1. Manuals
  2. Brands
  3. Interlogix Manuals
  4. DVR
  5. TruVision DVR 44HD
  6. User manual

Interlogix TruVision 44HD User Manual

Hide thumbs Also See for TruVision 44HD:
Table of Contents

Advertisement

Quick Links

Download this manual
TruVision DVR 44HD User
Manual
P/N 1072968-EN • REV B • ISS 11AUG15

Advertisement

Table of Contents
loading

Related Manuals for Interlogix TruVision 44HD

Summary of Contents for Interlogix TruVision 44HD

  • Page 1 TruVision DVR 44HD User Manual P/N 1072968-EN • REV B • ISS 11AUG15...
  • Page 2 Copyright © 2015 United Technologies Corporation. All rights reserved. Interlogix is part of UTC Building & Industrial Systems, a unit of United Technologies Corporation. All rights reserved. Trademarks and patents Trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.

  • Page 3: Table Of Contents

    Content Important information 5 Chapter 1 Product introduction 6 Product overview 6 Default settings to access the device 6 Chapter 2 Physical installation 8 Installation environment 8 Unpacking the recorder and its accessories 8 Back panel 9 Monitor connections 11 Rack mounting 11 Chapter 3 Getting started 12...
  • Page 4 Chapter 7 Searching files 43 Search video menu 43 Search for motion events in playback 44 Search and play back recordings by time and video type 45 Search and playback recordings by event 46 Search bookmarked recordings 47 Search snapshots 47 Log search 48 Disk analysis 48 Chapter 8...
  • Page 5 Export network packet data 87 Network statistics 87 Chapter 12 Recording 88 Recording schedule 88 Modify the instant replay duration 90 Manual recording 91 Chapter 13 Alarm and event setup 92 Set up alarm inputs 92 Set up alarm outputs 93 Manual trigger 94 Buzzer settings 95 Alarm notification types 95...
  • Page 6 Appendix C Port forwarding information 138 Seeking further assistance 138 Appendix D Connect a PTZ dome camera 140 Configuring the PTZ protocols for Interlogix cameras 140 Appendix E KTD-405 keypad 144 Supported firmware 144 Wiring the keypad 144 Setting the keypad to work with the recorder 145...

  • Page 7: Important Information

    Important information Advisory messages Advisory messages alert you to conditions or practices that can cause unwanted results. The advisory messages used in this document are shown and described below. WARNING: Warning messages advise you of hazards that could result in injury or loss of life.

  • Page 8: Product Introduction

    Chapter 1 Product introduction Product overview This recorder is a full featured and scalable digital video recording system that can store, display, search, export and manage video from up to 16 analog, HD analog, or IP cameras. The recorder utilizes HD-TVI technology to record up to 1080P resolution. HD-TVI (Transport Video Interface) is an open standard meaning it can record any camera using the TVI standard.
  • Page 9 Chapter 1: Product introduction Table 1: Default user names and passwords User Description Administrator There can only be one administrator. The user name is “admin”. The name cannot be modified. The default password is 1234. Operator The default user name is “operator”. The default password is 2222.

  • Page 10: Physical Installation

    Chapter 2 Physical installation This section describes how to install the recorder. Installation environment When installing your product, consider these factors: • Ventilation • Temperature • Moisture • Chassis load Ventilation: Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

  • Page 11: Back Panel

    Chapter 2: Physical installation • IR (infrared) remote control • Two AAA batteries for the remote control • AC power cords • USB mouse • Recorder • CD with software and manuals • TruVision DVR 44HD Quick Start Guide • TruVision DVR 44HD User Manual (on CD) •...
  • Page 12 Chapter 2: Physical installation Figure 1: TVR 44HD back panel connections (16-channel model shown) Description Specification One audio input Connect microphone for bi-directional RCA jack, 315 mV, 40 kohms. audio (not recorded) Unbalanced. Line-level audio requires amplification. One audio output Connect to speakers for audio output.

  • Page 13: Monitor Connections

    Chapter 2: Physical installation Description Specification 16 alarm inputs Connect physical alarms such as detectors, push buttons, etc. Four alarm outputs Connect physical alarm outputs such as a siren, flash, relay. Ground Connect to ground. Power cord Connect a PSU. The PSU is shipped with the recorder.

  • Page 14: Getting Started

    Chapter 3 Getting started Power on the recorder Before starting the recorder, connect at least one monitor. Otherwise, you will not be able to see the user interface and operate the device. The recorder auto-detects the video mode (PAL or NTSC) on startup. It comes equipped with a universal power supply that will auto-sense 110/240 V, 60/50 Hz.

  • Page 15: The Startup Wizard

    Chapter 3: Getting started The startup wizard The recorder has an express installation wizard that lets you easily configure basic recorder settings when first used. It configures all cameras to default settings. The configuration of each camera and recorder can be customized as required. By default the startup wizard will start once the recorder has loaded.
  • Page 16 Chapter 3: Getting started Note: You must enter an admin password. To change the Admin password, check Admin password and enter the new password and confirm it. Caution: It is strongly recommended that you change the password of the administrator. Do not leave 1234 as the default password.
  • Page 17 Chapter 3: Getting started Click Next to move to the next page, or Previous to return to the previous page. 7. HDD management: The hard drives are initialized at the factory. However if you wish to clear all data, click Initialize to initialize the HDD and Next...
  • Page 18 Chapter 3: Getting started Check the Constant Recording checkbox for the recorder to record continuously all day. If left unchecked, the recorder will not record. Check the desired time lapse check box, TL-Hi or TL-Lo. To record motion detection events, check Event (Motion).

  • Page 19: Operating Instructions

    Chapter 4 Operating instructions Controlling the recorder There are several ways to control the recorder: • Front panel control. See “Using the front panel ” below. • Mouse control. See “Using the mouse” on page 21. • IR remote control. See “Using the IR remote control” on page 22. •...
  • Page 20 Chapter 4: Operating instructions Figure 3: TVR 44HD front panel (8-channel model shown) The controls on the front panel include: Table 2: Front Panel Elements Name Description Display buttons See Table 3 on page 20 for a detailed description of all these buttons for different tasks.
  • Page 21 Chapter 4: Operating instructions Name Description Playback buttons Reverse: Press to jump back to the oldest available video and start the playback. Pause: Press to pause playback. Play: Press to start 24-hour playback of the currently selected camera. If you are in multiview format, only the camera shown in the top-left corner of the multiview is played back.
  • Page 22 Chapter 4: Operating instructions Name Description Status LEDs HDD: A steady GREEN light indicates that the recorder is accessing the HDD in read or write operation. A steady RED light indicates HDD failure. Network: A steady GREEN light indicates that the recorder is currently connected to a network.

