Page 1 ..........1-1 Instrument Panel .
Page 2: Table Of Contents
....6-1 Service ......... . . 6-4 Fuel .
Page 3 For vehicles first sold in Canada, substitute the name General Motors of Canada Limited for Chevrolet Motor Division wherever it appears in this manual. If your vehicle is a Two-mode Hybrid, see the Two-mode Hybrid manual for more information.
Page 4: Service
Warning messages found on vehicle labels and in this manual describe hazards and what to do to avoid or reduce them. indicates a hazard with a high level of risk which will result in serious injury or death. indicates a hazard that could result in injury or death.
Page 5: Fuel
Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the Index. Airbag Readiness Light Air Conditioning Antilock Brake System (ABS) Audio Steering Wheel Controls or OnStar Brake System Warning Light Charging System Cruise Control...
Page 7: Head Restraints
........1-2 ......1-4 Remote Keyless Entry (RKE) System .
Page 9: Instrument Panel
A. Outlet Adjustment on page 4 27. B. Turn Signal/Multifunction Lever on page 4 4. C. Instrument Panel Cluster on page 4 31. D. Hazard Warning Flashers on page 4 3. E. Shift Lever. See Automatic Transmission Operation on page 3 33. F.
Page 10 This section provides a brief overview about some of the important features that may or may not be on your specific vehicle. For more detailed information, refer to each of the features which can be found later in this owner manual. The RKE transmitter is used to remotely lock and unlock the doors from up to 60 m (195 feet) away from the vehicle.
Page 11 1. Aim the RKE transmitter at the vehicle. 2. Press 3. Immediately after completing Step 2, press and hold until the turn signal lamps flash. When the vehicle starts, the parking lamps will turn on and remain on as long as the engine is running. The doors will be locked and the climate control system may come on.
Page 12 Use the Remote Keyless Entry (RKE) transmitter or the power door lock switches to unlock the liftgate. There are several ways to open and close the power liftgate: Press and hold on the RKE transmitter until the liftgate starts moving. Press on the overhead console inside the vehicle.
Page 13 The power window switches are located on the driver door. In addition, each passenger door has a switch for its own window. Press the switch to lower the window. Pull the switch up to raise it. For more information, see: Windows on page 3 19.
Page 14: Front Seats
If equipped, the power seat controls are located on the outboard side of the front seats. Move the seat forward or rearward by sliding the control forward or rearward. Raise or lower the front or rear part of the cushion by moving the front or rear part of the control up or down.
Page 15 If equipped, this control is located on the outboard side of the seat. On vehicles with two-way lumbar, press and hold the top of the control to increase lumbar support. To decrease, press and hold the bottom of the control. On vehicles with four-way lumbar, press and hold the front of the control to increase lumbar support.
Page 16 If equipped, this control is located on the outboard side of the seat. To recline the seatback: 1. Lift the recline lever. 2. Move the seatback to the desired position, then release the lever to lock the seatback in place. 3.
Page 17 This vehicle may have the memory package. The controls for this feature are located on the driver door, and are used to program and recall memory settings for the driver seat, outside mirrors, and the adjustable throttle and brake pedal feature. For more information, see Memory Seat, Mirrors, and Pedals on page 2 10.
Page 18: Rear Seats
On vehicles with heated front seats, or heated and cooled front seats, the controls are located on the driver and passenger doors. Press to cool the entire seat. Press to heat the seatback only. Press to heat the seat and seatback. Continue to press the desired button to cycle through the temperature settings: high (three indicator lights), medium (two indicator lights), low (one indicator light),...
Page 19: Safety Belts
Refer to the following sections for important information on how to use safety belts properly. Safety Belts: They Are for Everyone on page 2 33. How to Wear Safety Belts Properly on page 2 38. Lap-Shoulder Belt on page 2 47. Lower Anchors and Tethers for Children (LATCH) on page 2 68.
Page 20 Vehicles with manual outside mirrors can be adjusted so that the side of the vehicle and the area behind are seen. If the vehicle has towing mirrors, they can be adjusted for a clearer view of the objects behind you. Manually pull out the mirror head to extend it for better visibility when towing a trailer.
Page 21 To fold the mirrors: 1. Press (C) to fold the mirrors out to the driving position. 2. Press (D) to fold the mirrors in to the folded position. The mirrors may also include a memory function that works with the memory seats. See Memory Seat, Mirrors, and Pedals on page 2 10 for more information.
Page 22 The tilt lever is located on the lower left side of the steering column. To adjust the steering wheel: 1. Hold the steering wheel and pull the lever. 2. Move the steering wheel to a comfortable position. 3. Release the lever to lock the wheel in place. See Tilt Wheel on page 4 3.
Page 23 For vehicles with reading lamps in the overhead console, press the button located next to the lamp to turn it on or off. The vehicle may also have reading lamps in other locations. The lamps cannot be adjusted. For more information about interior lamps, see: Dome Lamps on page 4 14.
Page 24 Single wipe, turn to , then release. Several wipes, hold the band on longer. Turns the windshield wipers off. 1-18 Turn the band up for more frequent wipes or down for less frequent wipes. Slow wipes. Fast wipes. Push the paddle at the top of the lever to spray washer fluid on the windshield.
Page 25 The heating, cooling, and ventilation in the vehicle can be controlled with these systems. If this vehicle is a Two-mode Hybrid, see the Two-mode Hybrid manual for more information. A. Fan Control E. Air Conditioning B. REAR F. Driver and Passenger Temperature Controls C.
Page 26 See Climate Control System on page 4 18 and Dual Automatic Climate Control System on page 4 21. For vehicles with rear heating and air conditioning controls, see Rear Air Conditioning and Heating System on page 4 27 and Rear Air Conditioning and Heating System and Electronic Climate Controls on page 4 28.
Page 27 The transfer case knob is located next to the steering column. Use this knob to shift into and out of the different Four-Wheel Drive modes. This setting is used for driving in most street and highway situations. ideal for use when road surface traction conditions are variable.
Page 28 Press to turn the system on and off. Turn to increase or decrease the volume. Press to choose between FM, AM, or XM , if equipped. Select radio stations. Seek or scan stations. 1-22 Press to display additional text information related to the current FM-RDS or XM station;...
Page 29 To set the time and date for the radio with CD, DVD, and USB Port: 1. Turn the ignition key to ACC/ACCESSORY or ON/ RUN, then press , to turn the radio on. 2. Press to display HR, MIN, MM, DD, YYYY (hour, minute, month, day, and year).
Page 30 For vehicles with audio steering wheel controls, some audio controls can be adjusted at the steering wheel. Press to change favorite radio stations, select tracks on a CD/DVD, or to navigate tracks or folders on ® an iPod or USB device. Press to silence the vehicle speakers only.
Page 31 The vehicle's navigation system (if equipped) provides detailed maps of most major freeways and roads throughout the United States and Canada. After a destination has been set, the system provides turn-by-turn instructions for reaching the destination. In addition, the system can help locate a variety of points of interest (POI), such as banks, airports, restaurants, and more.
Page 32 This feature may alert you to vehicles located in your side blind zone. When the system detects a vehicle in the side blind zone, an amber SBZA display will light up in the corresponding outside side mirror. The system is enabled at every vehicle startup. It can be disabled through the Driver Information Center (DIC).
Page 33 Accessory power outlets can be used to connect auxiliary electrical equipment, such as a cellular telephone. There are two under the climate controls, one inside the center floor console, one on the rear of the center floor console and one accessory power outlet in the rear cargo area on the passenger side.
Page 34 There are two sunroof switches located in the overhead console above the rearview mirror. From the closed position, press the rear of the passenger side switch to vent the sunroof. To open the sunroof, press and hold the rear of the driver side switch until the sunroof reaches the desired position.
Page 35 This vehicle may have a Tire Pressure Monitor System (TPMS). The TPMS warming light alerts you to a significant loss in pressure of one of the vehicles tires. If the warning light comes on, stop as soon as possible and inflate the tires to the recommended pressure shown on the tire loading information label.
Page 36 1-30 U.S.: TTY Users: Canada: As the owner of a new Chevrolet, you are automatically enrolled in the Roadside Assistance program. This program provides technically trained advisors who are available 24 hours a day, 365 days a year, minor repair information or towing arrangements.
Page 37 ® OnStar uses several innovative technologies and live advisors to provide a wide range of safety, security, navigation, diagnostics, and calling services. In a crash, built in sensors can automatically alert an OnStar advisor who is immediately connected to the vehicle to see if you need help.
Page 38 The OnStar system can record and transmit vehicle information. This information is automatically sent to an OnStar call center when is pressed, or if the airbags or ACR system deploy. This information usually includes the vehicle's GPS location and, in the event of a crash, additional information regarding the crash that the vehicle was involved in (e.g.
Page 141: Table Of Contents
Section 3 Keys ..........3-3 Remote Keyless Entry (RKE) System .
Page 142: Table Of Contents
Section 3 Mirrors ..........3-54 Manual Rearview Mirror .
Page 143: Keys
Keys WARNING: Leaving children in a vehicle with the ignition key is dangerous for many reasons. Children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and children could be seriously injured or killed if caught in the path of a closing window.
Page 144: Remote Keyless Entry (Rke) System
See your dealer if a replacement key or additional key is needed. If the keys get locked in the vehicle, it may have to be damaged to get them out. Always carry a spare key. If you are locked out of the vehicle, call the Roadside Assistance Center.
Page 145: Remote Keyless Entry (Rke) System Operation
Remote Keyless Entry (RKE) System Operation The Remote Keyless Entry (RKE) transmitter functions work up to 195 feet (60 m) away from the vehicle. There are other conditions which can affect the performance of the transmitter. See Remote Keyless Entry (RKE) System on page 3 4. With Remote Start and Liftglass (Without and Power Liftgate...
Page 146 (Unlock): Press once to unlock only the driver door. is pressed again within three seconds, all remaining doors unlock. The interior lamps may come on and stay on for 20 seconds or until the ignition is turned on. If enabled through the DIC, the turn signal lamps flash twice to indicate unlocking has occurred.
Page 147: Battery Replacement
Programming Transmitters to the Vehicle Only RKE transmitters programmed to this vehicle will work. If a transmitter is lost or stolen, a replacement can be purchased and programmed through your dealer. When the replacement transmitter is programmed to this vehicle, all remaining transmitters must also be reprogrammed.
Page 148: Remote Vehicle Start
Remote Vehicle Start Your vehicle may have a remote starting feature. This feature allows you to start the engine from outside of the vehicle. It may also start up the vehicle's heating or air conditioning systems and rear window defogger. Normal operation of the system will return after the key is turned to the ON/RUN position.
