Internal Connectors - Asus A7V400-MX SE User Manual

1.10.2

1.10.2 Internal connectors

1.10.2 Internal connectors Internal connectors Internal connectors
1.10.2 1.10.2 Internal connectors
1 . 1 . 1 . 1 . 1 . F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y ) F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y ) F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y ) F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y ) F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y )
This connector is for the provided floppy disk drive (FDD) signal cable.
Insert one end of the cable to this connector, then connect the other
end to the signal connector at the back of the floppy disk drive.
Pin 5 on the connector is removed to prevent incorrect cable connection
when using a FDD cable with a covered Pin 5.
A7V400-MX SE
A7V400-MX SE Floppy disk drive connector
2 . 2 . 2 . 2 . I D E c o n n e c t o r s ( 4 0 - 1 p i n P R I _ I D E , S E C _ I D E ) I D E c o n n e c t o r s ( 4 0 - 1 p i n P R I _ I D E , S E C _ I D E ) I D E c o n n e c t o r s ( 4 0 - 1 p i n P R I _ I D E , S E C _ I D E )
2 . I D E c o n n e c t o r s ( 4 0 - 1 p i n P R I _ I D E , S E C _ I D E ) I D E c o n n e c t o r s ( 4 0 - 1 p i n P R I _ I D E , S E C _ I D E )
This connector is for an Ultra DMA 133 signal cable. The Ultra
DMA 133 signal cable has three connectors: a blue connector for the
IDE connector on the motherboard, a black connector for an Ultra DMA
133/100/66 IDE slave device (optical drive/hard disk drive), and a gray
connector for an Ultra DMA 133/100/66 IDE master device (hard disk
drive). If you install two hard disk drives, you must configure the
second drive as a slave device by setting its jumper accordingly.
Refer to the hard disk documentation for the jumper settings.
• Pin 20 on the IDE connector is removed to match the covered hole
on the Ultra DMA cable connector. This prevents incorrect insertion
when you connect the IDE cable.
• Use the 80-conductor IDE cable for Ultra DMA 133/100/66 IDE devices.
A7V400-MX SE
A7V400-MX SE IDE connectors
A S U S A 7 V 4 0 0 - M X S E A S U S A 7 V 4 0 0 - M X S E
A S U S A 7 V 4 0 0 - M X S E A S U S A 7 V 4 0 0 - M X S E A S U S A 7 V 4 0 0 - M X S E
FLOPPY
NOTE: Orient the red markings on
the floppy ribbon cable to PIN 1.
PIN 1
NOTE: Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
PIN 1
1 - 2 1 1 - 2 1
1 - 2 1 1 - 2 1 1 - 2 1