  • Page 23: Using The Mouse

    Chapter 4: Operating instructions Task Button Button function Play Press to do an auto tour. Display Press to delete a selected key point from the PTZ Setting > More Settings> Tour > Key Point list. Menu navigation Direction Press to navigate between different fields and items in menus. Menu Enter/exit the main menu.

  • Page 24: Using The Ir Remote Control

    Chapter 4: Operating instructions Item Description Scroll Down Live view: Move to the next window. Menu: Move the selection to the next item. Using the IR remote control The recorder is supplied with an infrared (IR) remote control unit. Like the mouse, it can be used to operate all of the main functions of the unit.
  • Page 25 Chapter 4: Operating instructions Item Description Mon A and Mon B Switch between monitors A and B. Live Return to live view mode. Menu Activate the main menu. Start /stop sequencing. In Menu mode: Use left or right arrow buttons to select and up or down arrow buttons to edit entry.

  • Page 26: Menu Overview

    Chapter 4: Operating instructions Troubleshooting the remote control If the IR remote control is not functioning properly, perform the following tests: • Check the battery polarity. • Check the remaining charge in the batteries. • Check that the IR remote control sensor is not masked. If the problem still exists, please contact your administrator.
  • Page 27 Chapter 4: event setup Table 5: Description of the menu toolbar icons Icon Name Description Display Settings Configures display settings including video format, resolution, video output interface, dwell time, multiview format, and camera sequencing. See Chapter 9 “Display settings” on page 55. Camera Setup Configures analog and IP cameras, snapshot resolution and quality, camera settings including OSD, privacy masking, tampering,...

  • Page 28: Exiting The Main Menu

    Chapter 4: event setup 3. Click Apply to save the settings. 4. Click Exit to leave the menu setup and return to live view. The soft keyboard A keyboard will appear on-screen when you need to enter characters in a window option. Click a key to input that character.

  • Page 29: Live View

    Chapter 5 Live view Description of live view Live view mode is the normal operating mode of the unit where you watch live images from the cameras. The recorder automatically enters into live view mode once powered up. On the monitor you can see whether a recording is in progress and, if set up to do so, the current date and time, as well as the camera name.

  • Page 30: Video Output

    Chapter 5: Live view The recorder can display more than one icon at the same time. See “Display settings” on page 100 to display or hide the status icons. See “Alarm notification types” on page 95 and enable or disable the option “Display Event Icon”. The system status is displayed on the front panel by the status LEDs.
  • Page 31 Chapter 5: Live view Table 7: Mouse menu for monitor A (main monitor) Name Description Menu Enter the Main menu. This option is not available from monitor B. Single Camera Switch to a full-screen view for the selected camera from the dropdown list. See “Single and multiview display ”...

  • Page 32: Single And Multiview Display Mode

    Chapter 5: Live view Single and multiview display mode The recorder has single and multiview formats. The number of multiview display modes available depends on the recorder model. Single view display Press the numeric button on the front panel to switch to the corresponding camera format display.
  • Page 33 Chapter 5: Live view Figure 8: Live view toolbar Table 9: Description of the live view toolbar icons Icon Description Pause: Freeze the live image of the selected camera. Although the image pauses, time and date information does not. The system clock continues to run. Start Manual Recording: Start/stop manual recording.

  • Page 34: Digital Zoom

    Chapter 5: Live view Icon Description Close Toolbar: Close the toolbar. Digital zoom You can easily zoom in or out of a camera image in live view mode and playback using the digital zoom command. The zoom command magnifies the camera image four times. See Figure 9 below.
  • Page 35 Chapter 5: Live view Front panel Press Enter. PTZ control panel appears. Mouse Left-click the mouse on the desired camera image. The live view toolbar appears. Click the PTZ control icon to enter PTZ mode. The PTZ control panel appears. Remote control Press the OK button.
  • Page 36 Chapter 5: Live view To call up a preset: 1. In live view, left-click the mouse and select the PTZ control icon in the quick access toolbar. The PTZ control panel appears. Select the desired camera from the toolbar. – Or – On the front panel, select the desired camera and press Enter to call up the quick access...

  • Page 37: Playback Functionality

    Chapter 6 Playback functionality The recorder lets you quickly locate and play back recorded video. There are four ways to play back video:  Instant playback of the most recently recorded video  24-hour playback of one day’s recorded video ...
  • Page 38 Chapter 6: Playback functionality Figure 11: Playback window (24-hour playback shown) 1. Playback viewer. 5. Time bar: Time of actual playback. This is only displayed in 24-hour playback. 2. Camera panel. Select the cameras for playback. Move the mouse over the area to 6.
  • Page 39 Chapter 6: Playback functionality Figure 12: Playback control toolbar (Search playback example shown) Description Audio and video control toolbar: Audio on/off. Start/stop a video clip during playback. Sections of a recording can be saved to an external storage device. Add default bookmark. Add customized bookmark.

  • Page 40: Playback Mouse Menu

    Chapter 6: Playback functionality Description Timeline: Allows you to jump forwards or backwards in time. The timeline moves left (oldest video) to right (newest video). Click a location on it for where you want playback to start. In 24-hour playback, the cursor shows the actual time. In search playback, the cursor is a ball.

  • Page 41: 24-Hour Playback

    Chapter 6: Playback functionality You can modify the playback period in the Instant Replay Duration menu. See page 90 for further information. To instantly replay recorded video: 1. In live view mode, left-click the mouse on the desired camera image. The live view toolbar appears.

  • Page 42: Playback Speed And Skip Time

    Chapter 6: Playback functionality 3. Use the playback control toolbar to manually control playback. 4. Click Exit to return to live view. – Or – Right-click the mouse and click Exit from the mouse menu to return to the previous window. •...

  • Page 43: Play Back Frame-By-Frame

    Chapter 6: Playback functionality Play back frame-by-frame You can play back a selected video at different speeds. This allows you to carefully examine an event frame-by-frame as it happens. The current frame rate is shown on the right of the playback control toolbar. To play back frame-by-frame: •...
  • Page 44 Chapter 6: Playback functionality • Default bookmark : All default bookmarks have the same generic name, “BOOKMARK”. • Customized bookmark : The bookmark is given a name for easy identification. The same name can be used for several bookmarks. You can search both types. To create a bookmark: 1.

  • Page 45: Searching Files

    Chapter 7 Searching files This chapter describes how to search and playback recorded videos as well as search them by time, events, bookmarks, and snapshots. Search video menu You can easily search and play back recorded videos by time and date, events, bookmarks, and snapshots.