Page 149: Remote Start Ready
3. If it is the first remote start since the vehicle has been driven, repeat these steps, while the engine is still running, to extend the engine running time by 10 minutes. Remote start can be extended one time. After entering the vehicle during a remote start, insert and turn the key to RUN to drive the vehicle.
Page 150: Doors And Locks
Doors and Locks Door Locks WARNING: Unlocked doors can be dangerous. Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. The chance of being thrown out of the vehicle in a crash is increased if the doors are not locked.
Page 151: Delayed Locking
Delayed Locking When locking the doors with the power lock switch and a door or the liftgate is open, the doors will lock five seconds after the last door is closed. You will hear three chimes to signal that the delayed locking feature is in use.
Page 152: Lockout Protection
To set the locks, do the following: 1. Insert the key into the security lock slot and turn it so the slot is in the horizontal position. 2. Close the door. When you want to open a rear door when the security lock is on, do the following: 1.
Page 153 Liftgate/Liftglass WARNING: It can be dangerous to drive with the liftglass or liftgate open because carbon monoxide (CO) gas can come into your vehicle. You cannot see or smell CO. It can cause unconsciousness and even death. If you must drive with the liftglass or liftgate open, or if electrical wiring or other cable connections must pass through the seal between the body and the liftglass or liftgate:...
Page 154 On vehicles with a liftglass, press the button on the underside of the license pocket applique (A) to open it. The liftglass can also be opened by pressing the liftglass release button on the RKE. To open the entire liftgate, press the touchpad on the underside of the liftgate handle (B).
Page 155: Power Liftgate
Power Liftgate Power Liftgate Operation WARNING: Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled.
Page 156 The taillamps will flash and a chime will sound when the power liftgate is moving. WARNING: You or others could be injured if caught in the path of the power liftgate. Make sure there is no one in the way of the liftgate as it is opening and closing.
Page 157 The power liftgate may be temporarily disabled under extreme temperatures, or under low battery conditions. If this occurs, the liftgate can still be operated manually. If you shift the transmission out of P (Park) while the power function is in progress, the liftgate power function will continue to completion.
Page 158: Power Assist Steps
Manual Operation of Power Liftgate To change the liftgate to manual operation, press the switch on the overhead console to the OFF position. With the power liftgate disabled and all of the doors unlocked, the liftgate can be manually opened and closed.
Page 159: Windows
Windows WARNING: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 160: Power Windows
Power Windows WARNING: Leaving children in a vehicle with the keys is dangerous for many reasons. Children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function and they could be seriously injured or killed if caught in the path of a closing window.
Page 161 Express-Down/Up Windows Windows with the express feature allow the windows to be raised and lowered all the way without holding the switch. Press or pull the switch fully and release it to activate the express feature. The express mode can be canceled at any time by briefly pressing or pulling the switch.
Page 162: Sun Visors
Programming the Power Windows If the battery on the vehicle has been recharged, disconnected, or is not working, you will need to reprogram each front power window for the express-up feature to work. Before reprogramming, replace or recharge the vehicle's battery. To program each front window, follow these steps: 1.
Page 163: Theft-Deterrent Systems
Theft-Deterrent Systems This vehicle has theft-deterrent features, however, they do not make it impossible to steal. Content Theft-Deterrent Your vehicle may have a content theft-deterrent alarm system. This is the security light. To arm the theft-deterrent system: 1. Open the door. 2.
Page 164: Testing The Alarm
The theft-deterrent system will not activate if the doors are locked with the vehicle's key or the manual door lock. It activates only if you use the power door lock switch with the door open or the RKE transmitter. You should also remember that you can start your vehicle with the correct ignition key if the alarm has been set off.
Page 165: Immobilizer Operation
® PASS-Key III+ Electronic Immobilizer See Radio Frequency Statement on page 8 19 for information regarding Part 15 of the Federal Communications Commission (FCC) rules and Industry Canada Standards RSS-210/220/310. ® PASS-Key III+ Electronic Immobilizer Operation ® Your vehicle has PASS-Key III+ (Personalized Automotive Security System) theft-deterrent system.
Page 166 ® It is possible for the PASS-Key the transponder value of a new or replacement key. Up to 10 keys may be programmed for the vehicle. The following procedure is for programming additional keys only. If all the currently programmed keys are lost or do not operate, you must see your dealer or a locksmith ®...
Page 167: Starting And Operating Your Vehicle
Starting and Operating Your Vehicle New Vehicle Break-In The vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: Keep your speed at 55 mph (88 km/h) or less for the first 500 miles (805 km).
Page 168 Ignition Positions The ignition switch has four different positions. To shift out of P (Park), the ignition must be in ON/RUN or ACC/ACCESSORY and the regular brake pedal must be applied. 3-28 A (LOCK/OFF): This position locks the ignition. It also locks the transmission on automatic transmission vehicles.
Page 169: Retained Accessory Power (Rap)
C (ON/RUN): This position can be used to operate the electrical accessories and to display some instrument panel cluster warning and indicator lights. The switch stays in this position when the engine is running. The transmission is also unlocked in this position on automatic transmission vehicles.
Page 170: Starting The Engine
Starting the Engine If the vehicle is a Two-mode Hybrid, see the Two-mode Hybrid manual for more information. Move the shift lever to P (Park) or N (Neutral). The engine will not start in any other position. To restart the engine when the vehicle is are already moving, use N (Neutral) only.
Page 171: Adjustable Throttle And Brake Pedal
When the engine starts, let go of the key and accelerator. If the vehicle starts briefly but then stops again, do the same thing. This clears the extra gasoline from the engine. Do not race the engine immediately after starting it. Operate the engine and transmission gently until the oil warms up and lubricates all moving parts.
Page 172: Engine Coolant Heater
Engine Coolant Heater The engine coolant heater can provide easier starting and better fuel economy during engine warm-up in cold weather conditions at or below 18°C (0°F). Vehicles with an engine heater should be plugged in at least four hours before starting. An internal thermostat in the plug-end of the cord may exist which will prevent engine coolant heater operation at temperatures above 18°C (0°F).
Page 173: Automatic Transmission Operation
Active Fuel Management Vehicles with V8 engines may have Active Fuel Management . This system allows the engine to operate on either all or half of its cylinders, depending on the driving conditions. When less power is required, such as cruising at a constant vehicle speed, the system will operate in the half cylinder mode, allowing the vehicle to achieve better fuel economy.
Page 174 Heavy Duty 6-Speed Automatic Transmission Shown (Light Duty Similar) See Range Selection Mode later in this section. P (Park): This position locks the rear wheels. It is the best position to use when starting the engine because the vehicle cannot move easily. When parked on a hill, especially when the vehicle has a heavy load, you might notice an increase in the effort to shift out of P (Park).
Page 175 WARNING: If the vehicle has a four-wheel drive transfer case with a N (Neutral) position, and the transfer case is in N (Neutral), the vehicle will be free to roll even if the shift lever is in P (Park). Be sure the transfer case is in a drive gear, Two-Wheel Drive High or Four-Wheel Drive High or Four-Wheel Drive Low...
Page 176 D (Drive): This position is for normal driving. It provides the best fuel economy. If you need more power for passing, and you are: Going less than about 35 mph (55 km/h), push the accelerator pedal about halfway down. Going about 35 mph (55 km/h) or more, push the accelerator all the way down.
Page 177 M (Manual Mode): This position is available on vehicles ® with the Hydra-Matic 6-Speed transmission. It lets drivers select the range of gears appropriate for current driving conditions. If the vehicle has this feature, see Range Select Mode (Hydra-Matic transmission) later in this section. 3 (Third): This position is also used for normal driving.
Page 178 Range Selection Mode (Hydra-Matic 6-Speed Transmission) Base trim shown (uplevel similar) The vehicle may have a Range Selection Mode. The Range Selection Mode helps control the vehicle's transmission and vehicle speed while driving down hill or towing a trailer by letting you select a desired range of gears.
Page 179: Tow/Haul Mode
While using Range Selection Mode, cruise control and the Tow/Haul mode can be used. Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transmission. The repair will not be covered by the vehicle warranty.
Page 180 When Tow/Haul mode is selected the Tow/Haul indicator light will come on. The Tow/Haul mode works with the Autoride if the vehicle has this, to enhance the ride when trailering or with a loaded vehicle. See Autoride page 5 50. Grade Braking (Hydra-Matic Automatic Transmission) The Grade Braking shift modes can be activated by...
Page 181: Front Axle
Cruise Grade Braking (Hydra-Matic 6-Speed Automatic Transmission) Cruise Grade Braking assists when driving on a downhill grade. It maintains vehicle speed by automatically implementing a shift schedule that uses the engine and the transmission to slow the vehicle. Cruise Grade Braking operates while Cruise Control is engaged in Tow/Haul mode to assist in maintaining vehicle speed under loaded vehicle conditions.
Page 182 Automatic Transfer Case The transfer case knob is located to the left of the instrument panel cluster. Use this dial to shift into and out of four-wheel drive. You can choose among five driving settings: Indicator lights in the switches show you which setting you are in.
Page 183 ® The vehicle has StabiliTrak . Shifting into Four-Wheel-Drive Low will turn Traction Control and ® ® StabiliTrak off. See StabiliTrak WARNING: Shifting the transfer case to N (Neutral) can cause the vehicle to roll even if the transmission is in P (Park).
Page 184 To shift to the Four-Wheel Drive Low position, the ignition must be in ON/RUN and the vehicle must be stopped or moving less than 3 mph (5 km/h) with the transmission in N (Neutral). The preferred method for shifting into Four-Wheel Drive Low is to have the vehicle moving 1 to 2 mph (1.6 to 3.2 km/h).
Page 185: Shifting Into Neutral
If the knob is turned to the Four-Wheel Drive High, AUTO, or Two-Wheel Drive High switch position when the vehicle is in gear and/or moving, the Four-Wheel Drive High, AUTO or Two-Wheel Drive High indicator light will flash for 30 seconds but will not complete the shift unless the vehicle is moving less than 3 mph (5 km/h) and the transmission is in N (Neutral).
Page 186 4. Release the parking brake prior to moving the vehicle. Shifting the transmission into gear before the Four-Wheel Drive Low indicator light has stopped flashing could damage the transfer case. To help avoid damaging the vehicle, always wait for the Four-Wheel Drive Low indicator light to stop flashing before shifting the transmission into gear.
Page 187 Automatic Transfer Case The transfer case knob is located to the left of the instrument panel cluster. Use this dial to shift into and out of four-wheel drive. The vehicle has Four-Wheel-Drive with StabiliTrak ® information on StabiliTrak , see StabiliTrak page 5 6.
