or Four-Wheel High to can be done at any speed, and the front axle will lock Four-Wheel Low, the vehicle must be stopped or automatically.
Page 145: Shifting To Neutral
Shifting from Four-Wheel Low to Shifting to Neutral Two-Wheel High or Four-Wheel High Use N (Neutral) when you plan to tow the vehicle. See Recreational Vehicle Towing on page 5 39 for towing To shift from Four-Wheel Low to Two-Wheel High or instructions.
Page 146 6. Press and hold the regular brake pedal and shift Shifting Out of Neutral the transmission to R (Reverse) for one second, After towing the vehicle, you will have to shift out of then shift the transmission to D (Drive) for N (Neutral) in order to drive.
Page 147: Parking Brake
Parking Brake The parking brake pedal is located to the left of the brake pedal, near the driver door. To set the parking brake, hold the brake pedal down, then push the parking brake pedal down to its To release the parking brake, hold the regular brake fully-applied position.
Page 148: Shifting Into Park (Automatic Transmission)
Shifting Into Park (Automatic WARNING: Transmission) If you have four-wheel drive, the vehicle will WARNING: be free to roll even if the shift lever is in P (Park) if the transfer case is in Neutral. So, be sure the transfer case is in a drive gear, It can be dangerous to get out of the vehicle if the two-wheel high (2H) or four-wheel high (4H) or shift lever is not fully in P (Park) with the parking...
Page 149 Leaving the Vehicle With the Engine Torque Lock (Automatic Transmission) Running (Automatic Transmission) If you are parking on a hill and you do not shift the transmission into P (Park) properly, the weight of the vehicle may put too much force on the parking pawl in WARNING: the transmission.
Page 150: Shifting Out Of Park
Shifting Out of Park (Automatic To shift out of P (Park) use the following: 1. Apply the brake pedal. Transmission) 2. Move the shift lever to the desired position. The vehicle has an automatic transmission shift lock If you still are unable to shift out of P (Park): control system.
Page 151: Parking Over Things That Burn
Parking Over Things That Burn WARNING: (Continued) WARNING: The exhaust system leaks due to corrosion or damage. Things that can burn could touch hot exhaust The vehicle s exhaust system has been parts under the vehicle and ignite. Do not park modified, damaged or improperly repaired.
Page 152: Running The Vehicle While Parked
Running the Vehicle While Parked WARNING: (Continued) It is better not to park with the engine running. But if you ever have to, here are some things to know. left the engine running, the vehicle can move suddenly. You or others could be injured. To be WARNING: sure the vehicle will not move, even when it is on fairly level ground, always set the parking brake...
Page 153: Mirrors
Automatic Dimming Rearview Mirror Mirrors The vehicle may have an automatic dimming inside Manual Rearview Mirror rearview mirror. Automatic dimming reduces the glare of lights from behind the vehicle. Hold the inside rearview mirror in the center to move it ®...
Page 154: Compass
Temperature Display Compass (On/Off) : Press or depending on the Compass Operation mirror, press to turn the display on or off. Press or depending on the mirror, press once to To adjust between Fahrenheit and Celsius: turn the display on or off. 1.
Page 155: Compass Variance
To calibrate, CAL must be displayed in the mirror To adjust for compass variance: compass windows. If CAL is not displayed, press and 1. Find the current location and variance zone hold for several seconds or until CAL is number on the following zone map. displayed.
Page 156: Outside Manual Mirrors
Outside Manual Mirrors To adjust the power mirrors: 1. Move the selector switch to the L (left) or R (right) Manually fold the mirrors inward to prevent damage when going through an automatic car wash. To fold, to choose the driver or passenger mirror. push the mirrors toward the vehicle.
Page 157: Outside Convex Mirror
Outside Convex Mirror Storage Areas Glove Box WARNING: Lift up on the glove box lever to open it. A convex mirror can make things, like other Cupholders vehicles, look farther away than they really are. If you cut too sharply into the right lane, you could This vehicle may have two cupholders located on the hit a vehicle on the right.
Page 158: Center Console Storage
Center Console Storage Rear Storage Area For vehicles with bench seats, there may be a center Extended cab models might have storage armrest storage area. Lift up on the upper tab located at compartments under the rear seats. the front of the armrest to release the latch. Lift the lid to open the storage area.
Page 159 Lift the lid from the center area to access the storage box. To open a storage box, unhook the bottom and lift the two latches on each side of the storage box. I n f o r ma t i o n P r o v i d e d b y : 3-45...
Page 160: Sunroof
Sunroof (Open/Vent): Press and hold this button to vent, and open the sunroof. Release the button when the desired The vehicle may have a sunroof. position is reached. (Close): Press and hold this button to close the The sunroof control sunroof.
Page 161: Instrument Panel
Section 4 Instrument Panel Climate Controls ........4-16 Instrument Panel Overview .
Page 162 Section 4 Instrument Panel Driver Information Center (DIC) ....4-33 XM Radio Messages ......4-59 DIC Operation and Displays .
Page 163: Instrument Panel Overview
Tilt Wheel Instrument Panel Overview Hazard Warning Flashers (Hazard Warning Flasher): Press this button located on the instrument panel, to make the front and rear turn signal lamps flash on and off. This warns others that you are having trouble. Press again to turn the flashers off.
Page 164: Turn Signal/Multifunction Lever
Turn Signal/Multifunction Lever Turn and Lane-Change Signals An arrow on the instrument panel cluster flashes in the direction of the turn or lane change. Move the lever all the way up or down to signal a turn. Raise or lower the lever until the arrow starts to flash to signal a lane change.
Page 165: Headlamp High/Low-Beam Changer
Flash-to-Pass Turn Signal On Chime If a turn signal is left on for more than 3/4 of a mile This feature lets you use the high-beam headlamps to (1.2 km), a chime will sound at each flash of the turn signal a driver in front of you that you want to pass.
Page 166: Windshield Washer
Windshield Washer Move the band to one of the following positions: 8 (Mist): Single wipe, move the band to and then WARNING: release it. Several wipes, hold the band on longer. N (Adjustable Interval Wipes): For a delayed wiping cycle. Turn the band up for more frequent wipes or In freezing weather, do not use your washer until down for less frequent wipes.
Page 167: Cruise Control
Cruise Control System (TCS) on page 5 8. When road conditions allow you to safely use it again, the cruise control can With cruise control, a speed of about 40 km/h (25 mph) be turned back on. or more can be maintained without keeping your foot on the accelerator.
Page 168 Setting Cruise Control WARNING: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be This light on the instrument panel cluster comes on startled and even lose control.
Page 169 Increasing Speed While Using Cruise Passing Another Vehicle While Using Control Cruise Control There are two ways to go to a higher speed: Use the accelerator pedal to increase the vehicle speed. When you take your foot off the pedal, the Use the accelerator pedal to get to the higher vehicle slows down to the cruise control speed you set speed.
Page 170: Exterior Lamps
Exterior Lamps AUTO: Turns the headlamps on automatically at normal brightness, together with the following: Sidemarker Lamps Taillamps Parking Lamps Instrument Panel Lights See Automatic Headlamp System on page 4 12 for more information. ; (Parking Lamps): Turns on the parking lamps, together with the following: Sidemarker Lamps Taillamps...
Page 171: Headlamps On Reminder
Headlamps on Reminder The DRL system will come on when the following conditions are met: If a door is open, a reminder chime sounds when the The ignition is on. headlamps or parking lamps are manually turned on The exterior lamps control is in AUTO. and the key is out of the ignition.
Page 172: Automatic Headlamp System
Automatic Headlamp System If the vehicle is started in a dark garage, the automatic headlamp system will come on immediately. Once the When it is dark enough outside, the automatic vehicle leaves the garage, it will take about one minute headlamp system will turn on after the transmission has for the automatic headlamp system to change to DRL if been shifted from P (Park) to D (Drive).
Page 173: Exterior Cargo Lamps
Exterior Cargo Lamps Instrument Panel Brightness The cargo lamps can be used if more light is needed in (Instrument Panel Lights): Turn the thumbwheel up the cargo area of the vehicle or in the top-box storage or down to brighten or dim the instrument panel lights units.
Page 174: Dome Lamp Override
Dome Lamp Override The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is The dome lamp override button is located below the because the generator (alternator) may not be spinning exterior lamps control.
Page 175: Battery Run-Down Protection
Battery Run-Down Protection Certain electrical accessories may not be compatible with the accessory power outlet and could result in This feature shuts off the dome lamp if it is left on for blown vehicle or adapter fuses. If you experience a more than 20 minutes when the ignition is in LOCK/OFF.
Page 176: Ashtray(S) And Cigarette Lighter
Ashtray(s) and Cigarette Lighter Climate Controls The vehicle may have a removable ashtray and Climate Control System cigarette lighter. The ashtray is located in the center console area. The The heating, cooling, and ventilation for the vehicle can ashtray can be removed for cleaning. When the ashtray be controlled with this system.
Page 177 9 (Fan Control): Turn the knob clockwise or system runs the air conditioning compressor unless counterclockwise to increase or decrease the fan the outside temperature is near, or below freezing. speed. Recirculation is not available in this mode. If the knob is set on 0 (zero), some outside air will still Do not drive the vehicle until all the windows are clear.
Page 178: Outlet Adjustment
Outlet Adjustment Warning Lights, Gauges, and Indicators Use the thumbwheel on the outlets to change the direction of the air flow. Warning lights and gauges can signal that something is Lift up or push down on the thumbwheel located in the wrong before it becomes serious enough to cause an center of the outlet to direct the air up or down, or slide expensive repair or replacement.
Page 179 United States automatic transmission 2.9L version shown, Canada, manual transmission, 3.7L and 5.3L similar I n f o r ma t i o n P r o v i d e d b y : 4-19...
Page 180: Speedometer And Odometer
Speedometer and Odometer Trip Odometer The speedometer shows the speed in both miles per The vehicle has a trip odometer that indicates how far hour (mph) and kilometers per hour (km/h). the vehicle has been driven since the trip odometer was last set to zero.
Page 181: Safety Belt Reminders
Safety Belt Reminders Passenger Safety Belt Reminder Light For vehicles equipped with the passenger safety belt Driver Safety Belt Reminder Light reminder light, several seconds after the engine is When the engine is started, a chime sounds for several started, a chime sounds for several seconds to remind seconds to remind a driver to fasten the safety belt, the front passenger to buckle their safety belt.
Page 182: Airbag Readiness Light
Airbag Readiness Light WARNING: The system checks the airbag's electrical system for possible malfunctions. If the light stays on it indicates there is an electrical problem. The system check If the airbag readiness light stays on after the includes the airbag sensor, the pretensioners, the vehicle is started or comes on while driving, it airbag modules, the wiring and the crash sensing and means the airbag system might not be working...