  • Page 46: Search For Motion Events In Playback

    Chapter 7: Searching files Description Snapshot: Search snapshots. Disk analysis: The recorder can run a disk analysis to get a broader sense of the video data stored on the HDD. This video data can include alarms, events, video loss, and more. Recorded video cannot be retrieved from this window.

  • Page 47: Search And Play Back Recordings By Time And Video Type

    Chapter 7: Searching files Description Click to call up the previously used line to detect motion. If you want to reposition or change the line, click the delete icon and draw a new line. See “Line crossing detection” on page 66 for further information. Click to call up the previously used quadrilateral shape to detect motion.

  • Page 48: Search And Playback Recordings By Event

    Chapter 7: Searching files To immediately access archived footage: 1. In the Search menu, click the “Time & Date” tab. 2. Select the desired cameras, record type, file type as well as start and end times of the recording. Up to eight cameras can be selected. 3.

  • Page 49: Search Bookmarked Recordings

    Chapter 7: Searching files Search bookmarked recordings For information on creating bookmarks, see “Create bookmarks” on page 41. To search for a bookmark: 1. In live view right-click the mouse on the desired video pane and select Search Video. The Search menu appears.

  • Page 50: Log Search

    Chapter 7: Searching files Log search You can open video footage from the results of a log search. Refer to “Search the system log” on page 121 for more information. Disk analysis The recorder can run a disk analysis to get a broader sense of the video data stored on the HDD.

  • Page 51: Archiving Files

    Chapter 8 Archiving files Archive recorded files on an external device such as USB flash drive, USB HDDs or a DVD burner. You must be in live view to archive video. Access to archive commands may require a password. Before starting to archive files, ensure that you have the backup device connected to the recorder.

  • Page 52: Archive Menu

    Chapter 8: Archiving files Archive menu You can insert a mini-USB hub to the USB port to attach a mouse for navigation or a USB drive for archiving. However, the unit may not support all types of USB hubs. The Archive options available may depend on the type of backup device selected. Figure 16: Example of an archive menu Function Description...

  • Page 53: Searching And Playing Back Recorded Video

    Chapter 8: Archiving files Searching and playing back recorded video 1. In live view, press the Search button on the front panel. – Or – In live view, right-click the mouse to call up the mouse menu. Click Search Video. Note: If you are not already logged into the recorder you will have to enter your username and password.
  • Page 54 Chapter 8: Archiving files 4. The Archive window appears. Under Device Name, select the storage media used for archiving. 5. Check Include Player (or Player Backup depending on the recorder model) to include the Player tool with the archived files. 6.

  • Page 55: Exporting Video Recordings Via Truvision Navigator

    Chapter 8: Archiving files 8. The Archive window appears. Under Device Name, select the storage media used for archiving. 9. Check Include Player Player Backup depending on the recorder model) to include the Player tool with the archived files. 10. Click Archive to export the currently selected video file.
  • Page 56 Chapter 8: Archiving files You can include multiple files in the TruVision Player playlist. Double-click the desired video file from the list and click the Start button. When the first file finishes, the next file will automatically start. Merging video files in TruVision Player 1.

  • Page 57: Display Settings

    Chapter 9 Display settings Use the Display Settings menu to modify how the camera images appear on screen. Display settings Use the Display Settings menu to adjust the settings related to the local monitor output of the recorder, such as selecting the main and event monitors, multiview layout, display the monitor time bar, sequence dwell time options, and enable or disable the local audio output.

  • Page 58: Layout

    Chapter 9: Display settings Option Description Modify the video standard used to PAL or NTSC, and click Apply. Picture Setting Define the desired output mode. Select one of the options from the drop-down list: Standard, Bright, Soft, or Vivid, and click Apply. BNC Output Brightness Modify the video output brightness.
  • Page 59 : Display settings The camera order in the different views is consistent. This means that if Channel 2 is the first camera shown in the single camera view then it will also be the top left camera of the 4-channel view.

  • Page 60: Camera Setup

    Chapter 10 Camera setup Use the Camera Setup menu to configure analog and IP cameras. You can also configure the camera OSD, snapshots, recording settings, motion detection, privacy masking, camera tampering, PTZ configurations and V-stream settings. Note: Not all settings are available for IP cameras. For advanced IP camera settings, please consult the IP camera web browser interface.

  • Page 61: Ip Camera Status

    Chapter 10: Camera setup Figure 19: Overview of analog cameras window (8-channel recorder model shown) List of all the analog channels (number depends on Click to live view the selected analog camera. recorder model). Disable an analog camera in order to add an IP camera.
  • Page 62 Chapter 10: Camera setup Figure 20: IP camera window Table 12: Description of the IP camera window Option Description IP camera list This shows the list of IP cameras added to the recorder. The camera information shown is: Camera No., Status, Edit, Advanced Set, Live View, Camera Name, IP Camera Address, Manage Port, Protocol, Device Model, Serial Number, and Firmware.

  • Page 63: Camera Recording Settings

    Chapter 10: Camera setup Note: If cameras still have default settings, they might have the same IP addresses. This creates an IP conflict. Use the Edit button to assign a different IP address to each camera. Ensure that for each camera to successfully connect the cameras. To manually add an IP camera: 1.
  • Page 64 Chapter 10: Camera setup • Video Quality: Select the quality at which to record. If “Constant” is selected as the bit rate type, this option is unavailable. If a low video quality is selected, the image quality is poorer and the bandwidth required is reduced thereby allowing recording over a longer period of time.

  • Page 65: Snapshots

    Chapter 10: Camera setup Snapshots You can define the image quality and resolution of snapshots for each camera. Snapshots can be taken at any time during live view or playback, or can be created when an alarm occurs and sent by email or sent to an FTP server. To configure snapshots: 1.

  • Page 66: Image Settings

    Chapter 10: Camera setup 2. Enter a name for the camera (1), if required. The name can have up to 32 alphanumeric characters. 3. Check the Display Name (2), Display Date (3), and Display Day (4) boxes to display the camera name, date, and week.

  • Page 67: Motion Detection

    Chapter 10: Camera setup Click the Default button to return image setting values to the default position. 4. Click Apply to save the settings and then click Exit to return to live view. Motion detection The motion detection menu allows you to enable or disable motion detection for each camera, as well as create motion grids, set the sensitivity of the motion detection and link motion detection to a specific action.

  • Page 68: Line Crossing Detection

    Chapter 10: Camera setup In the Actions window, click the Arming Schedule tab and select the day of the week and the time periods during the day when motion can be recorded. You can schedule up to eight time periods in a day. Default is 24 hours. Click Apply to save the settings.
  • Page 69 Chapter 10: Camera setup To define line crossing detection: 1. From the menu toolbar, click Camera Setup > VCA(SMD) > VCA. 2. Select the camera to detect line crossing motion. Each camera must be set up individually. 3. Under “Type”, select Line Crossing Detection and check Enable. 4.

