Minebea Intec CSD-903-P07 Indicator Manuals

Manuals and User Guides for Minebea Intec CSD-903-P07 Indicator. We have 1 Minebea Intec CSD-903-P07 Indicator manual available for free PDF download: Operating Instructions Manual

Minebea Intec CSD-903-P07 Operating Instructions Manual

Minebea Intec CSD-903-P07 Operating Instructions Manual (244 pages)

Brand: Minebea Intec | Category: Accessories | Size: 1 MB

Table of Contents

Table of Contents
3
Introduction
11
Read the Manual
11
This Is What Operating Instructions Look Like
11
This Is What Lists Look Like
11
- This Is What Menu Items and Softkeys Look Like
  11
This Is What the Safety Instructions Look Like
11
- Hotline
  12
- Safety Instructions
  13
General Information
13
Intended Use
13
For Safe Operation
13
- Location of Installation
  13
Installing the Instrument
14
Power Supply
16
Operating Precautions
16
Conformed Standards
17
- Names and Functions of Parts
  19
Front Panel
19
Rear Panel
21
Side
22
Wiring
23
Precautions for Wiring

23
- Connection with Load Cells
  23
  - 6-Wire Connection Cable
    24
  - 4-Wire Connection Cable
    25
Connecting Load Cells in Parallel

26
- Connection with Power Supply and the Ground
  27
- Connecting the External Control I/O
  28
- Input Connection
  28
- Output Connection
  29
  - Connecting to a 2-Pin Method Serial Interface
    29
  - Operating
    31
  - Character Display Pattern
    31
  - Mode Changeover
    31
  - Function Settings Table
    33
  - Calibration
    37
  - Calibration Setting Items
    37
  - Parameters to be Set Where Necessary after Calibration
    37
  - Calibration Procedures
    39
  - Calibration Low
    39
  - Switch to Calibration Mode
    40
  - Set the Scale Interval
    40
  - Set the Maximum Load
    41
  - Setting the Mass of the Weight
    41
  - Zero Point Calibration
    42
  - SPAN Calibration
    43
- Quit Calibration
  45
Fine Calibration of Zero and SPAN

45
Various Operations by Function Data

78
- Digital Ilter
  78
  - Analog Ilter
    78
  - Display Frequency
    78
  - Stabilization Ilter
    78
  - Stabilization Ilter Data Width
    78
  - Stabilization Ilter Time Range
    78
  - Key Lock Function
    79
  - Key Lock 1
    79
  - Key Lock 2
    80
  - Stability Detection
    80
    
    Stability Detection Data Width
    80
    
    Duration of Stability Detection
    80
    
    Preset Tare Weight Cancellation Input
    81
    
    Preset Tare Weight Cancellation Operating Condition
    81
  - Net Weight Ofset Operation
    82
  - Print Command
    82
  - Print Operation Status
    82
    
    Hold
    82
    
    HOLD Operation
    82
  - HOLD Target
    82
  - Sub-Display Section
    83
  - Sub-Display Section Value Selection
    83
  - Accumulation
    84
    
    Accumulation Function Operating Condition
    84
  - Execute Accumulation
    84
    
    Display Range for Accumulated Value and Count
    85
    
    Clear Accumulation Value and Accumulation Times
    85
Brands (Products)

86
- Brand Changeover
  86
- Brand Number
  86
  - F Key Settings
    86
- External Control I/O Settings
  87
  - External Control Input Setting Method
    87
- External Control Output Setting Method
  88
- Memory Clear
  89
- Weighing Mode
  90
- Weighing Mode Setting Method
  91
- Setting Mode
  92
- Simple Batch Mode
  97
  - Simple Discharge Mode
    99
  - Sequential Mode
    100
  - Sequential Batch Mode (Batch In)
    100
- Sequential Batch Mode (Batch Out)
  102
  - Supplementary Batch (Discharge) Mode
    104
  - Automatic Overshoot Compensation
    106
- 4-Steps Check Mode 1
  107
- S1, S2, S3 and S4 Comparison Operation
  107
  - Comparison Targets for S1, S2, S3 and S4 in Check Mode
    108
  - Operation of S0 in Control Mode
    109
- Hysteresis in Check Mode
  111
- 4-Steps Check Mode 2
  112
- Function of SQ Function Data
  116
- Various SQ Function Data Functions
  119
  - Weighing Mode
    119
  - Control Mode
    119
  - Comparison Signal Operation
    119
- Near Zero (ZERO BAND) Comparison Operation
  119
- Full Comparison Operation
  119
- Batch Monitoring Timer
  119
- Batch Start Time Operation Setting
  120
- Coarse) Low Comparison Stop Timer
  120
- Middle) Low Comparison Stop Timer
  120
- Automatic Overshoot Correction Width
  121
- Save Automatic Overshoot Value
  121
- Judgment Condition
  121
- Calming Time
  121
  - Post-Batching Operation Setting
    122
  - Maximum Time of Post-Batching
    122
- Judgment Condition after Post-Batching
  122
- Post-Batching Time
  122
- Calming Time after Post-Batching
  122
- Weighing Inish Output Operation Setting
  122
- Discharge Start at Weighing Inish
  123
- Discharge Monitor Timer
  123
  - Discharge Gate Close Delay Time
    123
  - Discharge Inish Output Time
    123
  - Tare Weight Cancellation at Discharge Inish
    123
  - Accumulation Clear
    123
  - SQ Function Clear
    124
  - Storage Location of Setting Data
    125
  - Data Stored in Internal RAM
    125
  - Data Stored in EEPROM
    125
  - Change the Storage Location for Data
    125
  - Check Mode
    126
  - Check Mode Setting Method
    126
Ezcts Mode