Page 183: Passenger Airbag Status Indicator
Passenger Airbag Status Indicator will light either ON or OFF, or either the on or off symbol to let you know the status of the right front passenger If the vehicle has one of the passenger airbag status frontal airbag. indicators pictured in the following illustrations, then the If the word ON or the on symbol is lit on the passenger vehicle has a passenger sensing system for the right...
Page 184: Charging System Light
Charging System Light Up-Shift Light This light comes on briefly The vehicle may have an when the ignition key is up-shift light. turned to START, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer/ When this light comes on, shift to the next higher gear if retailer.
Page 185: Antilock Brake System (Abs) Warning Light
WARNING: The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has United States Canada been pulled off the road and carefully stopped,...
Page 186 If the ABS light stays on, turn the ignition off. If the light If it does not, have the vehicle serviced by your dealer/ comes on while driving, stop as soon as it is safely retailer. If the system is working normally the indicator possible and turn the ignition off.
Page 187: Engine Coolant Temperature Gauge
Engine Coolant Temperature Gauge Tire Pressure Light This gauge shows the For vehicles with a tire engine coolant pressure monitoring temperature. system, this light comes on briefly when the engine is started. It provides information about tire pressures and the Tire Pressure Monitoring System.
Page 188: Malfunction Indicator Lamp
When the Light Flashes First and Then is If the check engine light comes on and stays on, while On Steady the engine is running, this indicates that there is an OBD II problem and service is required. This indicates that there may be a problem with the Tire Pressure Monitor System.
Page 189 This light comes on during a malfunction in one of An emission system malfunction might be corrected by two ways: doing the following: Make sure the fuel cap is fully installed. See Filling Light Flashing: A misfire condition has been detected. the Tank on page 6 8.
Page 190: Maintenance Schedule
If none of the above have made the light turn off, your vehicle still does not pass the inspection for lack of dealer/retailer can check the vehicle. The dealer/retailer OBD II system readiness, your dealer/retailer can has the proper test equipment and diagnostic tools to fix prepare the vehicle for inspection.
Page 191: Security Light
Cruise Control Light This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer/ The cruise control light retailer. If the system is working normally the indicator light then goes off. comes on whenever the cruise control is set.
Page 192: Fuel Gauge
Fuel Gauge Here are four things that some owners ask about. None of these indicate a problem with the vehicle's fuel When the ignition is on, gauge: the fuel gauge shows how At the gas station, the gas pump shuts off before much fuel the vehicle has the gauge reads full.
Page 193: Driver Information Center (Dic)
Trip Information Driver Information Center (DIC) Odometer The Driver Information Center (DIC) displays information such as the trip odometer, personalization The odometer is automatically displayed on the DIC features, and warning messages. The DIC display is when you start the vehicle. The odometer shows the located on the instrument panel cluster.
Page 194: Automatic Door Locks
In addition to the engine oil life system monitoring the Automatic Door Locks oil life, additional maintenance is recommended in the This feature allows you to program the door locks to a Maintenance Schedule in this manual. See Engine Oil preferred setting.
Page 195 Lock 2: On vehicles with an automatic transmission, Remote Keyless Entry (RKE) Feedback this mode locks all of the doors when the vehicle is This feature allows you to program the Remote Keyless shifted out of P (Park) and unlocks the driver's door Entry (RKE) feedback to a preferred setting.
Page 196: Dic Warnings And Messages
DIC Warnings and Messages The following are the available modes: RFA 1 (default): This mode flashes the parking lamps Messages are displayed on the DIC to notify the driver when you press the lock or unlock buttons on the RKE that the status of the vehicle has changed and that transmitter.
Page 197 AC (Air Conditioning) OFF CHANGE OIL This message displays when the engine coolant This message displays when the oil needs to be temperature is too high and the air conditioning in changed. Check the oil in your vehicle as soon as your vehicle needs to be turned off.
Page 198: Fuel Cap
FLUID LOW TIRE This message displays if the brake fluid is low. Check This message displays if a low tire pressure is detected the brake fluid as soon as possible and have your in any of the vehicle's tires. Press and release the reset vehicle serviced by your dealer/retailer.
Page 199: Tire Pressure Monitor
REDUCED POWER SERV (Service) TPM (Tire Pressure Monitor) This message displays when the vehicle's engine power is reduced. Reduced engine power can affect the This message displays if a part on the Tire Pressure vehicle's ability to accelerate. If this message is on, but Monitor System (TPMS) is not working properly.
Page 200 SERVICE CHARG (Charge) SYS TRAC (Traction) OFF (System) This message displays when the Traction Control System (TCS) is turned off by pressing the StabiliTrak This message displays if there is a problem with the ® button. See StabiliTrak System on page 5 6 for more battery charging system.
Page 201: Audio System(S)
Audio System(s) Notice: Contact your dealer/retailer before adding any equipment. Determine which radio the vehicle has and read the Adding audio or communication equipment could following pages to become familiar with its features. interfere with the operation of the vehicle's engine, radio, or other systems, and could damage them.
Page 202: Setting The Clock
Setting the Clock Radio(s) AM-FM Radio Press and hold HR until the correct hour displays. Press and hold MIN until the correct minute displays. There is an initial two-second delay before the clock goes into time-set mode. To display the time with the ignition off, press RCL, HR, or MIN.
Page 203 Radio Data System (RDS) The audio system has a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information. With RDS, the radio can do the following: Seek to stations broadcasting the selected type of programming.
Page 204: Playing The Radio
Playing the Radio To change the default on the display, press the DISPL knob until you see the desired display, then press and PWR (Power): Press to turn the system on and off. hold this knob for two seconds. The radio produces one beep.
Page 205: Finding A Station
Finding a Station SCAN : Press and hold for more than two seconds. SCAN or SCN displays and the radio AM FM (AM-FM Radio): Press to switch between FM1, produces one beep. The radio goes to a station, plays FM2, or AM. The selection displays. for a few seconds, then goes to the next station.
Page 206: Setting Preset Stations
Setting Preset Stations Setting the Tone (Bass/Treble) If the radio does not have XM, up to 18 stations AUDIO: Push and release until BASS/TREB, (six FM1, six FM2, and six AM) can be programmed on or depending on the radio, BASS, MID, or TREB the six numbered pushbuttons.
Page 207 Adjusting the Speakers (Balance/Fade) To adjust all tone and speaker controls to the middle position, push and hold the AUDIO knob when no tone AUDIO: To adjust the balance between the right and or speaker control displays. ALL CENTERED displays the left speakers, push and release until BAL (balance) and a beep sounds.
Page 208: Rds And Xm
Finding a Program Type (PTY) Station To adjust the balance or the fade to the middle position, push the AUDIO knob to select BAL or FADE/FAD, then (RDS and XM) push it again and hold it until one beep sounds. To select and find a desired PTY perform the following: For the AM-FM Radio, adjust balance or fade to the middle position by selecting BAL or FAD.
Page 209 Setting Preset PTYs (RDS) Only If both PTY and TRAF (traffic) are on, the radio searches for stations with the selected PTY and traffic For the Radio with CD player, the six pushbuttons announcements. have factory PTY presets. Up to 12 PTYs (six FM1 and If the radio cannot find the desired program type, NONE six FM2), can be programmed on the numbered displays and the radio returns to the last tuned station.
Page 210: Rds Messages
RDS Messages The last message can be displayed by pressing the INFO button. The last message stays on the display ALERT!: For the Radio with CD, the Alert feature until a new message is received or the radio is tuned to warns of local or national emergencies.
Page 211: Radio Messages
Radio Messages Radio Messages for XM Only See XM Radio Messages on page 4 59 later in this CAL ERR or CAL (Calibration Error): The audio section for further detail. system has been calibrated for the vehicle from the factory. If CAL or CAL ERR displays it means that the Playing a CD (Radio with Single CD radio has not been configured properly for the vehicle Player)
Page 212: Care Of Your Cds
Care of Your CDs Care of Your CD Player If playing a CD-R, the sound quality can be reduced Do not add any label to a CD, it could get caught in the due to CD-R quality, the method of recording, the CD player.
Page 213 3 REV (Fast Reverse): Press and hold to reverse TUNE : Turning this knob fast tracks reverse or quickly within a track. Press and hold for less than advances through tracks. The track number displays for two seconds to reverse at 10 times the normal playing each track.
Page 214 The air is very humid. If so, wait about an hour and Playing an MP3/WMA CD-R Disc try again. Radios with the MP3/WMA feature are capable of The format of the CD might not be compatible. See playing an MP3/WMA CD-R disc. For more information Using an MP3 on page 4 55 later in this section.
Page 215: Using An Mp3
Using an MP3 The player is able to read and play a maximum of 253 folders, 50 playlists, 20 sessions, and 949 files. MP3/WMA CD-R Disc Long file names, folder names, or playlist names may use more disc memory space than necessary. MP3/WMA Format To conserve space on the disc, minimize the length of the file, folder, or playlist names.
Page 216 Empty Directory or Folder Order of Play If a root directory or a folder exists somewhere in the Tracks are played in the following order: file structure that contains only folders/subfolders and Play begins from the first track in the first playlist no compressed files directly beneath them, the player and continues sequentially through all tracks in advances to the next folder in the file structure that...
Page 217 File System and Naming As each new track starts to play, the track number displays. The song name that displays is the song name that is contained in the ID3 tag. If the song name is not 1 FLD (Previous Folder): Press this button to go to present in the ID3 tag, then the radio displays the file the first track in the previous folder.
Page 218 6 RDM (Random): To play the tracks in random order DISPL (Display): Press this knob to switch between in the current folder or playlist, press and release this track mode, folder/playlist mode, and time of day mode. button. FLDR RDM (folder random) displays. Once all of The display shows only eight characters, but there can the tracks in the current folder or playlist have played, be up to four pages of text.
Page 219: Xm Radio Messages
CD AUX (Auxiliary): Press this button to play a CD CH Unavl: This previously assigned channel is no when listening to the radio. The CD symbol illuminates longer assigned. Tune to another station. If this station on the display when a CD is loaded. was one of the presets, choose another station for that preset button.
Page 220: Theft-Deterrent Feature
Theft-Deterrent Feature Radio Reception Frequency interference and static can occur during Non-RDS Radios normal radio reception if items such as cell phone ® THEFTLOCK is designed to discourage theft of your chargers, vehicle convenience accessories, and vehicle's radio. The feature works automatically by external electronic devices are plugged into the learning a portion of the Vehicle Identification Number accessory power outlet.
Page 221: Fixed Mast Antenna
Satellite Radio Service Satellite Radio Antenna System XM Satellite Radio Service gives digital radio reception from coast-to-coast in the 48 contiguous United States, The XM Satellite Radio antenna is located on the roof of and in Canada. Just as with FM, tall buildings or hills the vehicle.
