Electrical Connection - Hotpoint CH 10750 GF S Operating Instructions Manual

Levelling
GB
Your cooker is heavy, so it would be advisable for two people to move it. The
cooker is fitted with rear wheels and will slide into position easily. Movement
of your cooker is most easily achieved as follows. Open the grill/oven door
sufficiently to allow a comfortable grip on the underside front edge of the
oven roof, avoiding any grill or oven interior furniture, and then lift and slide
back at the same time.
Your cooker must stand on a flat surface so that the hob is perfectly level, and
the cooker is stable and cannot be rocked, this is easily achieved by adjusting
the three feet which are under the front of the cooker and the 3 castors under
the rear of the cooker, if necessary.
NOTE: If the cooker is to be placed on a base, precautions must be taken to
prevent it from slipping off the base.
The cooker is designed to match the depth of standard 600mm worktops. An
adaptor backplate should, therefore, be fitted within the shaded area shown
to allow the cooker to be pushed fully to the wall. If a forward facing backplate
is used, it must be chased into the wall.
Connection to the cooker should be made with an approved appliance flexible
connection in according to National Legislation. A length of 0.9 to 1.25m is
recommended. The length of hose chosen should be such that when the
cooker is in situ, the hose does not touch the floor.
The temperature rise of areas at the rear of the cooker that are likely to come
in contact with the flexible hose do not exceed 70°C.
Installation & Operational Checks
After installation, check for gas soundness.
Fit the hotplate burner bodies, burner port rings, enamelled discs and pan
supports referring to the instructions for use where necessary.
1. Check that the hotplate burners ignite correctly and burn with a steady
flame.
Check for a steady flame on the low setting.
2. Check that with the left hand oven set at 230°C, the oven fan operates
and the oven heats up.
3. Check that with the right hand oven set at 230°C, the oven heats up.
4. Check that the twin grill heats up.
5. Check that the warming drawer heats up.
6. Check operation of clock.
Instruct the user on the operation of the cooker.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
6

Electrical connection

WARNING - THIS APPLIANCE MUST BE EARTHED. CONNECT TO A
230-240V A.C. SUPPLY ONLY.
Connection to the electricity supply should be made via a properly earthed,
readily accessible wall socket which is adjacent to but not directly above,
and not more than 1.25m away from the appliance and capable of electrical
isolation.
The mains lead should be routed such that it cannot touch hot parts of the
cooker i.e. the back panel above a height of 650mm from the floor.
Should this plug not fit the socket outlet in your home it should be cut off
and replaced with a suitable plug as outlined below.
NOTE: The removed plug cannot be used for any other appliance and should
therefore be properly disposed of and not left where children might find it and
plug it into a supply socket - with the obvious consequent danger.
IF THE FITTED PLUG IS REMOVED
The flexible mains lead must be correctly connected as below to a three pin
plug of not less than 13 amp capacity. If a B.S. 1363 fused plug is used, it
must be fitted with a fuse which is approved to B.S. 1362.
IMPORTANT: The wires in the mains lead fitted to this appliance are coloured
in accordance with the following code:
GREEN AND YELLOW - EARTH
BLUE - NEUTRAL
BROWN - LIVE
The power supply cable must be type H05RR-F
Blue to
Neutral
Cord
Clamp
As the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured green and yellow must be connected to the terminal
in the plug which is marked with the letter "E" or by the earth symbol
coloured green or green and yellow.
The wire which is coloured blue must be connected to the terminal which is
marked with the "N" or coloured black.
The wire which is coloured brown must be connected to the terminal which
is marked with the letter "L" or coloured red.
When wiring the plug, ensure that all strands of wire are securely retained
in each terminal. Do not forget to tighten the mains lead clamp on the plug.
As the appliance must be earthed, do not use 2-pin sockets outlets, if you
are in doubt, consult a qualified electrician.
Should the mains lead ever require replacement, it is essential that this
operation be carried out by a qualified electrician and should only be replaced
with a flexible cord of the same size i.e. 1.0mm
cable, available from our parts department (see Back Cover).
Green &
Yellow to
Earth
Brown
to Live
3 Amp
Fuse
or
cross sectional area PVC
2