127
- Conirmation of ROM Version
  128
- Conirmation of Options
  128
- Conirmation of External Control Input
  128
- Conirmation of External Control Output
  129
- Conirmation of Load Cell Output Voltage
  130
- Conirmation of BCD Output
  131
- Conirmation of Analog Output
  131
15 2-Pin Method Serial Interface (S-I/F)

133
- Interface Speciication
  133
- Data Format
  133
- Explanation of Format Data
  134
- Explanation of Output Type
  134
- Standard RS-485 Communication
  135
- Speciications for Standard RS-485 Communications
  135
- Data Format
  135
- Standard RS-485 Communication Settings
  135
Operation Mode

135
- Speciications of Communication by RS-485
  136
  - Address Setting
    136
  - Delay Time of RS-485 Return Data
    136
Transmission Data Decimal Point Detection

137
- Interface Stream Mode Output Target
  137
  - Connecting Method
    137
  - One to One
    137
- One to N
  138
  - Modbus Communication
    139
  - Calibration by Transmission through Modbus Interface
    154
  - Calibration Mode
    154
  - Zero and SPAN Ine Calibration Mode
    158
  - Calibration Mode for Digital Linearization
    161
  - Calibration of Zero Point Only
    165
  - Options
    167
  - Analog Output
    167
- Current Output Speciications (Model: CSD-903-P07)
  167
  - Voltage Output Speciications (Model: CSD-903-P25)
    167
  - Connection of Analog Output
    168
- Analog Output Target
  168
  - Scaling of Analog Output
    168
  - Analog Output Ine Calibration
    170
  - BCD Output
    171
  - Speciications (Model CSD-903-P15)
    171
  - Operation Mode of BCD Output
    171
  - BCD Output Target
    171
  - Logic of BCD Output
    172
  - Width of P.C. (Print Command)
    172
  - BCD Output Times
    172
  - Pin Assignment of the BCD Output
    172
  - I/O Equivalent Circuits
    174
  - Timing Chart
    174
  - Output Condition
    175
  - RS-232C and RS-422/485 Interface
    175
  - RS-232C Interface Speciication (P/N: CSD-903-P74)
    175
  - RS-422/485 Interface Speciication (P/N: CSD-903-P76)
    176
  - Operation Mode of RS-232C and RS-422/485
    176
  - Output Target Synchronized with RS-232C Print for RS-232C and RS-422/485
    177
  - Communication Speciications by RS-232C and RS-422/485
    178
  - Address Settings for the RS-422/485 Interface
    178
- Changeover of RS-422/485
  178
Delay Time for RS-485 Return Data

178
- Transmission Data Decimal Point Usage for RS-232C and RS-422/485
  178
- Pin Assignment of the RS-232C Interface
  179
  - Pin Assignment of the 422/485 Interface
    180
- Data Format of Command Mode
  183
  - Data Format Synchronizing with Data Format in Stream Mode
    205
- Data Format Communication Calibration
  207
  - Maintenance
    218
  - Lifetime of Used Parts
    218
  - Replacing the Fuse
    218
  - Troubleshooting
    220
  - Execute Trouble Shooting
    220
- Error Display and Buzzer Sound
  232
- Error Display
  232
- Error Sub-Display
  233
- Sequence Error Display
  233
Appendix

235
- Customer Service
  235
- Speciications
  235
  - Analog Speciications
    235
  - Display Speciications
    235
  - Interfaces
    237
  - General Speciications
    239
  - Standard Shipping Speciications
    240
  - Accessories
    240
  - Data Format of Command Mode
    241
  - Data Format Synchronizing with Data Format in Stream Mode
    241

Advertisement

Advertisement

Related Products

Minebea Intec Categories

Scales Accessories Cable Box Industrial Equipment Racks & Stands

More Minebea Intec Manuals