  • Page 70: Intrusion Detection

    Chapter 10: Camera setup Send Email Send an email to a specified address when there is a line crossing detection alarm. Note: You must configure email settings before enabling this option. See “E-mail settings” on page 83 for further information. If you want to send the event snapshot together with the email, check the “Attached Snapshot”...
  • Page 71 Chapter 10: Camera setup Figure 22: Intrusion detection window To define line crossing detection: 1. From the menu toolbar, click Camera Setup > VCA(SMD) > VCA. 2. Select the camera to detect line crossing motion. Each camera must be set up individually. 3.

  • Page 72: Privacy Mask

    Chapter 10: Camera setup Full-screen Monitoring When an alarm is triggered, the monitor (VGA or HDMI) displays an image in live view mode. For alarms that are triggered simultaneously, images display one at a time every 10 seconds (default dwell time). Change the desired sequence dwell time under Display Settings>Display>Sequence Dwell Time.

  • Page 73: Camera Tamper

    Chapter 10: Camera setup To setup a privacy mask: 1. From the menu toolbar, click Camera Setup > Privacy Mask. 2. Select the camera for which to set up privacy masking. 3. Check the Enable Privacy Mask box to enable the feature. 4.

  • Page 74: Restricted Access Camera

    Chapter 10: Camera setup 5. Select the recording schedules for the tamper. Click Actions and then select the Arming Schedule tab to select the day of the week and the time periods during the day when motion can be recorded. You can schedule up to eight time periods in a day.

  • Page 75: Configure Ptz Settings

    Chapter 10: Camera setup To set up a camera for a restricted access view: 1. From the menu toolbar, click Camera Setup > Restricted Access Camera. 2. Check which analog camera or cameras you want to have restricted access and click Apply.
  • Page 76 Chapter 10: Camera setup Figure 24: PTZ configuration window Table 13: Description of the PTZ configuration window Name Description Save preset Saves preset. Call preset Calls up pre-existing preset. Shadow tour toolbar Starts recording the shadow tour. Saves the shadow tour. Starts the selected shadow tour.
  • Page 77 Chapter 10: Camera setup If the desired preset number is larger than the 17 numbers listed, click […]. The Preset window appears. Select a preset number from the dropdown list and click the button to save changes. Note: Presets can be overwritten. 4.

  • Page 78: V-Stream Encoding

    Chapter 10: Camera setup 5. In the preset tour toolbar, click to call up the preset tour. 6. Click Exit to return to live view. To call up a preset tour: 1. Click the PTZ Settings icon on the menu toolbar and select More Settings.
  • Page 79 Chapter 10: Camera setup Note: It is not recommended to use the V-stream feature when an analog monitor is used as a main monitor because the analog main monitor and the V-stream use the same output. To enable V-streaming: 1. Click the Display Settings >...

  • Page 80: Network Settings

    Chapter 11 Network settings The Network settings menu allows you to manage all network related aspects of the recorder including general network settings, DDNS, NTP synchronization, email setup and FTP server setup. Additionally, the Net Detect and Network statistics menus provide you with a useful and efficient tool to analyze the behavior of the recorder on the network.
  • Page 81 Chapter 11: Network settings 2. Enter the required settings: Option Description NIC Type Network interface card (NIC) is a device used to connect the recorder to a network. Select the NIC type used from the drop-down list. Default value is 10/100M self-adaptive for the 4 channel recorder and 10/100/1000M self-adaptive for the 8 or 16 channel recorders.

  • Page 82: Pppoe Settings

    Chapter 11: Network settings Option Description Multicast IP Enter a D-class IP address between 224.0.0.0 to 239.255.255.255. Only specify this option if you are using the multicast function. Some routers prohibit the use of multicast function in case of a network storm. Enable Telnet For Technical Support purposes only.

  • Page 83: Ddns Settings

    Chapter 11: Network settings DDNS settings DDNS servers allow you to connect to your recorder using a fixed address. This fixed address needs to be registered with a DNS service. The DDNS setup menu allows you to enable or disable DDNS and to configure it using ezDDNS, No-IP or DynDNS. Note: Some service providers block the default RTSP streaming port 554 used for video streaming, so if you are not receiving video images over the internet, you may need to change it to another value.

  • Page 84: Ntp Server Settings

    Chapter 11: Network settings The maximum length for the host name field is 64 characters. This limit does not include tvn-ddns.net. An example of a host name could be max64chars.tvr-ddns.net. - Or - DynDNS: Select DynDNS and enter the server address for DynDNS. In the recorder domain name field, enter the domain name obtained from the DynDNS web site.

  • Page 85: E-Mail Settings

    Chapter 11: Network settings 4. Click Apply to save the settings and click Exit to return to live view. E-mail settings The recorder can send email notifications of alarms or notifications through the network. Note: Ensure that the DNS address has been set up correctly beforehand. To configure email settings: 1.

  • Page 86: Configure An Ftp Server To Store Snapshots

    Chapter 11: Network settings Configure an FTP server to store snapshots You can upload your snapshots to an FTP server for storage. Note: It is not possible to stream video to an FTP site. To configure the FTP server settings: 1.

  • Page 87: Network Status

    Chapter 11: Network settings Manual mapped type: You enter the particular external port settings and IP addresses required to connect to the desired router (see Figure 26 below). Figure 26: UPnP auto configuration screen To enable UPnP: 1. Connect the recorder to the router. Note: The router must support UPnP and this option must be enabled.
  • Page 88 Chapter 11: Network settings To check network traffic: 1. From the menu toolbar, click Network Settings > Net Detect. The Traffic window appears. The information displayed is refreshed once a second. To check network delay and packet loss: 1. From the menu toolbar, click Network Settings >...

  • Page 89: Export Network Packet Data

    : Network settings Export network packet data When the recorder is connected to a network, you can export the captured data packet to a USB-flash drive, SATA/eSATA CD-RW and other local backup devices. To export network packet data: 1. From the menu toolbar, click Network Settings >...

  • Page 90: Recording

    Chapter 12 Recording Use the Recording menu to define the camera recording schedules, modify the instant playback duration, and to select the cameras for manual recording. Recording schedule Defining a recording schedule lets you specify when the recorder records video and which pre- defined settings are used.
  • Page 91 Chapter 12: Recording  TL-Lo (Bright green): Low quality time lapse. Records low quality video. This could be used, for example, for night recordings when few events or alarms are expected. Saving the video in low quality helps save resources on the HDD. ...