Page 188: Parking Brake
Service Four Wheel Drive If the SERVICE 4 WHEEL DRIVE message stays on, you should take the vehicle to your dealer for service. See SERVICE 4 WHEEL DRIVE message under DIC Warnings and Messages on page 4 62. Shifting Into Four-Wheel Drive High or AUTO (Automatic Four-Wheel Drive) Turn the knob to the Four-Wheel High or AUTO position.
Page 189: Shifting Into Park
To release the parking brake, hold the regular brake pedal down, then push down momentarily on the parking brake pedal until you feel the pedal release. Slowly pull your foot up off the park brake pedal. If the parking brake is not released when you begin to drive, the brake system warning light will flash and a chime will sound warning you that the parking brake is still on.
Page 190: Torque Lock
Leaving the Vehicle With the Engine Running WARNING: It can be dangerous to leave the vehicle with the engine running. The vehicle could move suddenly if the shift lever is not fully in P (Park) with the parking brake firmly set. If you have four-wheel drive and the transfer case is in N (Neutral), the vehicle will be free to roll, even if the shift lever is in P (Park).
Page 191: Shifting Out Of Park
Shifting Out of Park This vehicle is equipped with an electronic shift lock release system. The shift lock release is designed to: Prevent ignition key removal unless the shift lever is in P (Park) with the shift lever button fully released, and Prevent movement of the shift lever out of P (Park), unless the ignition is in ON/RUN or ACC/...
Page 192: Engine Exhaust
Engine Exhaust WARNING: Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. Exposure to CO can cause unconsciousness and even death. Exhaust may enter the vehicle if: The vehicle idles in areas with poor ventilation (parking garages, tunnels, deep snow that may block underbody airflow or tail pipes).
Page 193: Running The Vehicle While Parked
Running the Vehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. WARNING: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle.
Page 194: Mirrors
Mirrors Manual Rearview Mirror Hold the inside rearview mirror in the center to move it for a clearer view behind your vehicle. Adjust the mirror to avoid glare from the headlamps behind you. Push the tab forward for daytime use and pull it for nighttime use. Automatic Dimming Rearview Mirror The vehicle may have an automatic dimming inside rearview mirror.
Page 195: Outside Power Mirrors
Outside Towing Mirrors If the vehicle has towing mirrors, they can be adjusted for a clearer view of the objects behind you. Manually pull out the mirror head to extend it for better visibility when towing a trailer. Manually fold the mirrors forward or rearward. The lower portion of the mirror is convex.
Page 196: Turn Signal Indicator
Manually fold the mirrors inward to prevent damage when going through an automatic car wash. To fold, push the mirror toward the vehicle. Push the mirror outward, to return to its original position. Outside Power Foldaway Mirrors Vehicles with outside power foldaway mirrors have the controls located on the driver door...
Page 197: Outside Automatic Dimming Mirror
Outside Automatic Dimming Mirror Vehicles with this feature have a driver outside mirror that adjusts for the glare of headlamps behind you. See Automatic Dimming Rearview Mirror on page 3 54 for more information. Park Tilt Mirrors Vehicles with the memory package have a passenger and/or driver mirror that tilts to a preselected position when the vehicle is in R (Reverse).
Page 198: Object Detection Systems
Object Detection Systems Ultrasonic Rear Parking Assist (URPA) For vehicles with the Ultrasonic Rear Parking Assist (URPA) system, it operates at speeds less than 8 km/h (5 mph), and assists the driver with parking and avoiding objects while in R (Reverse). The sensors on the rear bumper are used to detect the distance to an object up to 2.5 m (8 ft) behind the vehicle, and at least 25.4 cm (10 in) off the ground.
Page 199 The system can be disabled by pressing the rear park aid disable button located next to the radio. The indicator light will come on and PARK ASSIST OFF displays on the Driver Information Center (DIC) to indicate that URPA is off, see DIC Warnings and Messages on page 4 62.
Page 200: Side Blind Zone Alert (Sbza)
Side Blind Zone Alert (SBZA) The vehicle may have a Side Blind Zone Alert (SBZA) system. Read this entire section before using the system. WARNING: SBZA is only a lane changing aid and does not replace driver vision. SBZA does not detect: Vehicles outside the side blind zones which may be rapidly approaching.
Page 201: How The System Works
Use caution while changing lanes when towing a trailer, as the SBZA detection zones do not change when a trailer is towed. How the System Works Left Side Mirror Display Right Side Mirror Display When the vehicle is started, both outside mirror displays will briefly come on to indicate that the system is operating.
Page 202 The SBZA displays may remain on if a trailer is attached to the vehicle, or a bicycle or object is extending out to either side of the vehicle. When SBZA is disabled for any reason other than the driver turning it off, the driver will not be able to turn SBZA back on using the DIC.
Page 203: Rear Vision Camera (Rvc)
Rear Vision Camera (RVC) This vehicle may have a Rear Vision Camera system. Read this entire section before using it. WARNING: The Rear Vision Camera (RVC) system does not replace driver vision. RVC does not: Detect objects that are outside the camera's field of view, below the bumper, or underneath the vehicle.
Page 204 Vehicles With Navigation System The rear vision camera system is designed to help the driver when backing up by displaying a view of the area behind the vehicle. When the driver shifts the vehicle into R (Reverse), the video image automatically appears on the navigation screen.
Page 205 Adjusting the Brightness and Contrast of the Screen To adjust the brightness and contrast of the screen, press the MENU button while the rear vision camera image is on the display. Any adjustments made will only affect the rear vision camera screen. (Brightness) : Touch the + (plus) or screen buttons to increase or decrease the brightness of the screen.
Page 206 Rear Vision Camera Location The image is provided by the camera located above the license plate. The camera uses a special lens. The distance of the image that appears on the screen differs from the actual distance. The area displayed by the camera is limited. The camera does not display objects which are close to either corner of the bumper or under the bumper.
Page 207 When the System Does Not Seem To Work Properly The rear vision camera system might not work properly or display a clear image if: The RVC is turned off. See Turning the Rear Camera System On or Off earlier in this section. It is dark.
Page 208: Universal Home Remote System
Universal Home Remote System See Radio Frequency Statement on page 8 19 for information regarding Part 15 of the Federal Communications Commission (FCC) rules and Industry Canada Standards RSS-210/220/310. Universal Home Remote System Operation (With Three Round LED) This vehicle may have the Universal Home Remote System.
Page 209 Programming Universal Home Remote Rolling Code For questions or help programming the Universal Home Remote System, call 1-866-572-2728 or go to learcar2u.com. Most garage door openers sold after 1996 are Rolling Code units. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before starting.
Page 210 3. Immediately return to the vehicle. Press and hold the Universal Home Remote button that will be used to control the garage door until the garage door moves. The indicator light, above the selected button, should slowly blink. This button may need to be held for up to 20 seconds.
Page 211 To program up to three devices: 1. To verify that the garage door opener is a Fixed Code unit, remove the battery cover on the hand held transmitter supplied by the manufacturer of the garage door opener motor. If there are a row of dip switches similar to the graphic above, the garage door opener is a Fixed Code unit.
Page 212 Example of Eight Dip Switches with Two Positions 3-72 Example of Eight Dip Switches with Three Positions The panel of switches might not appear exactly as they do in the examples above, but they should be similar. The switch positions on the hand-held transmitter could be labeled, as follows: A switch in the up position could be labeled as Up, +, or On.
Page 213 2. Write down the eight to 12 switch settings from left to right as follows: When a switch is in the up position, write Left. When a switch is in the down position, write Right. If a switch is set between the up and down position, write Middle.
Page 214: Reprogramming Universal Home Remote Buttons
5. After entering all of the switch positions, again, firmly press and release all three buttons at the same time. The indicator lights will turn on. 6. Press and hold the button that will be used to control the garage door until the garage door moves.
Page 215: Storage Areas
Storage Areas Glove Box Lift up on the glove box lever to open it. Cupholders For vehicles with cupholders located in the front and rear of the floor console or in the fold down armrest, adjust the front cupholders by moving the insert forward or rearward.
Page 216: Center Console Storage
Center Console Storage For vehicles with a console compartment, it is located between the bucket seats. Press the button and lift the lid to access the console compartment. A cupholder located in the rear of the console, swings down for the rear seat passenger to use. Roof Rack System WARNING: If something is carried on top of the vehicle that is...
Page 217: Rear Storage Area
Do not exceed the maximum vehicle capacity when loading the vehicle. For more information on vehicle capacity and loading, see Loading the Vehicle on page 5 33. If small heavy objects are placed on the roof, cut a piece of 3/8 inch plywood to fit inside the crossrails and siderails to spread the load.
Page 218: Cargo Cover
Cargo Cover WARNING: An improperly stored cargo cover could be thrown about the vehicle during a collision or sudden maneuver. Someone could be injured. If the cover is removed, always store it in the proper storage location. When it is replaced, always be sure that it is securely reattached.
Page 219: Sunroof
Sunroof Your vehicle may be equipped with a power sliding sunroof. To open or close the sunroof, the ignition needs to be turned to ON/RUN, or Retained Accessory Power (RAP) must be active. When RAP is active, the sunroof will work for 10 minutes after the ignition is turned off, or until a front door is opened.
Page 220 The sunroof has a comfort stop feature which stops the sunroof from opening to the full-open position. From the comfort stop position, press the rear of the driver's side switch a second time to open the sunroof to the full-open position. When the sunroof is opened, an air deflector will automatically raise.
Page 221: Rear Air Conditioning And Heating System And
......4-3 Hazard Warning Flashers ..... . . 4-3 Horn .
Page 222 Tire Pressure Light ......4-39 Malfunction Indicator Lamp ....4-39 Oil Pressure Gauge .
Page 223 Press this button located on top of the steering column, to make the front and rear turn signal lamps flash on and off. This warns others that you are having trouble. Press again to turn the flashers off. When the hazard warning flashers are on, the vehicle's turn signals will not work.
Page 224 The lever on the left side of the steering column includes the following: Turn and Lane Change Signals Headlamp High/Low-Beam Changer Windshield Wipers Windshield Washer Rear Wiper Delay Rear Wiper Rear Wiper Wash Flash-to-Pass. Information for these features is on the pages following. An arrow on the instrument panel cluster flashes in the direction of...
Page 225 If the turn signal is left on for more than 3/4 of a mile (1.2 km), a chime will sound at each flash of the turn signal and the message TURN SIGNAL ON will also appear in the Driver Information Control (DIC). To turn the chime and message off, move the turn signal lever to the off position.
Page 226 Turn the band with the wiper symbol to control the windshield wipers. Single wipe, turn to Several wipes, hold the band on Turns the windshield wipers off. Turn the band up for more frequent wipes or down for less frequent wipes. Slow wipes.