Page 222 NOTES 4-62 I n f o r ma t i o n P r o v i d e d b y :...
Page 223: Driving Your Vehicle
Section 5 Driving Your Vehicle Your Driving, the Road, and the Vehicle ..5-2 Before Leaving on a Long Trip ....5-25 Defensive Driving .
Page 224: Your Driving, The Road, And The Vehicle
Drunk Driving Your Driving, the Road, and the Vehicle WARNING: Defensive Driving Drinking and then driving is very dangerous. Defensive driving means always expect the Your reflexes, perceptions, attentiveness, and unexpected. The first step in driving defensively is to judgment can be affected by even a small amount wear your safety belt See Safety Belts: They Are for Everyone on page 2 14.
Page 225: Control Of A Vehicle
Braking For persons under 21, it is against the law in every U.S. state to drink alcohol. There are good medical, See Brake System Warning Light on page 4 24. psychological, and developmental reasons for these laws. Braking action involves perception time and reaction time.
Page 226: Antilock Brake System (Abs)
Antilock Brake System (ABS) Avoid needless heavy braking. Some people drive in spurts, heavy acceleration followed by heavy braking, This vehicle has the Antilock Brake System (ABS), an rather than keeping pace with traffic. This is a mistake. advanced electronic braking system that helps prevent The brakes might not have time to cool between hard a braking skid.
Page 227: Braking In Emergencies
Braking in Emergencies Let us say the road is wet and you are driving safely. Suddenly, an animal jumps out in front of you. You slam ABS allows the driver to steer and brake at the same on the brakes and continue braking. Here is what time.
Page 228: Stabilitrak ® System
® StabiliTrak System If there is a problem detected with StabiliTrak, a SERVICE STAB SYS message displays on the Driver The vehicle has an electronic stability control system Information Center (DIC). See DIC Warnings and called StabiliTrak. It is an advanced computer controlled Messages on page 4 36 for more information.
Page 229 To turn off TCS and StabiliTrak, press and hold The StabiliTrak/TCS the StabiliTrak/TCS button until the TRAC OFF and light will flash on the STAB SYS OFF messages come on the DIC and the instrument panel cluster StabiliTrak/TCS light comes on the instrument panel. when the TCS system or To turn TCS and StabiliTrak back on, press and release StabiliTrak is both on and...
Page 230: Traction Control System (Tcs)
Traction Control System (TCS) TCS can operate on dry roads under some conditions. When this happens, the system may be heard working The Traction Control System (TCS) is part of or a reduction in acceleration may be noticed. This is StabiliTrak.
Page 231: Limited-Slip Rear Axle
Limited-Slip Rear Axle The StabiliTrak/TCS light will flash on the Vehicles with a limited-slip rear axle can give more instrument panel cluster traction on snow, mud, ice, sand or gravel. It works like when the TCS system or a standard axle most of the time, but when traction is StabiliTrak is both on and low, this feature allows the drive wheel with the most activated.
Page 232: Steering In Emergencies
Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and find a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Page 233: Off-Road Recovery
Off-Road Recovery Passing The vehicle's right wheels can drop off the edge of a Passing another vehicle on a two-lane road can be road onto the shoulder while driving. dangerous. To reduce the risk of danger while passing: Look down the road, to the sides, and to crossroads for situations that might affect a successful pass.
Page 234 Skidding If the vehicle starts to slide, ease your foot off the accelerator pedal and quickly steer the way you want In a skid, a driver can lose control of the vehicle. the vehicle to go. If you start steering quickly enough, Defensive drivers avoid most skids by taking the vehicle may straighten out.
Page 235: Off-Road Driving
Off-Road Driving Before You Go Off-Roading Have all necessary maintenance and service Vehicles with four-wheel drive can be used for off-road work done. driving. Vehicles without four-wheel drive should not be driven off-road except on a level, solid surface. Make sure there is enough fuel, that fluid levels are where they should be, and that the spare tire is The airbag system is designed to work properly under a fully inflated.
Page 236 Loading Your Vehicle for Off-Road WARNING: (Continued) Driving Heavy loads on the roof raise the vehicle's WARNING: center of gravity, making it more likely to roll over. You can be seriously or fatally injured if the vehicle rolls over. Put heavy loads inside Cargo on the load floor piled higher than the the cargo area, not on the roof.
Page 237: Environmental Concerns
Environmental Concerns Traveling to Remote Areas Off-road driving can provide wholesome and satisfying It makes sense to plan your trip, especially when going recreation. However, it also raises environmental to a remote area. Know the terrain and plan your route. concerns.
Page 238: Scanning The Terrain
Scanning the Terrain Controlling the vehicle is the key to successful off-road driving. One of the best ways to control the vehicle is to Off-road driving can take you over many different kinds control the speed. At higher speeds: of terrain. Be familiar with the terrain and its many You approach things faster and have less time to different features.
Page 239: Approaching A Hill
Approaching a Hill When driving over bumps, rocks, or other obstacles, the wheels can leave the ground. If this happens, even with When you approach a hill, decide if it is too steep to one or two wheels, you cannot control the vehicle as climb, descend, or cross.
Page 240: Driving Uphill
Attach a flag to the vehicle to be more visible to Driving Uphill approaching traffic on trails or hills. Once you decide it is safe to drive up the hill: Sound the horn as you approach the top of the hill Use a low gear and get a firm grip on the steering to let opposing traffic know you are there.
Page 241 If the engine has stopped running, you need If, after stalling, you try to back down the hill and decide to restart it. With the brake pedal pressed you just cannot do it, set the parking brake, shift to and the parking brake still applied, shift the P (Park) or 1 (First) with a manual transmission, and automatic transmission to P (Park) or the manual turn off the engine.
Page 242: Driving Downhill
Driving Downhill Things not to do when driving down a hill: When driving downhill, avoid turns that take you When off-roading takes you downhill, consider: across the incline of the hill. A hill that is not too How steep is the downhill? Will I be able to steep to drive down might be too steep to drive maintain vehicle control? across.
Page 243: Driving Across An Incline
Surface conditions can be a problem. Loose Driving Across an Incline gravel, muddy spots, or even wet grass can An off-road trail will probably go across the incline of a cause the tires to slip sideways, downhill. If the hill. To decide whether to try to drive across the incline, vehicle slips sideways, it can hit something that consider the following: will trip it...
Page 244: Stalling On An Incline
Stalling on an Incline When driving on sand, wheel traction changes. On loosely packed sand, such as on beaches or sand dunes, the tires will tend to sink into the sand. This WARNING: affects steering, accelerating, and braking. Drive at a reduced speed and avoid sharp turns or abrupt maneuvers.
Page 245: Driving In Water
Driving in Water After Off-Road Driving Remove any brush or debris that has collected on the underbody, chassis, or under the hood. These WARNING: accumulations can be a fire hazard. After operation in mud or sand, have the brake linings Driving through rushing water can be dangerous.
Page 246: Driving At Night
Driving at Night Driving in Rain and on Wet Roads Night driving is more dangerous than day driving Rain and wet roads can reduce vehicle traction and because some drivers are likely to be impaired affect your ability to stop and accelerate. Always drive alcohol or drugs, with night vision problems, or by slower in these types of driving conditions and avoid fatigue.
Page 247: Other Rainy Weather Tips
Hydroplaning Things to check on your own include: Windshield Washer Fluid: Reservoir full? Windows Hydroplaning is dangerous. Water can build up under clean inside and outside? your vehicle's tires so they actually ride on the water. This can happen if the road is wet enough and you are Wiper Blades: In good shape? going fast enough.
Page 248: Hill And Mountain Roads
Hill and Mountain Roads WARNING: Driving on steep hills or through mountains is different than driving on flat or rolling terrain. Tips for driving in these conditions include: Coasting downhill in N (Neutral) or with the ignition off is dangerous. The brakes will have to Keep the vehicle serviced and in good shape.
Page 249: Winter Driving
® Winter Driving The StabiliTrak System on page 5 6 improves the ability to accelerate on slippery roads, but slow down Driving on Snow or Ice and adjust your driving to the road conditions. When driving through deep snow, it might be beneficial to turn Drive carefully when there is snow or ice between the ®...
Page 250 Blizzard Conditions WARNING: (Continued) Being stuck in snow can be in a serious situation. Stay with the vehicle unless there is help nearby. If possible, use the Roadside Assistance Program on page 8 8. Open a window about 5 cm (two inches) on To get help and keep everyone in the vehicle safe: the side of the vehicle that is away from the wind to bring in fresh air.
Page 251: If Your Vehicle Is Stuck In Sand, Mud, Ice
If Your Vehicle is Stuck in Sand, Run the engine for short periods only as needed to keep warm, but be careful. Mud, Ice, or Snow To save fuel, run the engine for only short periods as Slowly and cautiously spin the wheels to free the needed to warm the vehicle and then shut the engine vehicle when stuck in sand, mud, ice, or snow.
Page 252: Rocking Your Vehicle To Get It Out
Rocking Your Vehicle to Get It Out Recovery Hooks Turn the steering wheel left and right to clear the area around the front wheels. For four-wheel drive vehicles, WARNING: shift into 4HI. Turn off any traction system. Shift back and forth between R (Reverse) and a forward gear, or with a manual transmission, between 1 (First) or These hooks, when used, are under a lot of force.
Page 253: Loading The Vehicle
Loading the Vehicle It is very important to know how much weight your vehicle can carry. This weight is called the vehicle capacity weight and includes the weight of all occupants, cargo, and all nonfactory-installed options. Two labels on your vehicle show how much weight it may properly carry, the Tire and Loading Information label and the Certification/Tire label.
Page 254 Tire and Loading Information Label Vehicle's without a center pillar, like extended cab models, will have the Tire and Loading Information label attached to the driver side extended cab door, above the door latch post. The Tire and Loading Information label shows the number of occupant seating positions (A), and the maximum vehicle capacity weight (B) in kilograms and pounds.
Page 255 Steps for Determining Correct Load Limit Determine the combined weight of luggage and cargo being loaded on the vehicle. That Locate the statement The combined weight weight may not safely exceed the available of occupants and cargo should never exceed cargo and luggage load capacity calculated in XXX kg or XXX lbs on your vehicle's placard.
Page 256 Example 1 Example 2 Item Description Total Item Description Total Vehicle Capacity Vehicle Capacity 1,000 lbs 1,000 lbs Weight for Weight for (453 kg) (453 kg) Example 1 = Example 2 = Subtract Occupant Subtract Occupant Weight @ 150 lbs 300 lbs (136 kg) Weight @ 150 lbs 750 lbs (340 kg)
Page 257 Refer to your vehicle's Tire and Loading Information label for specific information about your vehicle's capacity weight and seating positions. The combined weight of the driver, passengers, cargo, and any accessories or equipment added to your vehicle after it left the factory should never exceed your vehicle's capacity weight.