  • Page 92: Modify The Instant Replay Duration

    Chapter 12: Recording 5. Select the day of the week (1) for which you want to set up the schedule. You can define a different schedule for each day of the week. 6. Set the start and end time for recording. Define a time period by entering a start (left column) and end (right column) time.

  • Page 93: Manual Recording

    : Recording To modify the preprogrammed time of this instant replay, go to Recording > General. Select one of the times from the drop-down list (5, 10, 20, or 30 minutes) and click Apply. Default is 5 minutes. Manual recording The recorder lets you manually record video during live view.

  • Page 94: Alarm And Event Setup

    Chapter 13 Alarm and event setup This chapter describes the alarm and event setup menu and provides more information on the different types of alarms and connected responses. Set up alarm inputs The recorder can be configured to record when an alarm is triggered by an external alarm device (for example, PIR detector, dry contacts…) “A”...

  • Page 95: Set Up Alarm Outputs

    Chapter 13: Alarm and event setup 6. Select the recording schedules for the external alarm. In the Actions window, click the Arming Schedule tab and select the day of the week and the time periods during the day when motion can be recorded. You can schedule up to eight time periods in a day.

  • Page 96: Manual Trigger

    Chapter 13: Alarm and event setup To set up an alarm output: 1. From the menu toolbar, click Alarm & Event Setup > Alarm Output. 2. Select the alarm output. 3. Select a timeout option between 5 and 600 seconds or select “Manually Clear”. The timeout setting lets you define how long an alarm signal remains active after the alarm has ended.

  • Page 97: Buzzer Settings

    Chapter 13: Alarm and event setup Buzzer settings When an alarm is triggered by the system or a camera, the recorder can be set up to respond with a warning buzzer. The buzzer time is the time that it takes for the recorder to time-out the buzzer when a continuous alarm occurs.

  • Page 98: Detect Video Loss

    Chapter 13: Alarm and event setup To set up system notifications: 1. From the menu toolbar, click Alarm & Event Setup > Notification. 2. Select a system alarm notification type (see “Types of system alarm notifications” below). 3. Check one or more response method: Display event icon, event priority, enable alarm audio, notify alarm host, send email, and trigger alarm output.

  • Page 99: Alarm Host Setup

    Chapter 13: Alarm and event setup 5. Set the arming schedule for detecting video loss. Click the Actions tab and select the schedule of when you want video loss detection to be enabled. The schedule can be set for all week or any day of the week with up to 8 time periods per day.

  • Page 100: Device Management

    Chapter 14 Device management This chapter describes how to:  Set up the time and date of the recorder  Select the recorder language and set up general system parameters such as the device name, menu timeout period, and enable/disable password requirement ...
  • Page 101 Chapter 14: Device management Figure 28: Time and date settings window Table 14: Description of the Time and Date settings window Option Description 1. Time Zone Select a time zone from the list. 2. Date Format Select the date format from the drop-down list. Default format is DD-MM-YYYY. 3.

  • Page 102: General Recorder Settings

    Chapter 14: Device management General recorder settings Use the Device Management menu to configure general recorder options. See Figure 29 and Table 15 on page 100 for the general options available. The changes are immediately implemented once Apply is clicked to save the settings. Figure 29: General settings of the recorder Table 15: Description of the Monitor setup window: General settings Option...

  • Page 103: Configuration Files

    Chapter 14: Device management Option Description Menu Timeout Define the time in minutes after which the menu window reverts to live view mode. Select a time from the drop-down list, and click Apply. Menu timeout also applies to the system idle time after which a password will be required. Default value is 5 minutes.

  • Page 104: Upgrade System Firmware

    The firmware upgrade file is labeled TVR44HD.dav. To update the system firmware using a USB device: 1. Download the latest firmware from our web site at: www.interlogix.com - Or - www.utcfssecurityproductspages.eu/videoupgrades 2. Connect the USB device to the recorder.

  • Page 105: Text Insertion

    Chapter 14: Device management 4. Select whether the holiday period will be categorized by date, week, or month and then enter the start and end dates. 5. Click Apply to save the settings and then to return to the Edit window. 6.
  • Page 106 Chapter 14: Device management Figure 30: RS-232 setup window Table 16: Description of the RS-232 settings window Option Description Baud Rate This is a measure of the speed of data transmission. Default is 115200. Data Bit A bit is the smallest unit of data in a serial communication message. A data bit is the bit carrying the information, as opposed to the start bit and the stop bit.

  • Page 107: Storage Management

    Chapter 15 Storage management This chapter describes the content of the Storage Management menu, including HDD information, Storage Mode, S.M.A.R.T. settings as well as Bad sector detection. HDD information You can check the status of any of the installed HDDs on the recorder at any time. To check the status of a HDD: 1.

  • Page 108: Hdd Redundancy

    Chapter 15: Storage management Overwrite a HDD You can select how the recorder responds when the HDDs become full and there is no longer sufficient space to save new data. The overwrite option is enabled by default. To enable overwrite when the HDDs are full: 1.

  • Page 109: Managing Esata

    Chapter 15: Storage management 4. Click Apply to save the settings and then return to the previous window. 5. In the menu toolbar, click the Camera Setup > Camera Recording. 6. Select the camera to be used for redundancy. 7. Check Redundant Record/Capture.
  • Page 110 Chapter 15: Storage management To set the HDD quota for a camera: 1. From the menu toolbar, click Storage Management > Storage Mode. 2. Under the Mode option, select Quota. 3. Select a camera whose storage capacity you want to change and enter the values in GB for the maximum record capacity and snapshot capacities.

  • Page 111: S.m.a.r.t. Settings

    Chapter 15: Storage management Create HDD groups If you have more than one HDD installed, you can change the behavior of a HDD by changing its property. It can be set to read-only or read/write (R/W). The storage mode must be set to Group before setting the HDD property.

  • Page 112: Bad Sector Detection

    Chapter 15: Storage management To view the S.M.A.R.T. information of a HDD: 1. From the menu toolbar, click Storage Management > S.M.A.R.T. Settings. 2. Select the HDD whose data you want to see. A detail listing of S.M.A.R.T. information is displayed.

  • Page 113: Install Hdds

    Chapter 15: Storage management Figure 31: Bad sector detection window To detect bad sectors: 1. From the menu toolbar, click Storage Management > Bad Sector Detection. 2. Select the HDD you want to test. 3. Select whether you want to do a key area detection or a full detection and click Detect. 4.

  • Page 114: Add A Network Storage System

    Chapter 15: Storage management 3. Use the key provided in the accessories box to unlock the recorder front panel. 4. Press the latches on both sides of the front panel to open it. 5. Install the HDDs as shown below. The first drive in position number 1, the second drive in position number 2, etc.
  • Page 115 Chapter 15: Storage management 2. Click the button. 3. Select the desired network storage from the drop-down list. You can set up to eight systems. 4. Under Type, select NAS or IP SAN. 5. Enter the network storage IP address. 6.

