Table of Contents
Advertisement
2.1
Before you proceed
Take note of the following precautions before you install motherboard
components or change any motherboard settings.
•
Unplug the power cord from the wall socket before touching any
component.
•
Use a grounded wrist strap or touch a safely grounded object or a
metal object, such as the power supply case, before handling
components to avoid damaging them due to static electricity
•
Hold components by the edges to avoid touching the ICs on them.
•
Whenever you uninstall any component, place it on a grounded
antistatic pad or in the bag that came with the component.
•
B e f o r e y o u i n s t a l l o r r e m o v e a n y c o m p o n e n t , e n s u r e
B e f o r e y o u i n s t a l l o r r e m o v e a n y c o m p o n e n t , e n s u r e
B e f o r e y o u i n s t a l l o r r e m o v e a n y c o m p o n e n t , e n s u r e
B e f o r e y o u i n s t a l l o r r e m o v e a n y c o m p o n e n t , e n s u r e
B e f o r e y o u i n s t a l l o r r e m o v e a n y c o m p o n e n t , e n s u r e
t h a t t h e A T X p o w e r s u p p l y i s s w i t c h e d o f f o r t h e
t h a t t h e A T X p o w e r s u p p l y i s s w i t c h e d o f f o r t h e
t h a t t h e A T X p o w e r s u p p l y i s s w i t c h e d o f f o r t h e
t h a t t h e A T X p o w e r s u p p l y i s s w i t c h e d o f f o r t h e
t h a t t h e A T X p o w e r s u p p l y i s s w i t c h e d o f f o r t h e
p o w e r c o r d i s d e t a c h e d f r o m t h e p o w e r s u p p l y .
p o w e r c o r d i s d e t a c h e d f r o m t h e p o w e r s u p p l y .
p o w e r c o r d i s d e t a c h e d f r o m t h e p o w e r s u p p l y .
p o w e r c o r d i s d e t a c h e d f r o m t h e p o w e r s u p p l y .
p o w e r c o r d i s d e t a c h e d f r o m t h e p o w e r s u p p l y . Failure
to do so may cause severe damage to the motherboard, peripherals,
and/or components.
Onboard LED
Onboard LED
Onboard LED
Onboard LED
Onboard LED
The motherboard comes with a standby power LED that lights up to
indicate that the system is ON, in sleep mode, or in soft-off mode.
This is a reminder that you should shut down the system and unplug
the power cable before removing or plugging in any motherboard
component. The illustration below shows the location of the onboard
LED.
A8R-MVP
®
A8R-MVP Onboard LED
Make sure to connect the EZPlug when using two PCI Express graphics
cards and a 20-pin ATX power supply unit, or if the graphics cards do
not have auxiliary power plugs. See page 2-24 for the location of the
EZPlug connector.
A S U S A 8 R - M V P
A S U S A 8 R - M V P
A S U S A 8 R - M V P
A S U S A 8 R - M V P
A S U S A 8 R - M V P
SB_PWR
ON
OFF
Standby
Powered
Power
Off
2 - 1
2 - 1
2 - 1
2 - 1
2 - 1
Hide quick links:
Advertisement
Table of Contents