Page 227 In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision. The rear wiper control is located on the turn signal/ multifunction lever. To turn the rear wiper on, slide the lever to a wiper position.
Page 228 Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use the cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control.
Page 229 If the cruise button is on when not in use, it could get bumped and go into cruise when not desired. Keep the cruise control switch off when cruise is not being used. The cruise control light on the instrument panel cluster comes on after the cruise control has been set to the desired speed.
Page 230 If the cruise control system is already activated, Press and hold the SET button on the steering wheel until the desired lower speed is reached, then release it. To slow down in small amounts, press the SET button on the steering wheel briefly. Each time this is done, the vehicle goes about 1.6 km/h (1 mph) slower.
Page 231 Parking Lamps License Plate Lamps Instrument Panel Lights The exterior lamps control has four positions: Turns off the automatic headlamps and daytime running lamps (DRL). Turning the headlamp control to the off position again turns the automatic headlamps or DRL back on. For vehicles first sold in Canada, the off position only works for vehicles that are shifted into the P (Park) position.
Page 232 Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. Fully functional daytime running lamps are required on all vehicles first sold in Canada. The DRL system comes on when the following conditions are met: The ignition is on.
Page 233 If the vehicle is started in a dark garage, the automatic headlamp system will come on immediately. Once the vehicle leaves the garage, it takes approximately one minute for the automatic headlamp system to change to DRL if it is bright enough outside. During that delay, the instrument panel cluster may not be as bright as usual.
Page 234 If the vehicle has this feature, this button includes wiring provisions for a dealer or a qualified service center to install an auxiliary roof lamp. This button is located on the overhead console. When the wiring is connected to an auxiliary roof mounted lamp, pressing the bottom of the button will activate the lamp and illuminate an indicator light at the bottom of this button.
Page 235 The dome lamp override button is located next to the exterior lamps control. Press the button in and the dome lamps remain off when a door is opened. Press the button again to return it to the extended position so that the dome lamps come on when a door is opened.
Page 236 The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all the power that is needed for very high electrical loads.
Page 237 Certain accessory plugs may not be compatible to the accessory power outlet and could result in blown adapter or vehicle fuses. If you experience a problem, see your dealer for additional information on the accessory power plugs. When adding electrical equipment, be sure to follow the proper installation instructions included with the equipment.
Page 238 The heating, cooling, and ventilation in the vehicle can be controlled with this system. A. Fan Control E. Air Conditioning B. REAR F. Driver and Passenger Temperature Controls C. Recirculation G. Rear Window D. Air Delivery Mode Defogger Control 4-18 Move the thumbwheels up or down to increase or decrease the temperature on the driver's side or the passenger side of the vehicle for the...
Page 239 Air is directed to the floor outlets, with some of the air directed to the windshield, side window, and second row floor outlets. In this mode, the system automatically selects outside air. Recirculation cannot be selected when in Floor Mode. The defog mode is used to clear the windows of fog or moisture.
Page 240 The recirculation mode cannot be used with floor, defrost, or defogging modes. If recirculation is selected while in one of those modes, the indicator flashes three times and turns off. The air conditioning compressor will also come on when this mode is activated. While in recirculation mode the windows may fog when the weather is cold and damp.
Page 241 The heating, cooling, and ventilation in the vehicle can be controlled with this system. The vehicle also has a flow-through ventilation system described later in this section. If this vehicle is a Two-mode Hybrid, see the Two-mode Hybrid manual for more information. A.
Page 242 The driver and passenger side temperature buttons are used to adjust the temperature of the air coming through the system on the driver or passenger's side of the vehicle. The temperature can be adjusted even if the system is turned off. This is possible since outside air always flows through the system as the vehicle is moving forward unless it is set to recirculation mode.
Page 243 2. Set the driver's and passenger's temperature. To find your comfort setting, start with a 23°C (74°F) temperature setting and allow about 20 minutes for the system to regulate. Use the driver's or passenger's temperature buttons to adjust the temperature setting as necessary. If a temperature setting of 15°C (60°F) is chosen, the system remains at the maximum cooling setting.
Page 244 Air is directed to the floor outlets, with some to the windshield, side window outlets, and second row floor outlets. In this mode, the system automatically selects outside air. This mode clears the windows of fog or moisture. Air is directed to the windshield, floor outlets, and side window vents.
Page 245 Press to turn the recirculation mode on or off. An indicator light comes on to show that the recirculation is on. This mode recirculates and helps to quickly cool the air inside the vehicle. It can be used to help prevent outside air and odors from entering the vehicle.
Page 246 The solar sensor, located in the defrost grille in the middle of the instrument panel, monitors the solar heat. Do not cover the solar sensor or the system will not work properly. 4-26 The interior temperature sensors located in the headliner above the driver side seat and if equipped, in the headliner above the second row seats measure the temperature of the air inside the vehicle.
Page 247 Use the air outlets located in the center and on the side of the instrument panel to direct the airflow. Keep the hood and front air inlets free of ice, snow, or any other obstruction (such as leaves). The heater and defroster will work far better, reducing the chance of fogging the inside of the windows.
Page 248 Automatic Climate Control System on page 4 21. The rear system can also be turned off by turning the rear fan knob to the position. This mode matches the rear climate control to the front climate control airflow settings. It comes on when REAR is pressed the first time. This mode directs rear seating airflow according to the settings of the rear controls.
Page 249 Press the REAR button on the front climate control system to turn the rear climate control system on or off. An indicator comes on when the rear system is on. The rear climate control system can also be turned off by pressing and holding the button.
Page 250 Warning lights and gauges can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to the warning lights and gauges could prevent injury. Warning lights come on when there might be or there is a problem with one of the vehicle's functions.
Page 251 For vehicles with a Two-mode Hybrid, see the Two-mode Hybrid manual for more information. 4-31...
Page 252 The speedometer shows the vehicle's speed in both kilometers per hour (km/h) and miles per hour (mph). The odometer shows how far the vehicle has been driven, in either kilometers (used in Canada) or miles (used in the United States). The trip odometer can show how far the vehicle has been driven since the trip odometer was last set to zero.
Page 253 console, comes on and stays on for several seconds, flashes for several more seconds and then comes on solid for several more. This chime and light sequence is repeated if the passenger remains unbuckled and the vehicle is in motion. If the passenger safety belt is buckled, neither the chime nor the light comes on.
Page 254 If the vehicle has the airbag status indicator pictured in the following illustration, then the vehicle has a passenger sensing system for the right front passenger position. The passenger airbag status indicator is on the overhead console. See Passenger Sensing System on page 2 94 for important safety information.
Page 255 This light comes on briefly when the ignition key is turned to START, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer. The light should go out once the engine starts. If it stays on, or comes on while driving, there could be a problem with the charging system.
Page 256 Readings in the low warning zone may occur when a large number of electrical accessories are operating in the vehicle and the engine is left at an idle for an extended period. This condition is normal since the charging system is not able to provide full power at engine idle.
Page 257 The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service.
Page 258 For vehicles with the StabiliTrak light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. If the system is working normally the indicator light then goes off. If the light comes on and stays on while driving, there could be a problem with the StabiliTrak vehicle might need service.
Page 259 For vehicles with a tire pressure monitoring system, this light comes on briefly when the engine is started. It provides information about tire pressures and the Tire Pressure Monitoring System. This indicates that one or more of the tires is significantly underinflated.
Page 260 This light should come on when the ignition is on, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer. If the check engine light comes on and stays on, while the engine is running, this indicates that there is an OBD II problem and service is required.
Page 261 If the light continues to flash, when it is safe to do so, stop the vehicle. Find a safe place to park the vehicle. Turn the vehicle off, wait at least 10 seconds, and restart the engine. If the light is still flashing, follow the previous steps and see your dealer for service as soon as possible.
Page 262 Some state/provincial and local governments may have programs to inspect the on-vehicle emission control equipment For the inspection, the emission system test equipment is connected to the vehicle s Data Link Connector (DLC). The DLC is under the instrument panel to the left of the steering wheel.
Page 263 The oil pressure gauge shows the engine oil pressure in psi (pounds per square inch) when the engine is running. Canadian vehicles indicate pressure in kPa (kilopascals). Oil pressure may vary with engine speed, outside temperature and oil viscosity, but readings above the low pressure zone indicate the normal operating range.
Page 264 Do not keep driving if the oil pressure is low. The engine can become so hot that it catches fire. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced. 4-44 This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer.
Page 265 The fog lamp light comes on when the fog lamps are in use. The light goes out when the fog lamps are turned off. See Fog Lamps on page 4 13 for more information. The cruise control light comes on whenever the cruise control is set.
Page 266 The fuel gauge, when the ignition is on, shows how much fuel the vehicle has left in the tank. An arrow on the fuel gauge indicates the side of the vehicle the fuel door is on. The gauge first indicates empty before the vehicle is out of fuel, and the vehicle's fuel tank should be filled soon.
Page 267 This light, under the fuel gauge, comes on briefly while the engine is being started. This light and a chime comes on when the fuel tank is low on fuel. The Driver Information Center also displays a FUEL LEVEL LOW message. See DIC Warnings and Messages on page 4 62 for more information.
Page 268 If your vehicle has DIC buttons, the information below explains the operation of this system. The DIC has different displays which can be accessed by pressing the DIC buttons located on the instrument panel, next to the steering wheel. The DIC displays trip, fuel, and vehicle system information, and warning messages if a system problem is detected.
Page 269 Press this button to display the oil life, units, side blind zone system on/off, tire pressure readings for vehicles with the Tire Pressure Monitor System (TPMS), trailer brake gain and output information for vehicles with the Integrated Trailer Brake Control (ITBC) system, engine hours, Remote Keyless Entry (RKE) transmitter programming, compass zone setting, and compass recalibration.
Page 270 Press the trip/fuel button until FUEL RANGE displays. This display shows the approximate number of remaining miles (mi) or kilometers (km) the vehicle can be driven without refueling. The display will show LOW if the fuel level is low. The fuel range estimate is based on an average of the vehicle's fuel economy over recent driving history and the amount of fuel remaining in the fuel tank.
Page 271: Maintenance Schedule
Press the trip/fuel button until TRANS TEMP displays. This display shows the temperature of the automatic transmission fluid in either degrees Fahrenheit (°F) or degrees Celsius (°C). If your vehicle has this display, press the trip/fuel button until INST ECON V8 displays. This display shows the current fuel economy at a particular moment and will change frequently as driving conditions change.
Page 272 Remember, you must reset the OIL LIFE display yourself after each oil change. It will not reset itself. Also, be careful not to reset the OIL LIFE display accidentally at any time other than when the oil has just been changed. It cannot be reset accurately until the next oil change.