  • Page 116: User Management

    Chapter 16 User management By default the recorder comes with three user accounts: an Administrator account, an Operator account and a Guest account. These accounts provide multiple levels of access and functionality. See Table 17 below for a description of the different user accounts. Table 17: User accounts User Description...

  • Page 117: Customize A User's Access Privileges

    Chapter 16: User management 3. Enter the new user’s name and password. Both the user name and password can have up to 16 alphanumeric characters. 4. Select the new user’s access level: Operator or Guest. Default is Guest. 5. Enter the user’s MAC address to let the user access the recorder from a remote computer with this MAC address.

  • Page 118: Remote Configuration Settings

    Chapter 16: User management Remote configuration settings By default, only remote log search and two-way audio are enabled for operators, and only the remote log search is enabled for guests. • Remote Log Search: Remotely view logs that are saved on the recorder. •...

  • Page 119: Delete A User

    Chapter 16: User management 4. Click the button to return to the previous window. 5. Click Exit to return to live view. Delete a user Only a system administrator can delete a user. To delete a user from the recorder: 1.

  • Page 120: System Information

    Chapter 17 System information View system information To view system information: 1. From the menu toolbar, click System Information. 2. To view device information, click Device Info. You can view the device name, model, serial number, firmware version, and encoding version.
  • Page 121 Chapter 17: System information 4. To view record information, click Record. You can view the camera number, recording status, stream type, active frame rate, active bit rate versus reserved bit rate (Kbps), active resolution, active record type, and active encoding parameters. The “Preview Link Sum”...
  • Page 122 Chapter 17: System information 6. To view alarm output information, click Alarm Outputs. You can view the alarm output number, alarm name, and alarm status. 7. To view network information, click Network. You can view the IPv4 address, IPv4 subnet mask, IPv4 default gateway, IPv6 address 1, IPv6 address 2, IPv6 default gateway, preferred DNS server, alternate DNS server, enable DHCP, enable PPPoE, PPPoE address, PPPoE subnet mask, PPPoE default gateway, MAC address, serer port, HTTP port, multicast IP, RTSP service port, enable Telnet, and...

  • Page 123: Search The System Log

    Chapter 17: System information 9. Click Exit to return to live view. Search the system log Many events of the recorder, such as operation, alarm and notification, are logged into the system logs. They can be viewed and exported at any time. Up to 2000 log files can be viewed at once.
  • Page 124 Chapter 17: System information Event Type Alarm All, Alarm Input, Alarm Output, Start Motion Detection, Stop Motion Detection, Start Camera Tamper, Stop Camera Tamper Notification All, Video Loss Alarm, Illegal Login, HDD Full, HDD Error, Duplicate IP Address Found, Network Disconnected, Abnormal Record, IP Camera Disconnected, IP Camera Address Conflicted, Input/Output Video Standard Mismatch, Record Buffer Overflow, Input/recording Resolution Mismatch, IP Camera Motion Analysis Exception Operation...
  • Page 125 Chapter 17: System information - Details: Displays information on the log or recording. For a recording, it lists such information as start time, type of event, local user, host IP address, parameter type, camera number, and gives a description on the types of events recorded and when record time was stopped.

  • Page 126: Chapter 18 Using The Web Browser

    Chapter 18 Using the web browser This chapter describes how you can use the web browser interface to configure the device, play back recorded video, search through event logs, and control a PTZ dome camera. You can also specify settings on the web browser interface to optimize video playback and recording performance when operating in a low or limited bandwidth environment.

  • Page 127: Access The Web Browser

    Chapter 18: Using the web browser Access the web browser To access the recorder, open the Microsoft Internet Explorer web browser and enter the IP address assigned to the recorder, as a web address. On the logon window, enter the default user ID and password.
  • Page 128 Chapter 18: Using the web browser Figure 32: Live view in the web browser interface Table 18: Description of live view in the web browser Name Description Camera Select the camera. Menu toolbar Lets you do the following: • View live video •...

  • Page 129: Control A Ptz Dome Camera Via The Web Browser

    Chapter 18: Using the web browser Name Description Take a video snapshot. View previous and next camera respectively. If viewing in multiview format, live view moves to the next group of cameras for the selected number of video tiles. Turn audio on/off Turn microphone on/off PTZ panel Hide/display the PTZ panel.
  • Page 130 Chapter 18: Using the web browser Figure 34: Browser playback page Description Selected camera. Calendar: Selected day is highlighted. Search: Click to start searching recorded files for the selected camera. Display format: Click to change the display format in the viewer: single view or multiview display. Timeline: The timeline moves left (oldest video) to right (newest video).

  • Page 131: Search For Event Logs

    Chapter 18: Using the web browser Description Video clips: Start/stop video clip during playback. Sections of a recording can be saved to an external storage device. Download: Download video clips. Backup: Click to make back up of recorded files to save locally on the recorder. A list of the recorded files appears Audio: Click to enable/disable audio.

  • Page 132: Configure The Recorder Via The Browser

    Chapter 18: Using the web browser Figure 35: Results of a log search Configure the recorder via the browser Click Configuration on the menu toolbar to display the configuration window. There are two ways to configure the recorder: Local and Remote. Camera management Camera configuration lets you define communication and network parameters such as protocol type, maximum file size, stream type and network transmission settings.
  • Page 133 Chapter 18: Using the web browser Figure 36: Remote browser configuration window (System Information window shown) Table 19: Description of remote configuration menus Menu Function Description Camera Setup Camera Recording Define the general camera settings such as camera name, stream Settings record mode, resolution, frame rate, audio recording, and pre and post event times.
  • Page 134 Chapter 18: Using the web browser Menu Function Description more information. DDNS Define the DDNS settings. See “DDNS settings” on page 81 for more information. Define the NTC server settings. See ““NTP server settings” on page 82 for more information. Email Define the settings to send an e-mail.

  • Page 135: Text Overlay

    Chapter 18: Using the web browser Menu Function Description more information. Upgrade Firmware Upgrade the recorder firmware. See “Upgrade system firmware” on page 102 for more information. Holiday Define how recordings occur during holiday periods. See “Holiday schedules” on page 102 for more information. Text Insertion Define access device, access mode, and start string.
  • Page 136 Chapter 18: Using the web browser 3. Check the string box for the first line of text. 4. Enter the text for string 1 in the column alongside. Up to 44 alphanumeric characters can be used. 5. Repeat steps 3 and 4 for each extra line of text, selecting the next string number. 6.