Page 258 Certification/Tire Label The Certification/Tire label also tells you the maximum weights for the front and rear axles, called Gross Axle Weight Rating (GAWR). To find out the actual loads on your front and rear axles, you need to go to a weigh station and weigh your vehicle.
Page 259 WARNING: (Continued) WARNING: on the vehicle can break, and it can change Things you put inside your vehicle can strike the way the vehicle handles. These could and injure people in a sudden stop or turn, cause you to lose control and crash. Also, or in a crash.
Page 260: Truck-Camper Loading Information
Two-Tiered Loading Add-On Equipment By positioning four 2 X 6 wooden planks across When you carry removable items, you may need the width of the pickup box, you can create an to put a limit on how many people you carry inside upper load platform.
Page 261: Pickup Conversion To Chassis Cab
Pickup Conversion to Chassis Cab Recreational Vehicle Towing We are aware that some vehicle owners might consider Recreational vehicle towing means towing the vehicle having the pickup box removed and a commercial or behind another vehicle such as behind a motorhome. recreational body installed.
Page 262: Dinghy Towing
Dinghy Towing Four-Wheel Drive Vehicles Two-Wheel Drive Vehicles Use the following procedure to dinghy tow a four-wheel-drive vehicle: If the vehicle is towed with all four wheels 1. Position the vehicle being towed behind the tow on the ground, the drivetrain components could be vehicle.
Page 263 3. Turn the engine off and firmly set the parking 5. Shift the transfer case to N (Neutral). See Shifting brake. See Parking Brake on page 3 33. into N (Neutral) under Four-Wheel Drive on page 3 28. 4. Securely attach the vehicle being towed to the tow vehicle.
Page 264: Dolly Towing
Dolly Towing Two-wheel-drive vehicles should not be towed with the rear wheels on the ground. Two-wheel-drive Front Towing (Front Wheels Off the transmissions have no provisions for internal lubrication while being towed. Ground) To dolly tow a two wheel drive vehicle, the vehicle must Two Wheel Drive Vehicles be towed with the rear wheels on the dolly.
Page 265 Four-Wheel-Drive Vehicles WARNING: Shifting a full time four wheel drive vehicle's transfer case into N (Neutral) can cause the vehicle to roll even if the automatic transmission is in P (Park) or the manual transmission is in any gear. You or others could be injured. Make sure the parking brake is firmly set before the transfer case is shifted to N (Neutral).
Page 266 Rear Towing (Rear Wheels Off the Ground) 3. Firmly set the parking brake. See Parking Brake on page 3 33. Two Wheel Drive Vehicles 4. Put an automatic transmission in P (Park) or a manual transmission in 1 (First). 5. Secure the vehicle to the dolly following the manufacturer's instructions.
Page 267 Four Wheel Drive Vehicles 5. Secure the vehicle to the dolly following the manufacturer's instructions. 6. Use an adequate clamping device designed for towing to ensure that the front wheels are locked into the straight position. WARNING: Shifting a full time four wheel drive vehicle's transfer case into N (Neutral) can cause the vehicle to roll even if the automatic transmission is in P (Park) or the manual transmission is in any...
Page 268: Towing A Trailer
Towing a Trailer Pulling a trailer improperly can damage the vehicle and result in costly repairs not covered by the vehicle warranty. To pull a trailer correctly, WARNING: follow the advice in this section and see your dealer/retailer for important information about towing a trailer with the vehicle.
Page 269: Pulling A Trailer
Pulling A Trailer Three important considerations have to do with weight: The weight of the trailer Here are some important points: The weight of the trailer tongue There are many different laws, including speed limit restrictions, having to do with trailering. Make The weight on the vehicle's tires sure the rig will be legal, not only where you live Weight of the Trailer...
Page 270 Vehicle Axle Ratio Maximum Trailer Weight GCWR* 2WD Regular Cab 2.9L L4 Automatic Transmission 3.73 3,400 lbs (1 542 kg) 7,000 lbs (3 175 kg) 2.9L L4 Manual Transmission 3.73 2,400 lbs (1 089 kg) 6,000 lbs (2 722 kg) 3.7L L5 Automatic Transmission 3.73 4,000 lbs (1 814 kg)
Page 271 Vehicle Axle Ratio Maximum Trailer Weight GCWR* 4WD Regular Cab 2.9L L4 Automatic Transmission 3.73 3,100 lbs (1 406 kg) 7,000 lbs (3 175 kg) 2.9L L4 Manual Transmission 3.73 2,100 lbs (953 kg) 6,000 lbs (2 722 kg) 3.7L L5 Automatic Transmission 3.73 4,000 lbs (1 814 kg) 9,000 lbs (4 082 kg)
Page 272: Weight Of The Trailer Tongue
Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total gross weight of the vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo carried in it, and the people who will be riding in the vehicle.
Page 273 Do not exceed the maximum allowable tongue weight Consider the following example: for the vehicle. Choose the shortest hitch extension that A vehicle model base weight is 5,500 lbs (2 495 kg); will position the hitch ball closest to the vehicle. This will 2,800 lbs (1 270 kg) at the front axle and 2,700 lbs help reduce the effect of trailer tongue weight on the (1 225 kg) at the rear axle.
Page 274 If the vehicle has many options and there is a front seat The effect of tongue weight is about 1.5 times the actual passenger and two rear seat passengers with some weight. Dividing the 900 lbs (408 kg) by 1.5 leaves only luggage and gear in the vehicle as well.
Page 275: Safety Chains
Hitches Safety Chains It is important to have the correct hitch equipment. Always attach chains between the vehicle and the Crosswinds, large trucks going by and rough roads are trailer. Cross the safety chains under the tongue of the a few reasons why the right hitch is needed. trailer to help prevent the tongue from contacting the road if it becomes separated from the hitch.
Page 276: Trailer Brakes
Trailer Brakes WARNING: (Continued) A loaded trailer that weighs more than 1,000 lbs (450 kg) needs to have its own brake system that is adequate for the weight of the trailer. Be sure to read To maximize safety when towing a trailer: and follow the instructions for the trailer brakes so they Have the exhaust system inspected for leaks are installed, adjusted and maintained properly.
Page 277: Following Distance
Following Distance Towing a trailer requires a certain amount of experience. Get to know the rig before setting out for Stay at least twice as far behind the vehicle ahead as the open road. Get acquainted with the feel of handling you would when driving the vehicle without a trailer.
Page 278: Making Turns
Making Turns Driving On Grades Making very sharp turns while trailering Reduce speed and shift to a lower gear before starting could cause the trailer to come in contact with the down a long or steep downgrade. If the transmission is vehicle.
Page 279: Parking On Hills
Parking on Hills 4. Reapply the brake pedal. Then apply the parking brake and shift into P (Park) for vehicles with an automatic transmission or into gear for vehicles WARNING: with a manual transmission. 5. If the vehicle has four-wheel-drive, be sure the transfer case is in a drive gear and not in Parking the vehicle on a hill with the trailer N (Neutral).
Page 280: Maintenance When Trailer Towing
Maintenance When Trailer Towing Trailer Recommendations The vehicle needs service more often when pulling a Subtract the hitch loads from the Cargo Weight Rating trailer. See Scheduled Maintenance on page 7 3 (CWR). CWR is the maximum weight of the load the or the Index for more information.
Page 281: Service And Appearance Care
Section 6 Service and Appearance Care Cooling System ....... . 6-26 Service .
Page 282 Section 6 Service and Appearance Care Leather ........6-105 Tires .
Page 283: Service
Accessories and Modifications Service When non dealer/non retailer accessories are added to For service and parts needs, visit your dealer/retailer. the vehicle, they can affect vehicle performance and You will receive genuine GM parts and GM-trained and safety, including such things as airbags, braking, supported service people.
Page 284: California Proposition 65 Warning
California Proposition 65 Warning Doing Your Own Service Work Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to WARNING: cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems, many fluids, and some component wear by-products contain You can be injured and the vehicle could be and/or emit these chemicals.
Page 285: Adding Equipment To The Outside Of The
Keep a record with all parts receipts and list the mileage and the date of any service work performed. See Maintenance Record on page 7 14. Adding Equipment to the Outside of the Vehicle Things added to the outside of the vehicle can affect the airflow around it.
Page 286: Gasoline Specifications
Gasoline Specifications Additives At a minimum, gasoline should meet ASTM To provide cleaner air, all gasolines in the United States specification D 4814 in the United States or are now required to contain additives that help prevent CAN/CGSB 3.5 or 3.511 in Canada. Some gasolines engine and fuel system deposits from forming, allowing contain an octane-enhancing additive called the emission control system to work properly.
Page 287: Fuels In Foreign Countries
Gasolines containing oxygenates, such as ethers and whether the fuel contains MMT. We recommend against ethanol, and reformulated gasolines might be available the use of such gasolines. Fuels containing MMT can in your area. We recommend that you use these reduce the life of spark plugs and the performance of gasolines, if they comply with the specifications the emission control system could be affected.
Page 288: Filling The Tank
Filling the Tank WARNING: Fuel vapor burns violently and a fuel fire can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the fuel pump island. Turn off the engine when refueling.
Page 289 on the Driver Information Center (DIC) and the check WARNING: engine light will be lit on the instrument panel cluster. See DIC Warnings and Messages on page 4 36 and Malfunction Indicator Lamp on page 4 28 for more Fuel can spray out on you if you open the fuel cap information.
Page 290: Filling A Portable Fuel Container
Filling a Portable Fuel Container Checking Things Under the Hood WARNING: WARNING: Never fill a portable fuel container while it is in the vehicle. Static electricity discharge from the Things that burn can get on hot engine parts and container can ignite the fuel vapor. You can be start a fire.
Page 291: Hood Release
Hood Release 2. Release the secondary latch on the hood. It is located below the front center of the hood. To open the hood, do the following: 3. Lift the hood. 1. Pull the handle with 4. Release the hood prop from its retainer and put the this symbol on it.
Page 292: Engine Compartment Overview
Engine Compartment Overview When you open the hood on the 3.7L engine (2.9L engine similar), you will see the following: 6-12 I n f o r ma t i o n P r o v i d e d b y :...
Page 293 A. Windshield Washer Fluid. See Adding Washer G. Radiator Pressure Cap. See Cooling System on Fluid under Windshield Washer Fluid on page 6 26. page 6 36. H. Remote Negative ( ) Terminal (GND). See Jump B. Engine Coolant Recovery Tank. See Engine Starting on page 6 41.