Page 273 TRAILER GAIN shows the trailer gain setting. This setting can be adjusted from 0.0 to 10.0 with either a trailer connected or disconnected. To adjust this setting, see Integrated Trailer Brake Control System under Towing a Trailer on page 5 50 for more information. OUTPUT shows the power output to the trailer anytime a trailer with electric brakes is connected.
Page 274 This display allows for setting the compass zone. See DIC Compass on page 4 59 This display allows for calibrating the compass. See DIC Compass on page 4 59 This display shows no information. Use the trip odometer reset stem to view the odometer and trip odometer.
Page 275 This display allows you to select the language in which the DIC messages will appear. To select a language: 1. Press the trip odometer reset stem until ODOMETER displays. 2. While in the ODOMETER display, press and hold the trip odometer reset stem for three seconds until the currently set language displays.
Page 276 This display allows you to select the language in which the DIC messages will appear. To select a language: 1. Press the trip odometer reset stem until ODOMETER displays. 2. While in the ODOMETER display, press and hold the trip odometer reset stem for three seconds until the currently set language displays.
Page 277 Press the trip odometer reset stem until TRANS TEMP displays. This display shows the temperature of the automatic transmission fluid in either degrees Fahrenheit (°F) or degrees Celsius (°C). On vehicles with the Integrated Trailer Brake Control (ITBC) system, the trailer brake display appears in the DIC.
Page 278 When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See CHANGE ENGINE OIL SOON under DIC Warnings and Messages on page 4 62. You should change the oil as soon as you can. See Engine Oil on page 6 17.
Page 279 To match an RKE transmitter to your vehicle: 1. Press the trip odometer reset stem until RELEARN REMOTE KEY displays. 2. Press and hold the trip odometer reset stem for three seconds. The message REMOTE KEY LEARNING ACTIVE will display. 3.
Page 280 To adjust for compass variance, use the following procedure: 1. Do not set the compass zone when the vehicle is moving. Only set it when the vehicle is in P (Park). Press the vehicle information button until PRESS TO CHANGE COMPASS ZONE displays. Or, if the vehicle does not have DIC buttons, press the trip odometer reset stem until CHANGE COMPASS ZONE displays.
Page 281 4. Press the trip/fuel button until the vehicle heading, for example, N for North, is displayed in the DIC. Or, if the vehicle does not have DIC buttons, press and hold the trip odometer reset stem for two seconds to select the next available variance zone.
Page 282 Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. Multiple messages may appear one after another. Some messages may not require immediate action, but you can press any of the DIC buttons on the instrument panel or the trip odometer reset stem on the instrument panel cluster to acknowledge that you received the...
Page 283 On vehicles with the Integrated Trailer Brake Control (ITBC) system, this message may display and a chime may sound when one of the following conditions exists: A trailer with electric brakes becomes disconnected from the vehicle. If the disconnect occurs while the vehicle is stopped, this message clears itself after a short time.
Page 284 This message displays when the engine coolant temperature is too hot. Stop and allow the vehicle to idle until it cools down. See Engine Coolant Temperature Gauge on page 4 38. See Overheated Engine Protection Operating Mode on page 6 39 for information on driving to a safe place in an emergency.
Page 285 This message displays when ice conditions are possible. This message displays and a chime sounds if the driver side rear door is not fully closed and the vehicle is shifted out of P (Park). Stop and turn off the vehicle, check the door for obstructions, and close the door again.
Page 286 This message displays and a chime sounds if the liftgate or liftglass is open while the ignition is in ON/ RUN. Turn off the vehicle and check the liftgate and liftglass. Restart the vehicle and check for the message on the DIC display. This message displays while you are matching a Remote Keyless Entry (RKE) transmitter to your vehicle.
Page 287 On some vehicles, this message displays if there is a problem with the battery charging system. Under certain conditions, the charging system light may also turn on in the instrument panel cluster. See Charging System Light on page 4 35. Driving with this problem could drain the battery.
Page 288 ® If your vehicle has StabiliTrak and this message displays, it means there may be a problem with the StabiliTrak system. If you see this message, try to reset the system. Stop; turn off the engine for at least 15 seconds; then start the engine again. If this message still comes on, it means there is a problem.
Page 289 On vehicles with the Integrated Trailer Brake Control (ITBC) system, this message displays and a chime sounds when there is a problem with the ITBC system. When this message displays, power is no longer available to the trailer brakes. As soon as it is safe to do so, carefully pull your vehicle over to the side of the road and turn the ignition off.
Page 290 There are several conditions that can cause this message to appear. One condition is overheating, which could occur if StabiliTrak activates continuously for an extended period of time. The message also displays if the brake system warning light is on. See Brake System Warning Light on page 4 36.
Page 291 On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the pressure in one or more of the vehicle's tires needs to be checked. This message also displays LEFT FRT (left front), RIGHT FRT (right front), LEFT RR (left rear), or RIGHT RR (right rear) to indicate the location of the low tire.
Page 292 This message displays along with a sound if the transmission fluid in the vehicle gets hot. Driving with the transmission fluid temperature high can cause damage to the vehicle. Stop the vehicle and let it idle to allow the transmission to cool. This message clears and the chime stops when the fluid temperature reaches a safe level.
Page 293 Your vehicle may have customization capabilities that allow you to program certain features to one preferred setting. Customization features can only be programmed to one setting on the vehicle and cannot be programmed to a preferred setting for two different drivers.
Page 294 This feature allows you to select the language in which the DIC messages will appear. Press the customization button until the DISPLAY LANGUAGE screen appears on the DIC display. Press the set/reset button once to access the settings for this feature.
Page 295 This feature allows you to select whether or not to turn off the automatic door unlocking feature. It also allows you to select which doors and when the doors will automatically unlock. See Programmable Automatic Door Locks on page 3 11 for more information. Press the customization button until AUTO DOOR UNLOCK appears on the DIC display.
Page 296 No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. This feature allows you to select the type of feedback you will receive when unlocking the vehicle with the Remote Keyless Entry (RKE) transmitter.
Page 297 This feature allows you to select the amount of time you want the exterior lamps to remain on when it is dark enough outside. This happens after the key is turned from ON/RUN to LOCK/OFF. Press the customization button until EXIT LIGHTING appears on the DIC display.
Page 298 This feature allows you to select the volume level of the chime. Press the customization button until CHIME VOLUME appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: The chime volume will be set to a normal level.
Page 299 If your vehicle has this feature, it allows you to select your preference for the automatic easy exit seat feature. See Memory Seat, Mirrors, and Pedals on page 2 10 for more information. Press the customization button until EASY EXIT RECALL appears on the DIC display.
Page 300 If your vehicle has this feature, it allows you to select your preference for the remote memory seat recall feature. See Memory Seat, Mirrors, and Pedals on page 2 10 for more information. Press the customization button until MEMORY SEAT RECALL appears on the DIC display.
Page 301 This feature allows you to set all of the customization features back to their factory default settings. Press the customization button until FACTORY SETTINGS appears on the DIC display. Press the set/ reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: The customization features...
Page 302 Determine which radio the vehicle has and read the following pages to become familiar with its features. Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to entertainment tasks while driving.
Page 303 To set the time and date: 1. Turn the ignition key to ACC/ACCESSORY or ON/ RUN, then press the button to turn the radio on. 2. Press the button to display HR, MIN, MM, DD, YYYY (hour, minute, month, day, and year). 3.
Page 304 The vehicle has one of these radios as its audio system. 4-84...
Page 305 Radios with CD/MP3/DVD and USB may have a Bose Surround Sound System. Some of its features are explained later in this section under, Adjusting the Speakers (Balance/Fade) . If the vehicle has a Rear Seat Entertainment (RSE) system, it has a CD/MP3/DVD and USB radio. See Rear Seat Entertainment (RSE) System on page 4 128 The DVD player is the top slot on the radio faceplate.
Page 306 ® LTZ package and a Bose Audio System include the ® Bose AudioPilot noise compensation technology. ® When turned on, AudioPilot continuously adjusts the audio system equalization, to compensate for background noise, so that music always sounds the same at the set volume level. This feature is most effective at lower radio volume settings where background noise can affect how well the music is heard.
Page 307 Drivers are encouraged to set up their radio station favorites while the vehicle is stopped. Tune to favorite stations using the softkeys, favorites button, and steering wheel controls, if the vehicle has this feature. See Defensive Driving on page 5 2. A maximum of 36 stations can be programmed as favorites using the six softkeys below the radio station frequency tabs and by using the radio...
Page 308 adjust bass, midrange, or treble, press the the tone control tabs display. Continue pressing to highlight the desired tab, or press the softkey below the tab. Turn the knob clockwise or counterclockwise to adjust the highlighted setting. Adjust the highlighted setting by pressing either SEEK arrow, (forward), or REV (reverse) button until the desired...
Page 309 To adjust balance or fade, press the knob until the speaker control tabs display. Continue pressing to highlight the desired tab, or press the softkey under the tab. Turn the counterclockwise to adjust the highlighted setting. Adjust the highlighted setting by pressing either SEEK arrow, FWD, or REV button until the...
Page 310 Undesired XM categories can be removed through the setup menu. To remove an undesired category: 1. Press the MENU button. 2. Press the softkey below the XM CAT tab. 3. Turn the knob to display the category to be removed. 4.
Page 311 See XM Radio Messages on page 4 115 later in this section for further detail. Do not add any label to a CD. It could get caught in the CD or DVD player. If a CD is recorded on a personal computer and a description label is needed, try labeling the top of the recorded CD with a marking pen.
Page 312 Insert a CD partway into the slot, label side up. The player pulls it in and the CD should begin playing in 5 to 20 seconds for a CD, and in 30 seconds for a DVD, depending on media type and format ranges. If the ignition or radio is turned off, while a CD is in the player, it stays in the player.
Page 313 For Radios with CD/MP3/DVD and USB, press the left arrow to go to the start of the current track, if more than five seconds on the CD have played. If less than five seconds on the CD have played, the previous track plays.
Page 314 Only one audio source can be heard through the speakers at a time. An audio source is defined as DVD slot, CD slot, XM, FM/AM, Front Auxiliary Jack, or Rear Auxiliary Jack. Press the button to turn the radio on. The radio can be heard through all of the vehicle speakers.
Page 315 There are disc LOAD or disc EJECT problems. It is very hot. When the temperature returns to normal, the CD should play. The road is very rough. When the road becomes smoother, the CD should play. The CD is dirty, scratched, wet, or upside down. The air is very humid.
Page 316 Press the button on the radio to eject the disc. If a disc is ejected from the radio, but not removed, the radio reloads the disc after a short period of time. The disc is stored in the radio. The radio does not resume play of the disc automatically.