  • Page 137: Appendix A Specifications

    Appendix A Specifications TVR 4408HD TVR 4416HD Video & audio input Video compression H.264 Analog video input 8-ch, 16-ch, BNC/HD-TVI BNC/HD-TVI (1.0 Vp-p, 75 Ω), (1.0 Vp-p, 75 Ω), PAL /NTSC self-adaptive PAL /NTSC self-adaptive Max. cable distance (RG-59) Up to 365.7 m (1200 ft.) Audio compression G711u 4-ch, RCA (2.0 Vp-p, 1 kΩ)
  • Page 138 Appendix A: Specifications TVR 4408HD TVR 4416HD Hard disk SATA 4 SATA interfaces 4 SATA interfaces e-SATA 1 e-SATA interface Capacity per HDD External interface Network interface 1 RJ45 10M / 100M / 1000M self-adaptive Ethernet interface Serial interface 1 RS-232 interface (for ProBridge, Challenger, Technical Support); 1 RS-485 interface (for PTZ control or KTD405 keyboard control) USB interface 3, USB 2.0...

  • Page 139: Appendix B Ptz Protocols

    Appendix B PTZ protocols Interlogix-485 Interlogix-422 KALATEL DSCP HIKVISION Honeywell INFINOVA KTD-348 LG MULTIX LILIN TruVision DVR 44HD User Manual...

  • Page 140: Appendix C Port Forwarding Information

    Note: These links are not affiliated with nor supported by Interlogix technical support. Many router manufacturers also offer guides on their websites as well as including documentation with the product. On most routers the brand and model number is located on or near the serial number sticker on the bottom of the device.
  • Page 141 Appendix C: Port forwarding information If you cannot find any information for your particular router, please contact your router manufacturer or internet service provider for further assistance. TruVision DVR 44HD User Manual...

  • Page 142: Appendix D Connect A Ptz Dome Camera

    Before the PTZ dome cameras are assembled in their housings, set their protocol and address DIP switches for the recorder. See Table 20 on page 141 for different Interlogix PTZ dome camera settings. If you are using PTZ dome cameras from another company, please refer to their configuration instructions.
  • Page 143 Appendix D: Connect a PTZ dome camera Table 20: PTZ protocols for Interlogix cameras Camera Switch setting TruVision Mini PTZ Protocol DIP switches: 12X: Indoor Dome • RS-485 (on recorder): 000000 • RS-422 (on I/O box): 100000 RS-485 communication 110000...
  • Page 144 Appendix D: Connect a PTZ dome camera Camera Switch setting TruVision Dome 16X Protocol switches: 0111 • RS-485 (on recorder): • RS-422 (on I/O box): 1111 Address switches: Select the camera ID DIP switch address as required. Baud rate: 0000 = 9600 bps 1.
  • Page 145 Appendix D: Connect a PTZ dome camera Camera Switch setting UltraView PTZ Protocol switches: • RS-485 (on recorder): 01000 • RS-422 (on I/O box): 10000 Address switches: Select the address switch address as required. 1. Protocol switches; 2. Address switches RS-422/RS-485 data connector: Legend Protocol switches:...

  • Page 146: Appendix E Ktd-405 Keypad

    Appendix E KTD-405 keypad Supported firmware TVR 44XX-YYY firmware 1.0i or higher KTD-405U (-2DU) keypad firmware: 1.4.00 Note: XXX represents the number of video channels. YYY represents the recorder storage configuration such as 1T = 1 TB, etc. Wiring the keypad Connect the RS-485 bus of the KTD-405 I/O box to the recorder keypad terminal port.

  • Page 147: Setting The Keypad To Work With The Recorder

    Appendix E: KTD-405 keypad Figure 38: Keypad and recorder connections A. KTD-405 keypad E. RJ45 cable control (use the cable provided with the equipment) B. RS-232 programming port F. I/O box C. RS-485 and RS-422 in/out G. Recorder back panel D.

  • Page 148: Recorder And Keypad Functions

    Appendix E: KTD-405 keypad 3. Change Operating Mode to Zone by moving the joystick down. 4. Quit the menu by pressing the button. The display will show, for example: 5. To connect it to the recorder, press the zone button and enter the ID number of the recorder.

  • Page 149: Operating The Keypad

    Appendix E: KTD-405 keypad Figure 39: Unavailable keypad buttons DSC/VCR Autofocus (Record mode) Aux 1 Alarm Store Aux 2 Iris +/- Fast forward Aux 3 Focus +/- Fast backward Aux 4 (Magnification) Operating the keypad You can navigate the recorder menus using the keypad buttons and joystick. However, not all maneuvers are available using the joystick.

  • Page 150: Recorder Mapping To The Ktd-405 Keypad

    Appendix E: KTD-405 keypad 7. Press and hold and then press the arrow buttons to navigate the cursor to activate OK button on the Login screen. 8. Press . The main menu appears. Example 2: To modify a menu option using the keypad 1.
  • Page 151 Appendix E: KTD-405 keypad Task Keypad action Further information  Live view mode Call up a single camera Press and then press Using the numeric buttons to 9, enter the Enter number of the camera and then press Enter Call up multiview screens Press view and then press...

  • Page 152: Controlling A Camera

    Appendix E: KTD-405 keypad Task Keypad action Further information Jump 30 seconds forwards or Press and hold esc and then backwards during playback press the up/down arrow buttons or move the joystick to the left/right. Controlling a camera When setting up and controlling your cameras in zone mode, refer to Table 23 below for the list of default PTZ addresses associated with a zone ID.

  • Page 153: Connecting A Ktd-405 Keypad And Dome Camera To The Recorder

    : KTD-405 keypad Camera Zone ID of the recorder input Connecting a KTD-405 keypad and dome camera to the recorder Use the input/output box that is supplied with the keypad to connect the KTD-405 keypad to the recorder. As the KTD-405 keypad uses full duplex data communication, you cannot connect the both keypad and a dome camera directly to the recorder from the RS-485 port as this could cause problems on the bus.
  • Page 154 8. Dome camera Table 24: UTC PTZ protocol settings Dome: RS-422 protocol Recorder: Interlogix RS-485 See Table 25 below for the bus addresses to consider when connecting a both keypad and dome camera to the recorder. Table 25: Bus addresses...

  • Page 155: Appendix F Maximum Pre-Recording Times

    Appendix F Maximum pre-recording times The maximum pre-recording time that can be selected depends on the bit rate. Frame rate, resolution and image quality do not impact time. Note: This information only applies when the bit rate is set to Constant (see “Camera recording settings”...
  • Page 156 Appendix F: Maximum pre-recording times Constant bit rate Maximum pre-recording time (seconds) 1792 2048 3072 4096 TruVision DVR 44HD User Manual...