Page 294 When you open the hood on the 5.3L engine, you will see the following: 6-14 I n f o r ma t i o n P r o v i d e d b y :...
Page 295: Engine Oil
Engine Oil A. Engine Air Cleaner/Filter on page 6 20. B. Air Filter Restriction Indicator (If Equipped). See Checking Engine Oil Engine Air Cleaner/Filter on page 6 20. C. Windshield Washer Fluid Reservoir. See Adding It is a good idea to check the engine oil level at each Washer Fluid under Windshield Washer Fluid on fuel fill.
Page 296: When To Add Engine Oil
When to Add Engine Oil Notice: Do not add too much oil. If the engine has so much oil that the oil level gets above the cross-hatched area that shows the proper operating range, the engine could be damaged. See Engine Compartment Overview on page 6 12 for the location of the engine oil fill cap.
Page 297: What Kind Of Engine Oil To Use
What Kind of Engine Oil to Use Oils meeting these requirements should have Look for three things: the starburst symbol on GM6094M the container. This symbol indicates that the oil has Use only an oil that meets GM Standard been certified by the GM6094M.
Page 298: Engine Oil Life System
Cold Temperature Operation Engine Oil Life System If in an area of extreme cold, where the temperature When to Change Engine Oil falls below 20°F ( 29°C), use either an SAE 5W-30 synthetic oil or an SAE 0W-30 engine oil. Both provide This vehicle has a computer system that indicates when easier cold starting for the engine at extremely low to change the engine oil and filter.
Page 299: What To Do With Used Oil
How to Reset the Engine Oil Life What to Do with Used Oil System Used engine oil contains certain elements that can be unhealthy for your skin and could even cause cancer. The Engine Oil Life System calculates when to Do not let used oil stay on your skin for very long.
Page 300: Engine Air Cleaner/Filter
Engine Air Cleaner/Filter When to Inspect the Engine Air Cleaner/ Filter Inspect the air cleaner/filter at the Maintenance intervals and replace it at the first oil change after each 50,000 mile (80 000 km) interval. See Scheduled Maintenance on page 7 3 for more information. If you are driving in dusty/dirty conditions, inspect the filter at each engine oil change.
Page 301: Automatic Transmission Fluid
How to Check Automatic Transmission WARNING: Fluid Because this operation can be a little difficult, you may Operating the engine with the air cleaner/filter off choose to have this done at the dealer/retailer service can cause you or others to be burned. The air department.
Page 302: Checking The Fluid Level
Get the vehicle warmed up by driving about 24 km 3. With your foot on the brake pedal, move the shift (15 miles) when outside temperatures are above 10°C lever through each gear range, pausing for about (50°F). If it is colder than 10°C (50°F), drive the vehicle three seconds in each range.
Page 303 How to Add Automatic Transmission Fluid Refer to the Maintenance Schedule to determine what kind of transmission fluid to use. See Recommended Fluids and Lubricants on page 7 10. Add fluid only after checking the transmission fluid while it is hot. A cold check is used only as a reference. If the fluid level is low, add only enough of the proper fluid to bring the level up to the HOT area for a hot check.
Page 304: Manual Transmission Fluid
Manual Transmission Fluid After this is done: When to Check A good time to check the manual transmission fluid is when the engine oil is changed. However, the fluid in the manual transmission does not require changing. How to Check Because this operation can be a little difficult, you may choose to have this done at your GM dealer/retailer service department.
Page 305: How To Add Fluid
How to Add Fluid The hydraulic clutch fluid reservoir cap has this Here is how to add fluid. Refer to the Maintenance symbol on it. See Engine Schedule to determine what kind of fluid to use. See Compartment Overview Recommended Fluids and Lubricants on page 7 10. on page 6 12 for 1.
Page 306: When To Check And What To Use
When to Check and What to Use Cooling System The cooling system allows the engine to maintain the correct working temperature. Refer to the Maintenance Schedule to determine how often to check the fluid level in the clutch master 2.9L Engine shown (3.7L Engine similar) cylinder reservoir and for the proper fluid.
Page 307 WARNING: Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. Do not run the engine if there is a leak. If you run the engine, it could lose all coolant. That could cause an engine fire, and you could be burned.
Page 308: Engine Coolant
Engine Coolant Use a 50/50 mixture of clean, drinkable water and ® DEX-COOL coolant. If using this mixture, nothing else The cooling system in the vehicle is filled with needs to be added. This mixture: ® DEX-COOL engine coolant. This coolant is designed Gives freezing protection down to 34°F ( 37°C), to remain in the vehicle for five years or 150,000 miles outside temperature.
Page 309 Checking Coolant It is located toward the rear of the engine compartment on the passenger side of the vehicle. See Engine The vehicle must be on a level surface when checking Compartment Overview on page 6 12 for more the coolant level. information on location.
Page 310: How To Add Coolant To The Radiator
How to Add Coolant to the How to Add Coolant to the Radiator Recovery Tank WARNING: WARNING: An electric engine cooling fan under the hood can start up even when the engine is not running and You can be burned if you spill coolant on hot can cause injury.
Page 311 1. Remove the radiator pressure cap when the 4. Fill the coolant recovery tank to the cooling system, including the upper radiator hose, FULL COLD mark. is no longer hot. Turn the pressure cap slowly 5. Reinstall the cap on the coolant recovery tank, but counterclockwise about one full turn.
Page 312 7. By this time, the coolant level inside the radiator filler neck might be lower. If the level is lower, add ® more of the proper DEX COOL coolant mixture through the filler neck until the level reaches the base of the filler neck. 8.
Page 313: Engine Overheating
Engine Overheating If Steam is Coming from the Engine Compartment The vehicle has a coolant temperature gauge displayed on the instrument panel to warn if the engine is overheating. See Engine Coolant Temperature Gauge WARNING: on page 4 27. If the engine is too hot, the air conditioning might stop working.
Page 314: Engine Fan Noise
If No Steam is Coming from the Engine the vehicle slow for about 10 minutes. Keep a safe vehicle distance from the car in front of you. If the Compartment warning does not come back on, continue to drive normally. If an engine overheat warning is displayed but no steam can be seen or heard, the problem may not be too If the warning continues, pull over, stop, and park the...
Page 315: Power Steering Fluid
Power Steering Fluid How to Check Power Steering Fluid 1. Turn the key off and let the engine compartment The power steering fluid cool down. reservoir is located near the front of the engine 2. Wipe the cap and the top of the reservoir clean. compartment, behind the 3.
Page 316: Windshield Washer Fluid
Windshield Washer Fluid Notice: When using concentrated washer fluid, What to Use follow the manufacturer's instructions for adding water. When windshield washer fluid is needed, be sure to read the manufacturer's instructions before use. Do not mix water with ready-to-use washer If operating the vehicle in an area where the fluid.
Page 317: Brakes
Brakes Do not top off the brake fluid. Adding fluid does not correct a leak. If fluid is added when the linings are Brake Fluid worn, there will be too much fluid when new brake linings are installed. Add or remove brake fluid, as The brake master cylinder necessary, only when work is done on the brake reservoir is filled with...
Page 318: Checking Brake Fluid
Checking Brake Fluid WARNING: Check brake fluid by looking at the brake fluid reservoir. See Engine Compartment Overview on page 6 12. With the wrong kind of fluid in the brake hydraulic The fluid level should be system, the brakes might not work well. This could above the PP mark.
Page 319: Brake Wear
Brake Wear Properly torqued wheel nuts are necessary to help prevent brake pulsation. When tires are rotated, inspect This vehicle has front disc brakes and rear drum brake pads for wear and evenly tighten wheel nuts in brakes. the proper sequence to torque specifications in Capacities and Specifications on page 6 119.
Page 320: Battery
Brake Adjustment DANGER: Every brake stop, the brakes adjust for wear. Replacing Brake System Parts Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals The braking system on a vehicle is complex. Its many known to the State of California to cause cancer parts have to be of top quality and work well together if the vehicle is to have really good braking.
Page 321: Jump Starting
Jump Starting Notice: Ignoring these steps could result in costly damage to the vehicle that would not be covered by If the vehicle battery has run down, you may want to the warranty. use another vehicle and some jumper cables to start Trying to start the vehicle by pushing or pulling it your vehicle.
Page 322 Notice: If you leave the radio or other accessories on during the jump starting procedure, they could WARNING: be damaged. The repairs would not be covered by the warranty. Always turn off the radio and other Using a match near a battery can cause battery accessories when jump starting the vehicle.
Page 323 WARNING: Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running. 5. Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock.
Page 324 8. Now connect the black negative ( ) cable to the Notice: If the jumper cables are connected or negative ( ) terminal of the good battery. Use a removed in the wrong order, electrical shorting may remote negative ( ) terminal if the vehicle has one. occur and damage the vehicle.
Page 325: Rear Axle
How to Check Lubricant To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative ( ) cable from the vehicle that had the dead battery. 2. Disconnect the black negative ( ) cable from the vehicle with the good battery.
Page 326: Four-Wheel Drive
Four-Wheel Drive Lubricant checks in this section apply to this vehicle. There are two additional systems that need lubrication. Transfer Case When to Check Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant. See Scheduled Maintenance on page 7 3.
Page 327: Front Axle
Front Axle If the level is below the bottom of the filler plug hole, located on the front axle, you may need to add some lubricant. When to Check and Change Lubricant When the differential is cold, add enough lubricant to It is not necessary to regularly check your front axle raise the level to 1/2 inch (12 mm) below the filler fluid unless you suspect there is a leak or you hear an...
Page 328: Bulb Replacement
Headlamps Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 6 52. For any bulb changing procedure not listed in this section, contact your dealer/retailer. Halogen Bulbs WARNING: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb.
Page 329: Front Turn Signal, Parking And Daytime Running Lamps (Drl)
Front Turn Signal, Parking and Daytime Running Lamps (DRL) To replace one of these bulbs: 1. Open the hood. See Hood Release on page 6 11. 3. Turn the bulb socket counterclockwise to remove it from the headlamp assembly and pull it straight out.
Page 330: Center High-Mounted Stoplamp (Chmsl)
4. Holding the socket, pull the old bulb to release it 5. Insert the bulb socket into the lamp assembly and from the bulb socket. turn it clockwise to secure. 5. Push the new bulb into the socket until it clicks. 6.
Page 331: License Plate Lamp
License Plate Lamp 2. Remove the two rear lamp assembly screws To replace one of these bulbs: near the tailgate latch. 3. Pull the lamp assembly away from the vehicle. 4. Turn the bulb socket counterclockwise to remove it 1. Reach under the rear bumper for the bulb socket. from the taillamp assembly.
