Yamaha YZ125N2 2022 Manuals

Manuals and User Guides for Yamaha YZ125N2 2022. We have 1 Yamaha YZ125N2 2022 manual available for free PDF download: Owner's Service Manual

Yamaha YZ125N2 2022 Owner's Service Manual

Yamaha YZ125N2 2022 Owner's Service Manual (278 pages)

Brand: Yamaha | Category: Motorcycle | Size: 12.82 MB

Table of Contents

Table of Contents

9
- Safety Information
  13
- For Safety, be Sure to Obey the Following
  13
- Location of Important Labels
  16
- Description
  17
- Identification
  18
- Vehicle Identification Number
  18
- Engine Serial Number
  18
- COLLAR (Tool for YPVS)
  19
- Valve Joint
  19
- Nipple Wrench
  19
- Sidestand
  19
- Included Parts
  19
- Important Information
  20
- Preparation for Removal and Disassembly
  20
- Replacement Parts
  20
- Gaskets, Oil Seals and O-Rings
  20
- Lock Washers/Plates and Cotter Pins
  21
- Bearings and Oil Seals
  21
- Circlips
  21
- Electrical System
  22
- Basic Service Information
  22
- Special Tools
  24
- Instrument and Control Functions
  28
- Engine Stop Switch
  28
- Shift Pedal
  28
- Kickstarter Lever
  28
- Front Brake Lever
  28
- Rear Brake Pedal
  28
- Fuel Cock
  28
- Starter Knob (Choke)
  29
- Starting and Break-In
  30
- Fuel and Engine Mixing Oil
  30
- Starting a Cold Engine
  30
- Starting a Warm Engine
  30
- Break-In Procedures
  30
- Maintenance after Break-In
  32
- Major Maintenance
  32
- Air Filter Maintenance
  32
- Torque-Check Points
  33
- Care
  35
- Motorcycle Care and Storage
  35
- Storage
  36
Specifications

39
- General Specifications
  40
- Engine Specifications
  41
- Chassis Specifications
  46
- Electrical Specifications
  47
- General Tightening Torque Specifications
  48
- Tightening Torques
  48
- Engine Tightening Torques
  49
- Chassis Tightening Torques
  50
- Cable Routing Diagram
  54
Periodic Checks and Adjustments

63
Chassis

91
- General Chassis
  94
- Removing the Number Plate
  94
- Removing the Side Cover
  94
- Front Wheel
  95
- Assembling the Front Wheel
  96
- Checking the Front Wheel
  96
- Disassembling the Front Wheel
  96
- Removing the Front Wheel
  96
- Installing the Front Wheel
  97
- Checking and Replacing the Rear Wheel Sprocket
  100
- Checking the Rear Wheel
  100
- Disassembling the Rear Wheel
  100
- Rear Wheel
  100
- Removing the Rear Wheel
  100
- Assembling the Rear Wheel
  101
- Installing the Rear Wheel
  101
- Front Brake
  103
- Checking the Front Brake Disc
  107
- Introduction
  107
- Replacing the Front Brake Pads
  107
- Assembling the Front Brake Caliper
  109
- Checking the Front Brake Caliper
  109
- Disassembling the Front Brake Caliper
  109
- Removing the Front Brake Caliper
  109
- Installing the Front Brake Caliper
  110
- Assembling the Front Brake Master Cylinder
  111
- Checking the Front Brake Master Cylinder
  111
- Removing the Front Brake Master Cylinder
  111
- Installing the Front Brake Master Cylinder
  112
- Rear Brake
  114
- Checking the Rear Brake Disc
  118
- Introduction
  118
- Replacing the Rear Brake Pads
  118
- Checking the Rear Brake Caliper
  120
- Disassembling the Rear Brake Caliper
  120
- Removing the Rear Brake Caliper
  120
- Assembling the Rear Brake Caliper
  121
- Installing the Rear Brake Caliper
  121
- Assembling the Rear Brake Master Cylinder
  122
- Checking the Rear Brake Master Cylinder
  122
- Removing the Rear Brake Master Cylinder
  122
- Installing the Rear Brake Master Cylinder
  123
- Checking the Handlebar
  126
- Handlebar
  126
- Installing the Handlebar
  126
- Removing the Handlebar
  126
- Disassembling the Front Fork Legs
  133
- Removing the Front Fork Legs
  133
- Checking the Front Fork Legs
  134
- Assembling the Front Fork Legs
  135
- Installing the Front Fork Legs
  141
- Steering Head
  143
- Checking the Steering Head
  144
- Installing the Steering Head
  144
- Removing the Lower Bracket
  144
- Rear Shock Absorber Assembly
  147
- Checking the Connecting Arm and Relay Arm
  149
- Checking the Rear Shock Absorber Assembly
  149
- Disposing of a Rear Shock Absorber
  149
- Handling the Rear Shock Absorber
  149
- Removing the Rear Shock Absorber Assembly
  149
- Installing the Rear Shock Absorber Assembly
  150
- Installing the Relay Arm
  150
- Swingarm
  152
- Checking the Swingarm
  153
- Installing the Swingarm
  153
- Removing the Swingarm
  153
- Chain Drive
  155
- Checking the Drive Chain
  156
- Removing the Drive Chain
  156
- Checking the Drive Sprocket
  157
- Checking the Rear Wheel Sprocket
  157
- Installing the Drive Chain
  157
Engine