  • Page 157: Appendix G Supported Ptz Commands

    Table 26: Supported PTZ commands by camera protocols (Part 1) PTZ command Protocol Tilt up Tilt Left Left Right Right Auto Zoom Zoom Focus Focus left righ Interlogix-485 Interlogix-422 KALATEL DSCP HIKVISION Honeywell INFINOVA KTD-348 LG MULTIX LILIN PANASONIC_ CS850 PELCO-D PELCO-P PHILIPS PHILPS-3...
  • Page 158 Table 27: Supported PTZ commands by camera protocols (Part 2) PTZ command Protocol Iris+ Iris- Light Wiper Zoom Center Menu Preset Tour Shadow area tour Interlogix-485 Interlogix-422 KALATEL DSCP HIKVISION Honeywell INFINOVA KTD-348 LG MULTIX LILIN PANASONIC_ CS850 PELCO-D PELCO-P PHILIPS...

  • Page 159: Appendix H Default Menu Settings

    Appendix H Default menu settings Display Settings Display General Monitor Video Format: NTSC/PAL. Auto detect at booting. Picture Setting: Standard BNC Output Brightness: (Null) Resolution: (Null) Display Status Icons: Yes Time Bar Transparent: (Null) Enable Timebar: Yes Video Output Interface: VGA/HDMI Default View: 1*1 (for 8-ch models), and 4*4 (16-ch models) Sequence Dwell Time: No switch...
  • Page 160 Appendix H: Default menu settings IP Camera Camera No., Status, Edit, Advanced Set, Live View, Camera Name, IP Camera Address, Manage Port, Protocol, Device Model, Serial Number, and Firmware Camera Recording Settings Record Camera Name: Analog 1 Record Stream Mode: Main Stream (TL-Hi) Stream Type: Video &...
  • Page 161 Appendix H: Default menu settings Brightness: 128 Contrast: 128 Saturation: 128 Hue: 128 Sharpness: 1 Digital Noise: 2 Motion Detection Motion Detection Settings Camera: Analog 1 Enable Motion Detection: No Actions: Trigger Channel [camera-self]; Arming Schedule - All day for whole week; Actions: (Null) Sensitivity: 3 Target size: 1 Zone: Full Screen...
  • Page 162 Settings Camera: Analog 1 Baud Rate: 9600 Date Bit: 8 Stop Bit: 1 Parity: None Flow Ctrl: None PTZ Protocol: Interlogix-485 Address: 0 to 15 for camera 1 to 16 PTZ Preset/Tours Preset/Tours Camera: Analog 1 V-stream Encoding V-stream Encoding...
  • Page 163 Appendix H: Default menu settings Alternate DNS Server: (Null) HTTP Port: 80 RTSP Server Port: 554 Total Bandwidth Limit (Kbps): 61440 PPPoE PPPoE Enable PPPoE: Disable User Name: (Null) Password: (Null) Confirm: (Null) DDNS DDNS DDNS: Disable DDNS Type: ezDDNS Server Address: www.tvr-ddns.net Host Name: (Null) Enable NTP: Disable...
  • Page 164 Appendix H: Default menu settings Enable FTP: Disable FTP Server: (Null) FTP Port: 21 User Name: (Null) Password: (Null) Directory: Use root directory Parent Directory: (Null) Secondary Directory: (Null) SNMP SNMP Enable SNMP: Disable SNMP Version: SNMP Port: 161 Read Community: public Write Community: private Trap Address: (Null) Trap Port: 162...
  • Page 165 Appendix H: Default menu settings Total Bandwidth Limit: 60Mbps Recording Recording Schedule Recording Camera: Analog 1 Enable Recording: Yes Schedule: All day for whole week TL-Hi General General Instant Replay Duration: 5 minutes Manual Recording Manual Recording Analog: Off IP Camera: Off Alarm &...
  • Page 166 Appendix H: Default menu settings Event Priority: Text In < Motion Notification Type: HDD Full Enable Alarm Audio: Disable Notify Alarm Host: Disable Send Email: Disable Trigger Alarm Output: Disable Video Loss Video Loss Settings Camera: Analog 1 Enable Video Loss Alarm: No Actions: Arming Schedule - All day for whole week;...
  • Page 167 Appendix H: Default menu settings General Settings General Language: English Device Name: TVR 44HD Remoter Control ID: 255 Keypad Zone ID: 1 Password Required : No Enable Wizard: Yes Start Wizard Now: No Menu Timeout: 5 Minutes Mouse Pointer Speed: Low Enable Front Panel Lock: No Configuration Files Import/Export Config Files...
  • Page 168 Appendix H: Default menu settings Storage Management HDD Information Label: Disable Total Capacity: Free Space: Overwrite: Enable eSATA: eSATA1 Usage: Record/Capture Storage Mode Storage Mode Mode: Quota Camera: Analog 1 Used Record Capacity: Used Snapshot Capacity: HDD Capacity (GB): Max Record Capacity (GB): Max Snapshot Capacity (GB): S.M.A.R.T.
  • Page 169 Appendix H: Default menu settings admin:1234 operator: 4321 guest: (Null) System Information Device Info System Information Device Name: TVR 44HD Model: (Model number) Serial No.: (Model’s serial number) Firmware Version: Encoding Version: Camera Camera Camera No.; Camera Name; Status; Motion Detection; Camera Tamper, Video Loss;...
  • Page 170 Appendix H: Default menu settings PPPOE Address PPPOE Subnet Mask PPPOE Default Gateway MAC Address Server Port HTTP Port Multicast IP Label; Status; Capacity; Free Space; Property; Type; Group Log search Log search Start Time: End Time: Event: All Type: All TruVision DVR 44HD User Manual...

  • Page 171: Index

    Index Digital zoom in playback, 41 Disk analysis searching recorded video, 48 Alarm notifications DST, 98 external alarms, 92 types, 95 video loss, 96 video tampering, 71 Email warning buzzer, 95 link to cross line detection alarm, 68, 70 Alarm outputs Email notifications manually acknowledging, 94 set up, 83...
  • Page 172 11 control remotely, 127 add, 112 PTZ protocols Network packet data assig, 73 exporting, 87 configuring Interlogix cameras, 140 Network settings general set up, 78 Network settings for browser, 125 Network status, 85 Recorder address Network traffic...
  • Page 173 daily, 89, 102 adding a new user, 114 defining, 88 customizing user privileges, 115 Remote alarm host settings, 97 deleting a user, 117 Remote control modify user information, 117 connect to the recorder, 23 description, 22 Resolution Video format change monitor resolution setup, 100 PAL/NTSC, 12 Restricted access, 72 Video loss...

Table of Contents