Page 332: Replacement Bulbs
Replacement Bulbs Windshield Wiper Blade Replacement Exterior Lamp Bulb Number Center High Mounted Windshield wiper blades should be inspected for wear Stoplamp (CHMSL) and cracking. See Scheduled Maintenance on License Plate Bulb page 7 3 for more information. Headlamps Replacement blades come in different types and are removed in different ways.
Page 333 2. Press down on the blade assembly pivot locking tab. Pull down on the blade assembly to release it from the wiper arm hook. 3. Remove the insert from the blade assembly. The insert has two notches at one end that are locked by bottom claws of the blade assembly.
Page 334 4. To install the new wiper insert, slide the insert (D), notched end last, into the end with two blade claws (A). Slide the insert all the way through the A. Claw in Notch blade claws at the opposite end (B). The plastic caps (C) will be forced off as the insert is fully B.
Page 335: Tires
Tires WARNING: (Continued) Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever Underinflated tires pose the same danger have questions about your tire warranty and as overloaded tires. The resulting where to obtain service, see your vehicle accident could cause serious injury.
Page 336: Tire Sidewall Labeling
Tire Sidewall Labeling (A) Tire Size The tire size is a combination of letters and numbers used to define a particular Useful information about a tire is molded into its tire's width, height, aspect ratio, construction type sidewall. The examples below show a typical and service description.
Page 337 (E) Tire Ply Material The type of cord and number of plies in the sidewall and under the tread. (F) Uniform Tire Quality Grading (UTQG) Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction and temperature resistance. For more information see Uniform Tire Quality Grading on page 6 74.
Page 338 (B) Tire Ply Material The type of cord and (E) Tire Inflation The temporary use tire or number of plies in the sidewall and under the compact spare tire should be inflated to 60 psi tread. (420 kPa). For more information on tire pressure and inflation see Inflation - Tire Pressure on (C) Tire Identification Number (TIN) The Tire...
Page 339: Tire Size
Tire Size (C) Aspect Ratio A two digit number that indicates the tire height to width measurements. The following illustration shows an example of a For example, if the tire size aspect ratio is 70, as typical passenger vehicle tire size. shown in item C of the illustration, it would mean that the tire's sidewall is 70 percent as high as it is wide.
Page 340: Tire Terminology And Definitions
Tire Terminology and Definitions Bias Ply Tire A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees Air Pressure The amount of air inside the tire to the centerline of the tread. pressing outward on each square inch of the tire. Cold Tire Pressure The amount of air pressure Air pressure is expressed in pounds per square...
Page 341 GVWR Gross Vehicle Weight Rating. See Maximum Loaded Vehicle Weight The sum of Loading the Vehicle on page 5 31. curb weight, accessory weight, vehicle capacity weight, and production options weight. GAWR FRT Gross Axle Weight Rating for the front axle. See Loading the Vehicle on page 5 31. Normal Occupant Weight The number of occupants a vehicle is designed to seat multiplied...
Page 342 Radial Ply Tire A pneumatic tire in which the UTQGS (Uniform Tire Quality Grading ply cords that extend to the beads are laid at Standards) A tire information system that 90 degrees to the centerline of the tread. provides consumers with ratings for a tire's traction, temperature, and treadwear.
Page 343: Inflation - Tire Pressure
Inflation - Tire Pressure A vehicle specific Tire and Loading Information label is attached to your vehicle. This label shows Tires need the correct amount of air pressure to your vehicle's original equipment tires and the operate effectively. correct inflation pressures for your tires when they are cold.
Page 344: High-Speed Operation
How to Check High-Speed Operation Use a good quality pocket-type gauge to check tire pressure. You cannot tell if your tires are WARNING: properly inflated simply by looking at them. Radial tires may look properly inflated even Driving at high speeds, 160 km/h (100 mph) or when they are underinflated.
Page 345: Tire Pressure Monitor System
Tire Pressure Monitor System If your vehicle has P235/50R18 size tires, they will require inflation pressure adjustment when driving your The Tire Pressure Monitor System (TPMS) uses radio vehicle at speeds of 100 mph (160 km/h) or higher. Set and sensor technology to check tire pressure levels. the cold inflation pressure to the maximum inflation The TPMS sensors monitor the air pressure in your pressure shown on the tire sidewall, or 35 psi (241 kPa),...
Page 346: Tire Pressure Monitor Operation
Federal Communications Commission Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver's responsibility to (FCC) and Industry Canada maintain correct tire pressure, even if under inflation has not reached the level to trigger illumination of the See Radio Frequency Statement on page 8 20 for TPMS low tire pressure telltale.
Page 347: Tpms Malfunction Light And Message
TPMS Malfunction Light and Message message come on at each ignition cycle until the tires are inflated to the correct inflation pressure. For The TPMS will not function properly if one or more of additional information and details about the DIC the TPMS sensors are missing or inoperable.
Page 348: Tpms Sensor Matching Process
One or more TPMS sensors are missing or TPMS Sensor Matching Process damaged. The DIC message and the TPMS Each TPMS sensor has a unique identification code. malfunction light should go off when the TPMS sensors are installed and the sensor matching Any time you replace one or more of the TPMS sensors or rotate your vehicle's tires, the identification codes process is performed successfully.
Page 349 The TPMS sensor matching procedure is outlined 6. Proceed to the passenger side front tire, and below: repeat the procedure in Step 5. 1. Set the parking brake. 7. Proceed to the passenger side rear tire, and repeat the procedure in Step 5. 2.
Page 350: Tire Inspection And Rotation
Tire Inspection and Rotation We recommend that you regularly inspect your vehicle's tires, including the spare tire, for signs of wear or damage. See When It Is Time for New Tires on page 6 71 for more information. Tires should be rotated every 5,000 to 8,000 miles (8 000 to 13 000 km).
Page 351: When It Is Time For New Tires
When It Is Time for New Tires Reset the Tire Pressure Monitor System. See Tire Pressure Monitor Operation on page 6 66. Various factors, such as maintenance, temperatures, Make certain that all wheel nuts are properly driving speeds, vehicle loading, and road conditions, tightened.
Page 352: Buying New Tires
Buying New Tires You need new tires if any of the following statements are true: GM has developed and matched specific tires for your You can see the indicators at three or more places vehicle. The original equipment tires installed on your around the tire.
Page 353 WARNING: WARNING: (Continued) could fail suddenly, causing a crash. Use Mixing tires could cause you to lose control of your vehicle while driving. If you mix tires of only radial-ply tires with the wheels on the different sizes, brands, or types (radial and vehicle.
Page 354: Different Size Tires And Wheels
Different Size Tires and Wheels Uniform Tire Quality Grading If you add wheels or tires that are a different size than Quality grades can be found where applicable on your original equipment wheels and tires, this may the tire sidewall between tread shoulder and affect the way your vehicle performs, including its maximum section width.
Page 355 Traction AA, A, B, C While the tires available on General Motors passenger cars and light trucks may vary with The traction grades, from highest to lowest, respect to these grades, they must also conform are AA, A, B, and C. Those grades represent to federal safety requirements and additional the tire's ability to stop on wet pavement as General Motors Tire Performance Criteria (TPC)
Page 356: Wheel Alignment And Tire Balance
Wheel Replacement Sustained high temperature can cause the material of the tire to degenerate and reduce tire Replace any wheel that is bent, cracked, or badly life, and excessive temperature can lead to rusted or corroded. If wheel nuts keep coming loose, sudden tire failure.
Page 357: Used Replacement Wheels
Used Replacement Wheels WARNING: WARNING: Using the wrong replacement wheels, wheel bolts, or wheel nuts on your vehicle can be dangerous. Putting a used wheel on the vehicle is dangerous. It could affect the braking and handling of your You cannot know how it has been used or how far vehicle, make your tires lose air and make you it has been driven.
Page 358: Tire Chains
Tire Chains Notice: If your vehicle has a tire size other than P215/70R16, P235/75R16, P265/70R17, or P235/50R18 use tire chains only where legal and WARNING: only when you must. Use chains that are the proper size for your tires. Install them on the tires of the rear axle.
Page 359: If A Tire Goes Flat
If a Tire Goes Flat WARNING: It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle's tires properly. If air goes out of a tire, it is much more likely to leak out Lifting a vehicle and getting under it to do slowly.
Page 360: Changing A Flat Tire
Changing a Flat Tire WARNING: (Continued) If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on 3. If you have a four-wheel-drive vehicle, be sure page 4 3.
Page 361: Removing The Spare Tire And Tools
Removing the Spare Tire and Tools A. Wheel Block B. Flat Tire A. Wing Nut The following information explains how to use the jack B. Storage Bag and Tools and change a tire. The tools you will need are located under the right front passenger seat.
Page 362 Put the tools to the side while you access the jack and wheel blocks. Regular/Extended Cab For regular and extended cab vehicles, the jack and wheel blocks are located under the cover at the center of the vehicle behind the front seats. A.
Page 363 Crew Cab For crew cab models, the jack and wheel blocks are located under the driver side rear seat. 1. Reach under the rear seat to access the jack and wheel blocks. A. Jack Handle C. Jack Handle Extensions D. Wheel Wrench B.
Page 364 1. Assemble the wheel wrench (D), the jack handle extensions (A) and the jack handle (C) as shown. 2. Insert the chiseled end of the jack handle (C) at a slight angle through the hole in the rear bumper and into the funnel-shaped guide. 3.
Page 365: Spare Tire
Removing the Flat Tire and Installing 4. Tilt the retainer when the tire has been the Spare Tire lowered, and slide it up the cable so it can be Use the following pictures and instructions to remove pulled up through the the flat tire and raise the vehicle.
Page 366 2. Remove the center cap by placing the chisel end 3. Use the wheel wrench to loosen all the wheel nuts of the wheel wrench (E) into one of the slots on the by turning it counterclockwise. Do not remove the wheel and gently prying the cap out.
Page 367 WARNING: Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle.
Page 368 Front Position Front Position If the flat tire is on the front of the vehicle, position For Extended Fuel Economy (XFE) vehicles, the jack to the rear of the front tire in the pocket off position the jack on the flat portion of the jacking of the frame.
Page 369 7. Remove all the wheel nuts and the flat tire. Rear Position If the flat tire is on the rear, position the jack under the rear axle and get as close as possible to the shock absorber. 5. Make sure the jack head is positioned so that the rear axle is resting securely between the grooves that are on the jack head.
Page 370 WARNING: WARNING: Rust or dirt on a wheel, or on the parts to which it Never use oil or grease on bolts or nuts because is fastened, can make wheel nuts become loose the nuts might come loose. The vehicle's wheel after time.
Page 371 Front Position Rear Position 11. Turn the wheel wrench counterclockwise to lower the vehicle. Lower the jack completely. I n f o r ma t i o n P r o v i d e d b y : 6-91...