Page 317 Press to quickly reverse the CD or DVD at five times the normal speed. The radio displays the elapsed time while in fast reverse. To stop fast reversing, press again. This button might not work when the DVD is playing the copyright information or the previews.
Page 318 Once a DVD-A is inserted, radio display menu shows several tab options for DVD playing. Press the softkeys under any desired tab option during DVD playback. See the tab options listed after, for more information. The rear seat operator can navigate the DVD-A menus and controls through the remote control.
Page 319 This message displays, if no disc is present when the or DVD/CD AUX button is pressed on the radio. The radio system has an auxiliary input jack located on the lower right side of the faceplate. This is not an audio output;...
Page 320 See Using the Auxiliary Input Jack(s) later in this section, or Audio/Video (A/V) Jacks under, Rear Seat Entertainment (RSE) System on page 4 128 for more information. Radios with a USB port can control a USB storage ® device or an iPod using the radio buttons and knobs.
Page 321 The radio supports: Up to 50 folders. Up to 8 folders in depth. Up to 50 playlists. Up to 255 files. Playlists with an .m3u or .wpl extension. Files with an .mp3, .wma, or .cda file extension. The radio supports: Up to 700 folders.
Page 322 The song name that displays is the song name that is contained in the ID3 tag. If the song name is not present in the ID3 tag, then the radio displays the file name without the extension (such as .mp3) as the track name.
Page 323 Press the softkey below to go to the first track in the previous folder. Press the softkey below go to the first track in the next folder. MP3 files on the CD-R or CD-RW can be listened to in random, rather than sequential order. To use random, press the softkey under the RDM tab.
Page 324 The USB Port can be used to control an iPod or a USB storage device. To connect a USB storage device, connect the device to the USB port located on the instrument panel or in the center console. To connect an iPod, connect one end of the USB cable that came with the iPod to the iPod s dock connector and connect the other end to the USB port located in the center console.
Page 325 The five softkeys below the radio display are used to control the functions listed below. To use the softkeys: 1. Press the first or fifth softkey below the radio display to display the functions listed below, or press the softkey below the function if it is currently displayed.
Page 326 Press the softkey below to view and select a file on an iPod, using the iPod's menu system. Files are sorted by: Playlists Artists Albums Genres Songs Composers To select files: 1. Press the softkey below 2. Turn to scroll through the list of menus. 3.
Page 327 To use Shuffle: Press the softkey below select between Shuffle Off, Shuffle All Songs/Shuffle Songs, Shuffle Album, or Shuffle Folder. Press the softkey below shuffle off. This is the default mode when a USB storage device or iPod is first connected. softkey below to shuffle all songs on the USB storage device or iPod.
Page 328 The DVD Player supports: Up to 255 folders. Up to 8 folders in depth. Up to 15 playlists. Up to 40 sessions. Playlists with an .m3u or .wpl extension. Files with an .mp3, .wma, or .cda file extension. The CD Player supports: Up to 512 files and folders.
Page 329 Folders that do not contain files are skipped, and the player advances to the next folder that contains files. When the disc contains only compressed files, the files are located under the root folder. The next and previous folder function does not function on a disc that was recorded without folders or playlists.
Page 330 Preprogrammed playlists that were created using WinAmp , MusicMatch , or Real Jukebox can be accessed, however, they cannot be edited using the radio. These playlists are treated as special folders containing compressed audio song files. Playlists that have an .m3u or .pls file extension and are stored on a USB device may be supported by the radio with a USB port.
Page 331 When the scan is finished, the disc begins playing files in order by artist. The current artist playing is shown on the second line of the display. Once all songs by that artist are played, the player moves to the next artist in alphabetical order and begins playing files by that artist.
Page 332 The radio can control a USB storage device or an iPod using the radio buttons and knobs and display song information on the radio s display. Turn to select files. Press to go to the start of the track, if more than ten seconds have played.
Page 333 Press the softkey below the contents of the current folder on the USB drive. To browse and select files: 1. Press the softkey below 2. Turn to scroll through the list of folders. 3. Press to select the folder. If there is more than one folder, repeat Steps 1 and 2 until the folder is reached.
Page 334 To skip through large lists, the five softkeys can be used to navigate in the following order: First softkey, first item in the list. Second softkey, 1% through the list each time the softkey is pressed. Third softkey, 5% through the list each time the softkey is pressed.
Page 335 or any others, can be blocked at a customer's request, by calling 1-800-852-XMXM (9696). The encryption code in the receiver is being updated, and no action is required. This process should take no longer than 30 seconds. The system is functioning correctly, but the vehicle is in a location that is blocking the XM signal.
Page 336 If this message does not clear within a short period of time, the receiver could have a fault. Consult with your dealer. If this message does not clear within a short period of time, the receiver could have a fault. Consult with your dealer. For vehicles with a navigation radio system, see the separate Navigation System manual.
Page 337 Use the buttons located on the steering wheel to operate the in vehicle Bluetooth system. See Audio Steering Wheel Controls on page 4 140 for more information. Press to answer incoming calls, to confirm system information, and to start speech recognition.
Page 338 1. Press and hold for two seconds. The system responds with Ready followed by a tone. 2. Say Bluetooth . The system responds with Bluetooth ready followed by a tone. 3. Say Pair . The system responds with instructions and a four digit PIN number. The PIN number will be used in Step 4.
Page 339 1. Press and hold for two seconds. The system responds with Ready followed by a tone. 2. Say Bluetooth . The system responds with Bluetooth ready followed by a tone. 3. Say Delete . The system asks which phone to delete followed by a tone.
Page 340 The system can store up to thirty phone numbers as name tags that are shared between the Bluetooth and OnStar systems. The system uses the following commands to store and retrieve phone numbers: Store Digit Store Directory The store command allows a phone number to be stored without entering the digits individually.
Page 341 The digit store command allows a phone number to be stored by entering the digits individually. 1. Press and hold for two seconds. The system responds with Ready followed by a tone. 2. Say Digit Store . The system responds with Please say the first digit to store followed by a tone.
Page 342 The system uses the following commands to delete name tags: Delete Delete all name tags The delete command allows specific name tags to be deleted. To use the delete command: 1. Press and hold for two seconds. The system responds with Ready followed by a tone. 2.
Page 343 1. Press and hold for two seconds. The system responds with Ready followed by a tone. 2. Say Dial . The system responds with Dial using <phone name> . Number please followed by a tone. 3. Say the entire number without pausing. If the system recognizes the number, it responds with OK, Dialing and dials the number.
Page 344 1. Press and hold for two seconds. The system responds with Ready followed by a tone. 2. Say Call . The system responds with Call using <phone name>. Please say the name tag followed by a tone. 3. Say the name tag of the person to call. If the system clearly recognizes the name tag it responds with OK, calling, <name tag>...
Page 345 Call waiting must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. Press to answer an incoming call when another call is active. The original call is placed on hold. Press again to return to the original call. To ignore the incoming call, continue with the original call with no action.
Page 346 Audio can be transferred between the in vehicle Bluetooth system and the cell phone. During a call with the audio in the vehicle: 1. Press . The system responds with Ready followed by a tone. 2. Say Transfer Call. The system responds with Transferring call and the audio will switch from the vehicle to the cell phone.
Page 347 1. Press . The system responds with Ready followed by a tone. 2. Say Dial . The system responds with Say a number to send tones followed by a tone. 3. Say the number to send. If the system clearly recognizes the number it responds with OK, Sending Number and the dial tones are sent and the call continues.
Page 348 Unless information is deleted out of the in vehicle Bluetooth system, it will be retained indefinitely. This includes all saved name tags in the phonebook and phone pairing information. For information on how to delete this information, see the above sections on Deleting a Paired Phone and Deleting Name Tags.
Page 349 The RSE system may have a Parental Control feature, depending on which radio the vehicle has. To enable Parental Control, press and hold the radio power button for more than two seconds to stop all system features such as: radio, video screen, RSA, DVD and/or CD. While Parental Control is on, a padlock icon displays.
Page 350 Infrared transmitters are located at the rear of the RSE overhead console. The headphones shut off automatically to save the battery power if the RSE system and RSA are shut off or if the headphones are out of range of the transmitters for more than three minutes.
Page 351 The A/V jacks, located on the rear of the floor console, allow audio or video signals to be connected from an auxiliary device such as a camcorder or a video game unit to the RSE system. Adapter connectors or cables (not included) might be required to connect the auxiliary device to the A/V jacks.
Page 352 Audio from the DVD player or auxiliary inputs can be heard through the following possible sources: Wireless Headphones Vehicle Speakers Vehicle wired headphone jacks on the rear seat audio system, if the vehicle has this feature. The RSE system always transmits the audio signal to the wireless headphones, if there is audio available.
Page 353 To use the remote control, aim it at the transmitter window at the rear of the overhead console and press the desired button. Direct sunlight or very bright light could affect the ability of the RSE transmitter to receive signals from the remote control. If the remote control does not seem to be working, the batteries might need to be replaced.
Page 354 Press this button to exit the current active menu and return to the previous menu. This button operates only when the display menu or a DVD menu is active. Press this button to stop playing, fast reversing, or fast forwarding a DVD. Press this button twice to return to the beginning of the DVD.
Page 355 Press this button to turn ON/OFF subtitles and to move through subtitle options when a DVD is playing. The format and content of this function vary for each disc. Press this button to switch the system between the DVD player and an auxiliary source. Press this button to change camera angles on DVDs that have this feature when a DVD is playing.
Page 356 No power. The ignition might not be turned ON/RUN or in ACC/ ACCESSORY. The picture does not fill the Check the display mode screen. There are black settings in the setup menu borders on the top and by pressing the display bottom or on both sides or menu button on the remote it looks stretched out.
Page 357 I lost the remote and/or the See your dealer for headphones. assistance. The DVD is playing, but Check that the RSE video there is no picture or screen is sourced to the sound. DVD player. The DVD display error message depends on which radio is in the vehicle.
Page 358 Vehicles with this feature allow the rear seat passengers to listen to and control any of the music sources: radio, CDs, DVDs, or other auxiliary sources. However, the rear seat passengers can only control the music sources the front seat passengers are not listening to (except on some radios where dual control is allowed).
Page 359 Press this button to switch between the radio (AM/FM), XM (if equipped), CD, and if the vehicle has these features, DVD, front auxiliary, and rear auxiliary. When listening to FM, AM, or XM (if equipped), press the left or right to the previous or to the next station or channel and stay there.
Page 360 ® THEFTLOCK is designed to discourage theft of the vehicle's radio by learning a portion of the Vehicle Identification Number (VIN). The radio does not operate if it is stolen or moved to a different vehicle. Vehicles with audio steering wheel controls could differ depending on the vehicle's options.