159
- Engine Removal
  164
- Installing the Engine
  164
- Installing the Exhaust Pipe and Muffler
  164
- Removing the Engine
  164
- Cylinder Head, Cylinder and Piston
  166
- Removing the Cylinder Head
  168
- Removing the Piston
  168
- Removing the Push Rod
  168
- Checking the Cylinder and Piston
  169
- Checking the Cylinder Head
  169
- Combination of Piston and Cylinder
  170
- Checking the Piston Pin
  171
- Checking the Piston Ring
  171
- Assembling the Power Valve
  172
- Checking the Power Valve
  172
- Checking the Power Valve Hole on Cylinder
  172
- Checking the Small End Bearing
  172
- Installing the Piston and Cylinder
  173
- Installing the Cylinder Head
  175
- CDI Magneto
  176
- Checking the CDI Magneto
  177
- Checking the Woodruff Key
  177
- Installing the CDI Magneto
  177
- Removing the Rotor
  177
- Kickstarter
  180
- Checking the Kick Gear and Kick Idle Gear
  182
- Installing the Kick Shaft Assembly
  182
- Removing the Kick Shaft Assembly
  182
- Removing the Primary Drive Gear
  182
- Installing the Kick Idle Gear
  183
- Installing the Primary Drive Gear
  183
- Installing the Kickstarter Lever
  184
- Ypvs Governor
  185
- Checking the Bearing
  186
- Checking the Governor Groove
  186
- Installing the Governor
  186
- Removing the Governor
  186
- Checking the Clutch Boss
  190
- Checking the Clutch Housing
  190
- Checking the Clutch Plates
  190
- Checking the Clutch Springs
  190
- Checking the Friction Plates
  190
- Clutch
  190
- Removing the Clutch
  190
- Checking the Pressure Plate
  191
- Checking the Primary Drive Gear
  191
- Checking the Primary Driven Gear
  191
- Checking the Push Lever Shaft
  191
- Checking the Push Rods
  191
- Installing the Clutch
  191
- Shift Shaft
  195
- Checking the Shift Shaft
  196
- Checking the Stopper Lever
  196
- Installing the Shift Shaft
  196
- Removing the Segment
  196
- Crankcase
  199
- Assembling the Crankcase
  200
- Checking the Crankcase
  200
- Disassembling the Crankcase
  200
- Crankshaft
  203
- Checking the Crankshaft
  204
- Installing the Crankshaft
  204
- Removing the Crankshaft
  204
- Checking the Shift Drum Assembly
  207
- Checking the Shift Forks
  207
- Checking the Transmission
  207
- Removing the Transmission
  207
- Transmission
  207
- Installing the Transmission
  208
Cooling System

211
- Cooling System Diagrams
  212
- Checking the Radiator
  214
- Installing the Radiator
  214
- Radiator
  214
- Water Pump
  216
- Assembling the Water Pump
  217
- Checking the Water Pump
  217
- Disassembling the Water Pump
  217
Fuel System

219
- Fuel Tank
  220
- Air Filter
  221
- Carburetor
  222
- Checking the Carburetor
  225
- Handling Note
  225
- Assembling the Carburetor
  226
- Checking the Reed Valve
  226
- Installing the Reed Valve
  226
- Installing the Carburetor
  229
- Measuring and Adjusting the Fuel Level
  230
Electrical System

231
- Color Code
  232
- Wiring Diagram
  232
- Ignition System
  233
- Troubleshooting
  233
- Solenoid Valve System
  234
- Troubleshooting
  234
- Throttle Position Sensor System
  235
- Troubleshooting
  235
- Electrical Components
  236
- Checking the Switches
  237
- Checking the Ignition Coil
  239
- Checking the Ignition Spark Gap
  239
- Checking the Spark Plug Cap
  239
- Checking the Pickup Coil
  240
- Checking the Source Coil
  240
- Checking the Solenoid Valve Coil
  241
- Checking the Solenoid Valve Operation
  241
- Changing and Adjusting the Throttle Position Sensor
  242
- Checking the Throttle Position Sensor Coil
  242
- Handling Note
  242
- Checking the Throttle Position Sensor Input Voltage
  244
Troubleshooting

245
- General Information
  246
- Troubleshooting
  246
- Troubleshooting of Engine
  246
- Troubleshooting of Clutch
  251
- Troubleshooting of Transmission
  252
- Troubleshooting of Cooling System
  253
- Troubleshooting of Brake
  254
- Troubleshooting of Suspension
  254
- Troubleshooting of Steering/Handling
  256
Tuning

259
- Atmospheric Conditions and Carburetor Settings
  260
- Carburetor Setting
  260
- Engine
  260
- Test Run
  260
- Adjusting the Power Jet
  261
- Effects of the Setting Parts on the Throttle Valve Opening
  261
- Main Jet Adjustment
  261
- Pilot Air Screw Adjustment
  261
- Jet Needle Adjustment
  262
- Pilot Jet Adjustment
  262
- Jet Needle Groove Position Adjustment
  263
- Relationship with Throttle Opening
  263
- Carburetor Setting Parts
  264
- Examples of Carburetor Setting Depending on Symptom
  265
- Road Condition and Examples of Carburetor Setting
  265
- Change of the Heat Range of Spark Plugs
  267
- Chassis
  268
- Drive and Rear Wheel Sprockets Setting Parts
  268
- Selection of the Secondary Reduction Ratio
  268
- Change in Amount and Characteristics of Fork Oil
  269
- Front Fork Setting
  269
- Setting of Spring after Replacement
  269
- Choosing Set Length
  270
- Front Fork Setting Parts
  270
- Rear Suspension Setting
  270
- Rear Shock Absorber Setting Parts
  271
- Setting of Spring after Replacement
  271
- Suspension Setting (Front Fork)
  273
- Suspension Setting (Rear Shock Absorber)
  274

Advertisement

Advertisement

Related Products

Yamaha Categories

Motorcycle Musical Instrument Electronic Keyboard Receiver Amplifier

More Yamaha Manuals