Advertisement
! The screws for the alignment springs must remain accessible.
! In order to adhere to safety standards, the appliance must
not come into contact with electrical parts once it has been
installed.
! All parts that ensure the safe operation of the appliance
must not be removable without the aid of a tool.
! Where the hob is not installed over a built-in oven,
a wooden panel must be installed as insulation. This
must be placed at a minimum distance of 20 mm from
the lower part of the hob.
Electrical connection
Hobs equipped with a three-pole power supply cable are
designed to operate with alternating current at the voltage and
frequency indicated on the data plate (this is located on the
lower part of the appliance). The earth wire in the cable has a
green and yellow cover. If the appliance is to be installed above
a built-in electric oven, the electrical connection of the hob and
the oven must be carried out separately, both for electrical
safety purposes and to make extracting the oven easier.
Single-phase connection
If the hob is fitted with a supply cable,
Blue Brown
Green/Yellow
connect it to the mains, observing the
colour coding of the wires (see
diagram). The yellow-green earth wire
must be 5 cm longer than the other
wires.
N
L
Connecting the supply cable to the mains
The appliance must be directly connected to the mains
using an omnipolar circuit-breaker with a minimum contact
opening of 3 mm installed between the appliance and the
mains. The circuit-breaker must be suitable for the charge
indicated and must comply with current electrical regulations
(the earthing wire must not be interrupted by the circuit-
breaker). The supply cable must not come into contact with
surfaces with temperatures higher than 50°C.
! The installer must ensure that the correct electrical connection
has been made and that it is compliant with safety regulations.
Before connecting to the power supply, make sure that:
• The appliance is earthed and the plug is compliant with
the law.
• The socket can withstand the maximum power of the
appliance, which is indicated on the data plate.
• The voltage is in the range between the values indicated
on the data plate.
• The socket is compatible with the plug of the appliance.
If the socket is incompatible with the plug, ask an
authorised technician to replace it. Do not use extension
cords or multiple sockets.
! Once the appliance has been installed, the power supply
cable and the electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by
authorised technicians only (see Assistance).
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
! The manufacturer declines any liability should these
safety measures not be observed.
Start-up and use
! The glue applied on the gaskets leaves traces of grease
on the glass. Before using the appliance, we recommend
you remove these with a special non-abrasive cleaning
product. During the first few hours of use there may be a
smell of rubber which will disappear very quickly.
Switching on and operating the hob
1. Turn the ON/OFF knob towards the right, until it reaches
the position.
2. Adjust the temperature to the desired value using the
TEMPERATURE ADJUSTMENT knob.
3. This will switch on the hotplate and the corresponding
ON/OFF and TEMPERATURE indicator lights.
4. When the TEMPERATURE indicator light switches off,
this means that the set temperature has been reached.
5. A thermostat ensures the temperature remains constant,
at the set level. During the subsequent heating phase,
the TEMPERATURE indicator light switches on again.
Switching off the hob
To switch off the appliance, turn the ON/OFF in an anti-
clockwise direction, from the position to the "O" position.
Safety devices
Heat indicators
If, after the appliance has been used, the RESIDUAL HEAT
indicator light remains lit, this means that the heating zone is
still hot (temperature over 60°C); do not touch it. The indicator
light will switch off once the hotplate has cooled down.
Technical description of the models
Cooking zone
Total power
Practical advice on using the appliance
Food may be prepared directly on the surface of the hob,
with or without the use of fat or oil.
During cooking, the palette knife (supplied with the
appliance) may be used to turn/flip food.
! The surface of the hob may be marked by the palette knife;
however, this will not affect its performance.
Power
230 V
240 V
2000 W
2200 W
5
GB
Advertisement