Page 372 12. Tighten the wheel nuts WARNING: firmly in a crisscross sequence as shown by turning the wheel Wheel nuts that are improperly or incorrectly wrench clockwise. tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing.
Page 373: Secondary Latch System
Secondary Latch System To release the spare tire from the secondary latch: 1. Check under the Your vehicle has an underbody mounted tire hoist vehicle to see if the assembly that has a secondary latch system. It is cable end fitting is designed to stop the spare tire from suddenly falling off visible.
Page 374 5. Turn the wrench counterclockwise until approximately 6 inches (15 cm) of cable is exposed. 6. Stand the wheel blocks on their shortest ends, with the backs facing each other. 7. Place the bottom edge of the jack (A) on the wheel blocks (B), separating them so that the jack is balanced...
Page 375 WARNING: Someone standing too close during the procedure could be injured by the jack. If the spare tire does not slide off the jack completely, make sure no one is behind you or on either side of you as you pull the jack out from under the spare.
Page 376: Storing A Flat Or Spare Tire And Tools
Storing a Flat or Spare Tire and Tools WARNING: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.
Page 377 Store the tire under the rear of the vehicle in the spare tire carrier. 1. Put the tire on the ground at the rear of the vehicle with the valve stem pointed down. 3. Assemble the wheel wrench, the jack handle extensions, and the jack handle as shown.
Page 378 5. Turn the wheel wrench clockwise to raise the tire part way up. Make sure the retainer is seated in the wheel opening and the valve stem is pointed down. Continue raising the tire, watch to make sure it does not get caught on anything on the underbody. If the tire does get caught, loosen two or three turns and push and pull the tire and then retighten.
Page 379 To store the tools: 1. Return the tools to the storage bag. 2. Attach the storage bag to the floor under the front passenger seat. 3. Reinstall the wing nut to secure the bag to the vehicle. 7. Make sure the tire is stored securely. Push, pull (A), and then try to turn (B) the tire.
Page 380 To store the jack and wheel blocks: Regular/Extended Cab 5. Put the cover in position and insert and tighten the wing nut to secure it. A. Jack B. Wheel Blocks C. Wing Nut 1. Install the wheel blocks (B) first. 2.
Page 381 Crew Cab 2. Reinstall the jack and wheel block assembly in the mounting bracket. Be sure to position the holes in the base of the jack onto the pins in the mounting bracket. 3. Turn the handle to raise the jack until it is secure, but do not overtighten the jack in the bracket.
Page 382: Spare Tire
Spare Tire Notice: When the compact spare is installed, do not take the vehicle through an automatic car wash with Compact Spare Tire guide rails. The compact spare can get caught on the rails which can damage the tire, wheel and other Your vehicle may have a compact spare tire.
Page 383: Appearance Care
Your vehicle may have a different size spare tire than Appearance Care the road tires originally installed on your vehicle. This spare was developed for use on your vehicle, so it is Interior Cleaning alright to drive on it. If your vehicle has four-wheel drive and the different size spare tire is installed, keep the The vehicle's interior will continue to look its best if it is vehicle in two-wheel drive.
Page 384 Use glass cleaner only on glass. Remove any Do not clean the vehicle using: accidental over-spray from other surfaces immediately. A knife or any other sharp object to remove a soil To prevent over-spray, apply cleaner directly to the from any interior surface. cleaning cloth.
Page 385: Fabric/Carpet
Fabric/Carpet If any of the soil remains, a commercial fabric cleaner or spot lifter may be necessary. When a commercial Use a vacuum cleaner with a soft brush attachment upholstery cleaner or spot lifter is to be used, test a frequently to remove dust and loose dirt.
Page 386: Care Of Safety Belts
Instrument Panel, Vinyl, and Other Care of Safety Belts Plastic Surfaces Keep belts clean and dry. A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary, WARNING: a clean soft cloth dampened with a mild soap solution can be used to gently remove dust and dirt.
Page 387: Washing Your Vehicle
Washing Your Vehicle Rinse the vehicle well, before washing and after to remove all cleaning agents completely. If they are The best way to preserve the vehicle's finish is to keep allowed to dry on the surface, they could stain. it clean by washing it often.
Page 388: Finish Care
Finish Care Protecting Exterior Bright Metal Parts Bright metal parts should be cleaned regularly to keep Occasional waxing or mild polishing of the vehicle by their luster. Washing with water is all that is usually hand may be necessary to remove residue from the needed.
Page 389: Aluminum Or Chrome-Plated Wheels
Aluminum or Chrome-Plated Wheels The surface of these wheels is similar to the painted surface of the vehicle. Do not use strong soaps, and Trim chemicals, abrasive polishes, abrasive cleaners, cleaners with acid, or abrasive cleaning brushes on The vehicle may have either aluminum or them because they could damage the surface.
Page 390: Tires
Tires Underbody Maintenance To clean the tires, use a stiff brush with tire cleaner. Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not Notice: Using petroleum-based tire dressing removed, corrosion and rust can develop on the products on the vehicle may damage the paint finish underbody parts such as fuel lines, frame, floor pan, and/or tires.
Page 391: Vehicle Identification
Engine Identification Vehicle Identification The eighth character in the VIN is the engine code. This Vehicle Identification Number (VIN) code identifies the vehicle's engine, specifications, and replacement parts. See Engine Specifications under Capacities and Specifications on page 6 119 for the vehicle's engine code.
Page 392: Electrical System
Windshield Wiper Fuses Electrical System The windshield wiper motor is protected by a circuit Add-On Electrical Equipment breaker and a fuse. If the motor overheats due to heavy snow, etc., the wiper will stop until the motor cools. Notice: Do not add anything electrical to the vehicle If the overload is caused by some electrical problem, unless you check with your dealer/retailer first.
Page 393: Engine Compartment Fuse Block
Engine Compartment Fuse Block To remove the cover, push in on the tab on the end of the cover and lift. To reinstall the cover, line up the tab and push down on the cover until the tab clicks into place.
Page 394 6-114 I n f o r ma t i o n P r o v i d e d b y :...
Page 395 Fuses Usage ABS 2 ABS 2 (ABS Pump) AUX PWR 1 Accessory Power 1 AUX PWR 2 Accessory Power 2 BCK/UP Back-up Lights BLWR Climate Control Fan CLSTR Cluster CNSTR VENT Fuel Canister Vent Solenoid Cruise Control Switch, Inside Rearview Mirror, Transfer Case CRUISE Control Module, Brake Switch, Clutch Disable...
Page 396 Fuses Usage Fuses Usage BACKUP LAMP Backup Lamp Regulated Voltage Control HORN Horn S/ROOF Sunroof (If Equipped) HTD/SEAT Heated Seat (If Equipped) STOP Stop Lamps Ignition, Clutch Starter Switch, Neutral STRTR Starter Solenoid Relay Safety Back Up Switch, Ignition Truck Body Controller Coils 1 5, Air Conditioning Relay Transmission Control Module Injectors...
Page 397 Relays Usage Relays Usage A/C CMPRSR Air Conditioning Compressor Run/Crank, Airbag System Fuse, Cruise Control Fuse, Ignition Fuse, BEAM SEL Beam Selection RUN/CRNK Back-Up Lamps, ABS Fuse, Front Daylight Running Lamps Axle, PCM-1, Injectors Fuse, FOG/LAMP Fog Lamps (If Equipped) Transmission Fuse, ERLS BK UP LP Back Up Lamp...
Page 398 2.9L and 3.7L 5.3L Fuses Usage Trailer Park Lamp Communication Interface Module Supplemental Inflatable Restraint System, Sensing and Diagnostic Module Trailer Auxiliary Maxi-Fuse 6-118 I n f o r ma t i o n P r o v i d e d b y :...
Page 399: Capacities And Specifications
Capacities and Specifications The following approximate conversion capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 7 10 for more information. Capacities and Specifications Capacities Application Metric English For the air conditioning system refrigerant charge amount, see the refrigerant caution label located Air Conditioning Refrigerant R134a under the hood.
Page 400 Capacities and Specifications (cont'd) Capacities Application Metric English Transmission Automatic (Pan Removal and Filter Replacement) 4.7 L 5.0 qt Manual Rear-Wheel Drive (Drain and Refill) 2.2 L 2.3 qt Manual Four-Wheel Drive (Drain and Refill) 2.3 L 2.4 qt Wheel Nut Torque 100 lb ft All capacities are approximate.
Page 401 Section 7 Maintenance Schedule Maintenance Schedule ......7-2 Recommended Fluids and Lubricants ..7-10 Introduction .
Page 402: Maintenance Schedule
Maintenance Schedule The maintenance schedule is for vehicles that: carry passengers and cargo within recommended limits on the Tire and Loading Information label. Introduction See Loading the Vehicle on page 5 31. Maintenance intervals, checks, inspections, are driven on reasonable road surfaces within legal recommended fluids, and lubricants are necessary driving limits.
Page 403: Scheduled Maintenance
Scheduled Maintenance At your dealer/retailer, you can be certain that you will receive the highest level of service available. Your When the Change Oil Message Displays dealer/retailer has specially trained service technicians, uses genuine replacement parts, as well as, up to date Change engine oil and filter.
Page 404 Fluids visual leak check (or every 12 months, When the Change Oil message displays, certain whichever occurs first). A leak in any system must services, checks, and inspections are required. The be repaired and the fluid level checked. services described for Maintenance should be performed at every engine oil change.
Page 405: Additional Required Services
Body hinges and latches, key lock cylinders, and Additional Required Services folding seat hardware lubrication. Lubricate hood safety lever pivot and prop rod pivot and tailgate At Each Fuel Stop latch bolt, handle assembly pivot points, and Engine oil level check. See Engine Oil on hinges.
Page 406 Engine cooling system and pressure cap pressure First Engine Oil Change After Every check. Radiator and air conditioning condenser 160 000 km/100,000 Miles outside cleaning. See Cooling System on page 6 26. Automatic transmission fluid change (normal service). See Automatic Transmission Fluid on Exhaust system and nearby heat shields page 6 21.
Page 407 Scheduled Maintenance Service Maintenance Maintenance Change engine oil and filter. Reset oil life system. Engine coolant level check. Windshield washer fluid level check. Tire inflation pressures check. Tire wear inspection. Rotate tires. Fluids visual leak check. Engine air cleaner filter inspection (vehicles driven in dusty conditions only). Brake system inspection.
Page 408: Owner Checks And Services
Owner Checks and Services down all the way to the floor. If the starter works when the clutch pedal is not pushed all the way Starter Switch Check down, your vehicle needs service. Automatic Transmission Shift Lock WARNING: Control System Check WARNING: When you are doing this inspection, the vehicle could move suddenly.