Page 361 1. Press and hold while listening to a song until the contents of the current folder display on the radio display. 2. Press and hold to go back to the previous folder list. 3. Press and release the list. To select a folder, press and hold press when the folder is highlighted.
Page 362 between the radio, CD, and for vehicles with, DVD, front auxiliary, and rear auxiliary. For vehicles with the navigation system, press and hold this button for longer than one second to initiate voice recognition. See Voice Recognition in the Navigation System manual for more information.
Page 363 XM Satellite Radio Service gives digital radio reception from coast-to-coast in the 48 contiguous United States, and in Canada. Just as with FM, tall buildings or hills can interfere with satellite radio signals, causing the sound to fade in and out. In addition, traveling or standing under heavy foliage, bridges, garages, or tunnels may cause loss of the XM signal for a period of time.
Page 364 4-144...
Page 365 Defensive Driving ....... 5-2 Drunk Driving ........5-2 Control of a Vehicle .
Page 366 Defensive driving means always expect the unexpected. The first step in driving defensively is to wear your safety belt See Safety Belts: They Are for Everyone on page 2 33. Assume that other road users (pedestrians, bicyclists, and other drivers) are going to be careless and make mistakes.
Page 367 Police records show that almost 40 percent of all motor vehicle-related deaths involve alcohol. In most cases, these deaths are the result of someone who was drinking and driving. In recent years, more than 17,000 annual motor vehicle-related deaths have been associated with the use of alcohol, with about 250,000 people injured.
Page 368 If the vehicle is a Two mode Hybrid, see the Two mode Hybrid manual for more information. See Brake System Warning Light on page 4 36. Braking action involves perception time and reaction time. Deciding to push the brake pedal is perception time.
Page 369 This vehicle has the Antilock Brake System (ABS), an advanced electronic braking system that helps prevent a braking skid. When the engine is started and the vehicle begins to drive away, ABS checks itself. A momentary motor or clicking noise might be heard while this test is going on. This is normal.
Page 370 ABS allows the driver to steer and brake at the same time. In many emergencies, steering can help more than even the very best braking. This vehicle has a Brake Assist feature designed to assist the driver in stopping or decreasing vehicle speed in emergency driving conditions.
Page 371 If the system fails to turn on or activate, the StabiliTrak light along with one of the following messages will be displayed on the Driver Information Center (DIC): TRACTION CONTROL OFF, SERVICE TRACTION CONTROL, STABILITRAK OFF, SERVICE STABILITRAK. If these DIC messages appear, make sure the StabiliTrak system has not been turned off using the StabiliTrak on/off button.
Page 372 It is recommended to leave the system on for normal driving conditions, but it may be necessary to turn the system off if the vehicle is stuck in sand, mud, ice or snow, and you want to rock the vehicle to attempt to free it.
Page 373 Vehicles with a locking rear axle can give more traction on snow, mud, ice, sand or gravel. It works like a standard axle most of the time, but when traction is low, this feature will allow the rear wheel with the most traction to move the vehicle.
Page 374 There are times when steering can be more effective than braking. For example, you come over a hill and find a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Page 375 The vehicle's right wheels can drop off the edge of a road onto the shoulder while driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that the vehicle straddles the edge of the pavement.
Page 376 In a skid, a driver can lose control of the vehicle. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not overdriving those conditions. But skids are always possible. The three types of skids correspond to the vehicle's three control systems.
Page 377 Vehicles with four-wheel drive can be used for off-road driving. Vehicles without four-wheel drive and vehicles with 20 inch tire/wheel assemblies should not be driven off-road except on a level, solid surface. The airbag system is designed to work properly under a wide range of conditions, including off road usage.
Page 378 If you think you will need some more ground clearance at the front of your vehicle, you can remove the front fascia lower air dam. The air dam is held in place by two bolts and 10 snaps accessible from underneath the front fascia.
Page 379 The heaviest things should be on the floor, forward of the rear axle. Put heavier items as far forward as you can. Be sure the load is properly secured, so things are not tossed around. You will find other important information under Loading the Vehicle on page 5 33 and Tires on page 6 63.
Page 380 It is a good idea to practice in an area that is safe and close to home before you go into the wilderness. Off-roading requires some new and different skills. Tune your senses to different kinds of signals. Your eyes need to constantly sweep the terrain for unexpected obstacles.
Page 381 Unseen or hidden obstacles can be hazardous. A rock, log, hole, rut, or bump can startle you if you are not prepared for them. Often these obstacles are hidden by grass, bushes, snow, or even the rise and fall of the terrain itself. Some things to consider: Is the path ahead clear? Will the surface texture change abruptly up ahead?
Page 382 When you approach a hill, decide if it is too steep to climb, descend, or cross. Steepness can be hard to judge. On a very small hill, for example, there may be a smooth, constant incline with only a small change in elevation where you can easily see all the way to the top.
Page 383 Sound the horn as you approach the top of the hill to let opposing traffic know you are there. Use headlamps even during the day to make the vehicle more visible to oncoming traffic. Driving to the top (crest) of a hill at full speed can cause an accident.
Page 384 If, after stalling, you try to back down the hill and decide you just cannot do it, set the parking brake, put your transmission in P (Park), and turn off the engine. Leave the vehicle and go get some help. Exit on the uphill side and stay clear of the path the vehicle would take if it rolled downhill.
Page 385 Heavy braking when going down a hill can cause your brakes to overheat and fade. This could cause loss of control and a serious accident. Apply the brakes lightly when descending a hill and use a low gear to keep vehicle speed under control.
Page 386 An off-road trail will probably go across the incline of a hill. To decide whether to try to drive across the incline, consider the following: Driving across an incline that is too steep will make your vehicle roll over. You could be seriously injured or killed.
Page 387 Getting out on the downhill (low) side of a vehicle stopped across an incline is dangerous. If the vehicle rolls over, you could be crushed or killed. Always get out on the uphill (high) side of the vehicle and stay well clear of the rollover path. If the vehicle stalls when crossing an incline, be sure you, and any passengers, get out on the uphill side, even if the door there is harder to open.
Page 388 Driving through rushing water can be dangerous. Deep water can sweep your vehicle downstream and you and your passengers could drown. If it is only shallow water, it can still wash away the ground from under your tires, and you could lose traction and roll the vehicle over.
Page 389 Night driving is more dangerous than day driving because some drivers are likely to be impaired alcohol or drugs, with night vision problems, or by fatigue. Night driving tips include: Drive defensively. Do not drink and drive. Reduce headlamp glare by adjusting the inside rearview mirror.
Page 390 Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate. Always drive slower in these types of driving conditions and avoid driving through large puddles and deep standing or flowing water. Wet brakes can cause crashes. They might not work as well in a quick stop and could cause pulling to one side.
Page 391 To prepare your vehicle for a long trip, consider having it serviced by your dealer before departing. Things to check on your own include: Windshield Washer Fluid: Reservoir full? Windows clean inside and outside? Wiper Blades: In good shape? Fuel, Engine Oil, Other Fluids: All levels checked? Lamps: Do they all work and are lenses clean? Tires: Are treads good? Are tires inflated to recommended pressure?
Page 392 Driving on steep hills or through mountains is different than driving on flat or rolling terrain. Tips for driving in these conditions include: Keep the vehicle serviced and in good shape. Check all fluid levels and brakes, tires, cooling system, and transmission. Going down steep or long hills, shift to a lower gear.
Page 393 Drive carefully when there is snow or ice between the tires and the road, creating less traction or grip. Wet ice can occur at about 0°C (32°F) when freezing rain begins to fall, resulting in even less traction. Avoid driving on wet ice or in freezing rain until roads can be treated with salt or sand.
Page 394 Being stuck in snow can be in a serious situation. Stay with the vehicle unless there is help nearby. If possible, use the Roadside Assistance Program on page 8 7. To get help and keep everyone in the vehicle safe: Turn on the Hazard Warning Flashers on page 4 3.
Page 395 To save fuel, run the engine for only short periods as needed to warm the vehicle and then shut the engine off and close the window most of the way to save heat. Repeat this until help arrives but only when you feel really uncomfortable from the cold.
Page 396 Turn the steering wheel left and right to clear the area around the front wheels. For four-wheel-drive vehicles, shift into Four Wheel High or, if the vehicle has a two speed automatic transfer case, Four Wheel Low. ® For vehicles with StabiliTrak , turn the traction control part of the system off.
Page 397 For vehicles with recovery hooks at the front of the vehicle, you can use them if you are stuck off-road and need to be pulled to some place where you can continue driving. It is very important to know how much weight your vehicle can carry.
Page 398 A vehicle specific Tire and Loading Information label is attached to the center pillar (B-pillar). With the driver's door open, you will find the label attached below the door lock post (striker). The tire and loading information label shows the number of occupant seating positions (A), and the maximum vehicle capacity weight (B) in kilograms and pounds.
Page 399 The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the XXX amount equals 1400 lbs and there will be five 150 lb passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (1400 750 (5 x 150) = 650 lbs).
Page 400 Vehicle Capacity Weight for Example 2 = Subtract Occupant Weight @ 150 lbs (68 kg) × 5 = Available Cargo Weight = 5-36 1,000 lbs (453 kg) 750 lbs (136 kg) 250 lbs (113 kg) Vehicle Capacity 1,000 lbs Weight for (453 kg) Example 3 = Subtract Occupant...
Page 401 Refer to your vehicle's tire and loading information label for specific information about your vehicle's capacity weight and seating positions. The combined weight of the driver, passengers, and cargo should never exceed your vehicle's capacity weight. A vehicle specific Certification/Tire label is found on the rear edge of the driver's door.
Page 402: Child Restraints
The Certification/Tire label also contains information about your Front Axle Reserve Capacity. And, if you do have a heavy load, you should spread it out. Do not load the vehicle any heavier than the Gross Vehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GAWR).
Page 403 When you carry something inside the vehicle, secure it whenever you can. Do not leave a seat folded down unless you need to. There is also important loading information for off-road driving in this manual. See Loading Your Vehicle for Off-Road Driving under Off-Road Driving on page 5 13 .
Page 404 Here are some guidelines for safely carrying a snow plow on your vehicle: Make sure the weight on the front and rear axles does not exceed the axle rating for each. For the front axle, if more cargo or passengers must be carried, appropriate counter ballast must be installed rear of the rear axle.
Page 405 In order to calculate the amount of weight any front accessory, such as a snow plow, is adding to the front axle, use the following formula: (W x (A + W.B.)) /W.B.= Weight the accessory is adding to the front axle. Where: W = Weight of added accessory A = Distance that the accessory is in front of the...
