[Ac Voltage Monitor] - Panasonic PT-RZ12K Operating Instructions Manual

3) Press qw to switch the pages.
f The page will change each time you press the button.
[PROJECTOR TYPE]
[PROJECTOR RUNTIME]
[LIGHT RUNTIME]
[MAIN/SUB VERSION]
[INTAKE AIR TEMP.]
[OPTICS MODULE TEMP.]
[EXHAUST AIR TEMP.]
[AROUND LIGHT1 TEMP.]
[AROUND LIGHT2 TEMP.]
[COOLING CONDITION]
[ATMOSPHERIC PRESSURE] Displays the atmospheric pressure.
[SELF TEST]
[INPUT]
[BACKUP INPUT STATUS]
[SIGNAL NAME]
[SIGNAL FREQUENCY]
[NUMBER OF REGISTERED
SIGNAL]
[REMOTE2 STATUS]
[AC VOLTAGE]
[UPGRADE]
[ON COUNT]
[SIGNAL INFORMATION]
*1 The temperature status is indicated with text color (green/yellow/red) and bar scale. Use the projector within the range that the indication is
green.
Note
f Press the <ENTER> button while displaying the [STATUS] screen to send an E-mail including the content of status to the E-mail addresses
(up to two addresses) set in "[E-mail set up] page" (x page 172).
f Some items in [SIGNAL INFORMATION] may be displayed and others not displayed, depending on the signal being input.
f If any abnormality has occurred on the projector, press the <DEFAULT> button while the [STATUS] screen is displayed to display the detail
screen of the error information.
f For details on the contents displayed in [SELF TEST], refer to "Self-diagnosis display" (x page 189).

[AC VOLTAGE MONITOR]

Enable or disable the AC voltage monitor function. The value of input supply voltage is displayed on the self-
diagnosis display at the side of the projector when enabled.
1) Press as to select [AC VOLTAGE MONITOR].
Chapter 4 Settings — [PROJECTOR SETUP] menu
Displays the projector type and serial number of the projector.
Displays the runtime of the projector.
Displays the runtime of the light source 1 and the light source 2.
Displays the main and sub versions of the firmware of the projector.
Displays the status of the intake air temperature of the projector.
*1
Displays the status of the internal temperature of the projector.
*1
Displays the status of the exhaust air temperature of the projector.
*1
Displays the status of the temperature around light source 1 of the projector.
*1
Displays the status of the temperature around light source 2 of the projector.
*1
Displays the set cooling conditions. Automatically recognized result is displayed when set to [AUTO].
Displays the status of the projector.
Displays the input terminal currently selected.
Displays whether switching to the backup input signal is possible or not when [BACKUP INPUT
MODE] is set to [OFF]. (x page 110)
Displays the input signal name.
Displays the frequency of the input signal.
Displays the number of registered signals.
Displays the control status of the REMOTE2.
Displays the input supply voltage.
[ET-UK20]
[ET-CUK10]
[POWER ON TIMES]
[SHUTTER]
[MEMORY NO.]
[INPUT]
[SIGNAL NAME]
[SIGNAL FREQUENCY]
[SYNC.STATE]
[V.SYNC WIDTH]
[SCAN TYPE]
[TOTAL DOTS]
[DISPLAY DOTS]
[TOTAL LINES]
[DISPLAY LINES]
[SAMPLING]
[SIGNAL LEVEL]
[BIT DEPTH]
Displays the activation status by the Upgrade Kit (Model No.:
ET-UK20).
Displays the activation status by the Auto Screen Adjustment
Upgrade Kit (Model No.: ET-CUK10).
Displays the number of times the power is turned on.
Displays the number of times the mechanical shutter is closed.
It is counted when [MECHANICAL SHUTTER] is set to [ENABLE].
Displays the memory number of the input signal.
Displays the input terminal currently selected.
Displays the input signal name.
Displays the frequency of the input signal.
Displays the synch polarity of the input signal.
Displays the vertical sync signal pulse width of the input signal.
Displays the scan type of the input signal.
Displays the total dot count of the input signal.
Displays the number of input signal display dots.
Displays the total line count of the input signal.
Displays the number of input signal display lines.
Displays the sampling information of the input signal.
Displays the signal level of the input signal.
Displays the gradation of the input signal.
ENGLISH - 143