Page 409: Ignition Transmission Lock Check
Ignition Transmission Lock Check Parking Brake and Automatic Transmission P (Park) Mechanism While parked, and with the parking brake set, try to turn Check the ignition to LOCK/OFF in each shift lever position. For automatic transmission vehicles, the ignition should turn to LOCK/OFF only when the shift lever WARNING: is in P (Park).
Page 410: Recommended Fluids And Lubricants
Recommended Fluids and Usage Fluid/Lubricant Lubricants Chassis Lubricant (GM Part No. Parking Brake U.S. 12377985, in Canada 88901242) Fluids and lubricants identified below by name, part Cable Guides or lubricant meeting requirements of number, or specification can be obtained from your NLGI #2, Category LB or GC-LB.
Page 411 Usage Fluid/Lubricant Usage Fluid/Lubricant SAE 75W-90 Synthetic Axle Lubricant Hood and Door Front and (GM Part No. U.S. 89021677, Hinges, Body Rear Axle in Canada 89021678). Door Hinge Multi-Purpose Lubricant, Superlube Pins, Liftgate Synchromesh Transmission Fluid (GM Part No. U.S. 12346241, Hinge and Transfer Case (GM Part No.
Page 412: Maintenance Replacement Parts
Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your dealer/retailer. Part GM Part Number ACDelco Part Number Engine Air Cleaner/Filter 15942429 Engine Oil Filter 2.9L L4 Engine 19210283 PF46 3.7L L5 Engine 19210285 PF61 5.3L V8 Engine...
Page 413: Engine Drive Belt Routing
Engine Drive Belt Routing 5.3L Engine 2.9L and 3.7L Engines I n f o r ma t i o n P r o v i d e d b y : 7-13...
Page 414: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. Retain all maintenance receipts. Maintenance Record Odometer Date Serviced By Services Performed Reading 7-14 I n f o r ma t i o n P r o v i d e d b y :...
Page 415 Maintenance Record (cont'd) Odometer Date Serviced By Services Performed Reading I n f o r ma t i o n P r o v i d e d b y : 7-15...
Page 416 Maintenance Record (cont'd) Odometer Date Serviced By Services Performed Reading 7-16 I n f o r ma t i o n P r o v i d e d b y :...
Page 417: Customer Assistance Information
Section 8 Customer Assistance Information Customer Assistance and Information ... 8-2 Reporting Safety Defects ......8-16 Customer Satisfaction Procedure .
Page 418: Customer Assistance And Information
Information resolved by the dealership without further help, in the U.S., call the Chevrolet Customer Assistance Center at 1-800-222-1020. In Canada, call General Motors of Customer Satisfaction Procedure Canada Customer Communication Centre at Your satisfaction and goodwill are important to your 1-800-263-3777 (English), or 1-800-263-7854 (French).
Page 419 STEP THREE U.S. Owners: Both General Motors You may contact the BBB Auto Line Program using the and your dealer are committed to making sure you are toll-free telephone number or write them at the following completely satisfied with your new vehicle. However, address: if you continue to remain unsatisfied after following the BBB Auto Line Program...
Page 420 STEP THREE Canadian Owners: In the event that For further information concerning eligibility in the you do not feel your concerns have been addressed Canadian Motor Vehicle Arbitration Plan (CAMVAP), call after following the procedure outlined in Steps 1 and 2, toll-free 1-800-207-0685, or call the General Motors General Motors of Canada Limited wants you to be Customer Communication Centre, 1-800-263-3777...
Page 421: Online Owner Center
My Showroom: Find and save information on vehicles and current offers in your area. Online service and maintenance records My Dealers/Retailers: Save details such as Find Chevrolet dealers for service nationwide address and phone number for each of your Exclusive privileges and offers preferred GM dealers/retailers.
Page 422: Customer Assistance For Text Telephone (Tty)
Oshawa, Ontario L1H 8P7 gmcanada.com Chevrolet encourages customers to call the toll-free number for assistance. However, if a customer wishes 1-800-263-3777 (English) to write or e-mail Chevrolet, the letter should be 1-800-263-7854 (French) addressed to: 1-800-263-3830 (For Text Telephone devices (TTYs))
Page 423: Gm Mobility Reimbursement Program
Overseas Customer Assistance GM Mobility Reimbursement Program Please contact the local General Motors Business Unit. Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) Customer Assistance General Motors de Mexico, S. de R.L. de C.V. Customer Assistance Center Paseo de la Reforma # 2740 This program, available to qualified applicants, can Col.
Page 424: Roadside Assistance Program
Service is available 24 hours a day, 365 days a year. Roadside Assistance is not a part of the New Vehicle Calling for Assistance Limited Warranty. Chevrolet and General Motors of Canada Limited reserve the right to make any changes When calling Roadside Assistance, have the following...
Page 425: Services Provided
Emergency Tow From a Public Road or Services Specific to Canadian Highway: Tow to the nearest Chevrolet dealer for Purchased Vehicles warranty service, or if the vehicle was in a crash and cannot be driven. Assistance is also given...
Page 426: Scheduling Service Appointments
Trip Interruption Benefits and Assistance: Must Scheduling Service Appointments be over 250 km from where your trip was started to qualify. General Motors of Canada Limited requires When your vehicle requires warranty service, contact pre-authorization, original detailed receipts, and a your dealer/retailer and request an appointment.
Page 427: Courtesy Transportation Program
Courtesy Transportation Program Transportation Options Warranty service can generally be completed while To enhance your ownership experience, we and our you wait. However, if you are unable to wait, GM participating dealers are proud to offer Courtesy helps to minimize your inconvenience by providing Transportation, a customer support program for vehicles several transportation options.
Page 428: Additional Program Information
Additional Program Information Claim amounts should reflect actual costs and be supported by original receipts. See your dealer for All program options, such as shuttle service, may not be information regarding the allowance amounts for available at every dealer. Please contact your dealer for reimbursement of fuel or other transportation costs.
Page 429: Repair Facility
Collision Parts Aftermarket collision parts are also available. These are made by companies other than GM and may not have Genuine GM Collision parts are new parts made with been tested for your vehicle. As a result, these parts the same materials and construction methods as the may fit poorly, exhibit premature durability/corrosion parts with which your vehicle was originally built.
Page 430: Insuring Your Vehicle
Insuring Your Vehicle If a Crash Occurs Protect your investment in your GM vehicle with Here is what to do if you are involved in a crash. comprehensive and collision insurance coverage. Check to make sure that you are all right. If you There are significant differences in the quality of are uninjured, make sure that no one else in your coverage afforded by various insurance policy terms.
Page 431 Gather the important information you will need from Managing the Vehicle Damage Repair the other driver. Things like name, address, phone Process number, driver's license number, vehicle license plate, vehicle make, model and model year, In the event that your vehicle requires damage repairs, Vehicle Identification Number (VIN), insurance GM recommends that you take an active role in its company and policy number, and a general...
Page 432: Reporting Safety Defects
Reporting Safety Defects To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); Reporting Safety Defects to the go to http://www.safercar.gov or write to: United States Government Administrator, NHTSA If you believe that your vehicle has a defect which 1200 New Jersey Avenue, S.E.
Page 433: Reporting Safety Defects To General Motors
Service Manuals have the diagnosis and repair Call 1-800-222-1020, or write: information on engines, transmission, axle suspension, Chevrolet Motor Division brakes, electrical, steering, body, etc. Chevrolet Customer Assistance Center Service Bulletins P.O. Box 33170 Detroit, MI 48232-5170 Service Bulletins give additional technical service...
Page 434: Vehicle Data Recording And Privacy
Current and Past Model Order Forms Vehicle Data Recording and Privacy Technical Service Bulletins and Manuals are available for current and past model GM vehicles. To request an Your GM vehicle has a number of sophisticated order form, specify year and model name of the vehicle. computers that record information about the vehicle s ORDER TOLL FREE: 1-800-551-4123 performance and how it is driven.
Page 435: Event Data Recorders
Event Data Recorders Important: EDR data is recorded by your vehicle only if a non-trivial crash situation occurs; no data is recorded This vehicle has an Event Data Recorder (EDR). by the EDR under normal driving conditions and no The main purpose of an EDR is to record, in certain personal data (e.g., name, gender, age, and crash crash or near crash-like situations, such as an airbag location) is recorded.
Page 436: Onstar
® OnStar Radio Frequency Statement If the vehicle has OnStar and you subscribe to the This vehicle has systems that operate on a radio OnStar services, please refer to the OnStar Terms and frequency that comply with Part 15 of the Federal Conditions for information on data collection and use.
Page 437: Instrument Panel, Vinyl, And Other Plastic
Antenna Fixed Mast ........4-61 Accessories and Modifications .
Page 438 Bulb Replacement ....... . . 6-52 Audio System ........4-41 Radio Reception .
Page 439 Cleaning (cont.) CD, MP3 ......... . 4-55 Center Console Storage .
Page 440 Driving Customer Assistance ....... .8-6 Offices ..........8-6 At Night .
Page 441: Front Turn Signal, Parking And Daytime
Electronic Immobilizer Operation ® PASS-Key III+ ........3-16 Filter Engine Engine Air Cleaner .
Page 442 Fuel (cont.) Filling the Tank ........6-8 Halogen Bulbs .
Page 443 Ignition Positions ........3-19 Labeling, Tire Sidewall ......6-56 Infants and Young Children, Restraints .
Page 444 Lights (cont.) Flash-to-Pass ........4-5 Maintenance Schedule High/Low Beam Changer .
Page 445 New Vehicle Break-In ......3-18 Paint, Damage ........6-110 Park Shifting Into .
Page 446 Recommended Fluids and Lubricants ... . . 7-10 Privacy ..........8-18 OnStar .
Page 447 Securing a Child Restraint Center Front Seat Position ..... . . 2-62 Safety Belts Rear Seat Position ....... 2-59 Care of .
Page 448: Aluminum Or Chrome-Plated Wheels
® StabiliTrak /TCS Warning Light ....4-26 Tilt Wheel ..........4-3 Starting the Engine .
Page 449 Tires (cont.) Wheel Alignment and Tire Balance ....6-76 Uniform Tire Quality Grading ..... . 6-74 Wheel Replacement .
Page 450 Wheels Windshield Alignment and Tire Balance ..... . 6-76 Washer ..........4-6 Different Size .

Chevrolet 2010 Colorado Owner's Manual

Section 2 Seats and Restraint System

Section 3 Features and Controls

Section 4 Instrument Panel

Section 5 Driving Your Vehicle

Section 6 Service and Appearance Care

Quick Links

Chapters

Related Manuals for Chevrolet 2010 Colorado

Summary of Contents for Chevrolet 2010 Colorado