Page 406 You can add heavier equipment on the front of the vehicle if you compensate for it by carrying fewer passengers, less cargo, or by positioning cargo towards the rear. This has the effect of reducing the load on the front. However, the front GAWR, rear GAWR, and the Gross Vehicle Weight Rating (GVWR) must never be exceeded.
Page 407 Vehicles with the RPO VYU snow plow prep package also have an emergency roof lamp provision package, RPO TRW. Wiring for the emergency roof lamp is provided above the overhead console. See Auxiliary Roof-Mounted Lamp on page 4 14 for switch location. To avoid damage, the disabled vehicle should be towed with all four wheels off the ground.
Page 408 Two-wheel-drive vehicles and four-wheel drive vehicles with a single speed automatic transfer case shoul d not be towed with all four wheels on the ground. Two-wheel-drive transmissions have no provisions for internal lubrication while being towed. Four-wheel drive vehicles with a single speed automatic transfer case have no neutral position and will spin the transmission when the rear wheels turn.
Page 409 Use the following procedure to dinghy tow a four-wheel drive vehicle with a two speed automatic transfer case: 1. Position the vehicle being towed behind the tow vehicle and shift the transmission to P (Park). 2. Turn the engine off and firmly set the parking brake.
Page 410 Two-wheel-drive vehicles and four-wheel drive vehicles with a single speed automatic transfer case should not be towed with the rear wheels on the ground. Two-wheel-drive transmissions have no provisions for internal lubrication while being towed. Four-wheel drive vehicles with a single speed automatic transfer case have no neutral position and will spin the transmission when the rear wheels turn.
Page 411 Use the following procedure to dolly tow a four-wheel drive vehicle from the front: 1. Attach the dolly to the tow vehicle following the dolly manufacturer's instructions. 2. Drive the front wheels onto the dolly. 3. Shift the transmission to P (Park). 4.
Page 412 Use the following procedure to dolly tow the vehicle from the rear: 1. Attach the dolly to the tow vehicle following the dolly manufacturer's instructions. 2. Drive the rear wheels onto the dolly. 5-48 3. Firmly set the parking brake. See Parking Brake on page 3 48.
Page 413 4. Put the transmission in P (Park). 5. Secure the vehicle to the dolly following the manufacturer's instructions. 6. Use an adequate clamping device designed for towing to ensure that the front wheels are locked into the straight position. Shifting a four-wheel-drive vehicle's transfer case into N (Neutral) can cause the vehicle to roll even if the transmission is in P (Park).
Page 414 With this feature, improved vehicle ride and handling is provided under a variety of passenger and loading conditions. The system is fully automatic and uses a computer controller to continuously monitor vehicle speed, wheel to body position, lift/dive and steering position of the vehicle.
Page 415 To identify the trailering capacity of the vehicle, read the information in Weight of the Trailer that appears later in this section. Trailering is different than just driving the vehicle by itself. Trailering means changes in handling, acceleration, braking, durability and fuel economy. Successful, safe trailering takes correct equipment, and it has to be used properly.
Page 416 Important considerations that have to do with weight: The weight of the trailer The weight of the trailer tongue The weight on the vehicle's tires And the weight of the trailering combination How heavy can a trailer safely be? It depends on how the rig is used. Speed, altitude, road grades, outside temperature and how much the vehicle is used to pull a trailer are all important.
Page 417 1500 Series 4WD Short Wheel Base 5.3L V8 5.3L V8 5.3L V8 K5L HD Cooling Pkg 1500 Series 4WD Long Wheel Base 5.3L V8 5.3L V8 5.3L V8 K5L HD Cooling Pkg 6.2L V8 2500 Series 2WD Long Wheel Base 6.0L V8 2500 Series 4WD Long Wheel Base 6.0L V8...
Page 418 The tongue load (A) of any trailer is very important because it is also part of the vehicle weight. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo carried in it, and the people who will be riding in the vehicle as well as trailer tongue weight.
Page 419 Do not exceed the maximum allowable tongue weight for the vehicle. Choose the shortest hitch extension that will position the hitch ball closest to the vehicle. This will help reduce the effect of trailer tongue weight on the rear axle. Trailering may be limited by the vehicle's ability to carry tongue weight.
Page 420 Body to Ground Distance Front of Vehicle When using a weight-distributing hitch, the spring bars should be adjusted so the distance (A) is the same after coupling the trailer to the tow vehicle and adjusting the hitch. 5-56 Always attach chains between the vehicle and the trailer.
Page 421 Pressing this button at the end of the shift lever turns on and off the tow/ haul mode. This indicator light on the instrument panel cluster comes on when the tow/ haul mode is on. Tow/Haul is a feature that assists when pulling a heavy trailer or a large or heavy load.
Page 422 A loaded trailer that weighs more than 2,000 lbs (900 kg) needs to have its own brake system that is adequate for the weight of the trailer. Be sure to read and follow the instructions for the trailer brakes so they are installed, adjusted and maintained properly.
Page 423 The ITBC system is powered through the vehicle's electrical system. Turning the ignition off will also turn off the ITBC system. The ITBC system is fully functional only when the ignition is in ON or in RUN. The ITBC system can only be used with trailers with electric brakes.
Page 424 A. Manual Trailer Brake Apply Lever B. Trailer Gain Adjustment Buttons The ITBC system has a control panel located on the instrument panel to the left of the steering column. See Instrument Panel on page 1 2. The control panel allows adjustment to the amount of output, referred to as trailer gain, available to the electric trailer brakes and allows manual application the trailer brakes.
Page 425 All DIC warning and service messages must first be acknowledged by the driver by pressing the odometer trip stem or the DIC Vehicle Information button (if equipped) before the Trailer Brake Display Page can be displayed and Trailer Gain can be adjusted. TRAILER GAIN This setting is displayed anytime the Trailer Brake Display Page is active.
Page 426 The Manual Trailer Brake Apply Lever is located on the Trailer Brake Control Panel and is used to apply the trailer s electric brakes independent of the vehicle s brakes. This lever is used in the Trailer Gain Adjustment Procedure to properly adjust the power output to the trailer brakes.
Page 427 4. Adjust the Trailer Gain by using the gain adjustment (+ / -) buttons on the Trailer Brake Control Panel. 5. Drive the vehicle with the trailer attached on a level road surface representative of the towing condition and free of traffic at about 20 to 25 mph (32 to 40 km/h) and fully apply the Manual Trailer Brake Apply lever.
Page 428 2. There is an electrical fault in the wiring to the electric trailer brakes. This message will continue as long as there is an electrical fault in the trailer wiring. This message will also turn off if the driver acknowledges this message off. To determine if the electrical fault is on the vehicle side or trailer side of the trailer wiring harness connection, do the following:...
Page 429 When towing a trailer, exhaust gases may collect at the rear of the vehicle and enter if the liftgate, trunk/hatch, or rear-most window is open. Engine exhaust contains carbon monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death.
Page 430 Stay at least twice as far behind the vehicle ahead as you would when driving the vehicle without a trailer. This can help to avoid heavy braking and sudden turns. More passing distance is needed when towing a trailer. The combination will not accelerate as quickly and is longer so it is necessary to go much farther beyond the passed vehicle before returning to the lane.
Page 431 Parking the vehicle on a hill with the trailer attached can be dangerous. If something goes wrong, the rig could start to move. People can be injured, and both the vehicle and the trailer can be damaged. When possible, always park the rig on a flat surface.
Page 432 1. Apply and hold the brake pedal. 2. Start the engine 3. Shift into a gear 4. Release the parking brake 5. Let up on the brake pedal. 6. Drive slowly until the trailer is clear of the chocks. 7. Stop and have someone pick up and store the chocks.
Page 433 The vehicle is equipped with the seven-wire trailer towing harness. This harness with a seven-pin universal trailer connector is attached to a bracket on the hitch platform. The seven-wire harness contains the following trailer circuits: Yellow: Left Stop/Turn Signal Dark Green: Right Stop/Turn Signal Brown: Taillamps White: Ground Light Green: Back-up Lamps...
Page 434 These wiring provisions are included with the vehicle as part of the trailer wiring package. These provisions are for an electric brake controller. The instrument panel contains blunt cut wires near the data link connector for the trailer brake controller. The harness contains the following wires: Dark Blue: Brake Signal to Trailer Connector Red/Black: Battery...
Page 599: Airbag System
Accessories and Modifications ..... . .6-4 Accessory Power ........3-29 Accessory Power Outlets .
Page 600: Automatic Transmission
Appearance Care (cont.) Tires ..........6-115 Underbody Maintenance .
Page 601: Checking Things Under The Hood
Calibration ......... 4-59 California Perchlorate Materials Requirements .
Page 602: Customer Information
Cleaning (cont.) Washing Your Vehicle ......6-111 Weatherstrips ........6-111 Windshield, Backglass, and Wiper Blades .
Page 603: Electrical System
Driver Information Center (DIC) ....4-47 DIC Operation and Displays ....4-48, 4-55 DIC Vehicle Customization .
Page 604: Fog Lamps
Engine (cont.) Cooling System ........6-30 Drive Belt Routing .
Page 605 Fuses Center Instrument Panel Fuse Block ... . .6-120 Fuses and Circuit Breakers ..... . 6-118 Instrument Panel Fuse Block .
Page 606: Instrument Panel
Ignition Positions ........3-28 Infants and Young Children, Restraints ... . 2-59 Inflation - Tire Pressure .
Page 607: Rear Axle
Lights (cont.) Passenger Airbag Status Indicator ....4-34 Safety Belt Reminders ......4-32 Security .
Page 608 Navigation System, Privacy ......8-19 Navigation/Radio System, see Navigation Manual ......... . 4-116 New Vehicle Break-In .
Page 609 Parking Assist ..........3-58 Brake .
Page 610: Restraint System Check
Rear Axle ......... . 6-51 Locking .
Page 611: Securing A Child Restraint
Safety Belts (cont.) Reminders ........4-32 Safety Belts Are for Everyone .
Page 612 Spare Tire (cont.) Installing ......... . 6-94 Removing .
Page 613 Tires (cont.) Aluminum or Chrome-Plated Wheels, Cleaning ........6-114 Buying New Tires .
Page 614: Warning Lights, Gauges, And Indicators
Vehicle Control ..........5-3 Loading .

This manual is also suitable for:

2010 suburban 1500 2010 suburban 2500 2010 suburban

Chevrolet 2010 Tahoe Owner's Manual

Quick Links

Related Manuals for Chevrolet 2010 Tahoe

Summary of Contents for Chevrolet 2010 Tahoe

This manual is also suitable for:

Table of Contents