User Manuals: Lamtec ETAMATIC S OEM Fuel Ratio Control

Manuals and User Guides for Lamtec ETAMATIC S OEM Fuel Ratio Control. We have 2 Lamtec ETAMATIC S OEM Fuel Ratio Control manuals available for free PDF download: Manual, Quick Reference

Lamtec ETAMATIC S OEM Manual

Lamtec ETAMATIC S OEM Manual (160 pages)

Brand: Lamtec | Category: Control Unit | Size: 5 MB

Table of Contents

Table of Contents
3
1 General Information

7
- Validity of These Instructions
  7
2 Safety

8
- For Your Safety
  8
- Associated Automatic Flame Guard
  9
3 Brief Description

10
4 Operating Description

11
- Starting Without Pilot Burner
  11
- Starting with Pilot Burner
  11
5 Operator Device

12
- Programming Unit
  14
  - Use of the Operating Unit
    14
  - Connecting to the ETAMATIC OEM
    14
- Customer Interface
  15
  - Using the Customer Interface
    15
  - Connecting to the ETAMATIC OEM
    15
  - Settings
    16
  - DIP Switch
    16
  - Description of the LED
    16
6 Commissioning

17
- Before Commissioning
  17
- Enter the Curve
  33
  - Release Settings by Customer Interface
    34
  - Clear Memory
    35
  - Programming the Ignition Point
    35
  - Programming the Base Firing Rate
    35
  - Programming the 3Rd up the 10Th Point
    35
  - Saving Curve
    35
  - Changing Points
    36
  - Re-Enter Range Limits
    36
- Calling the Checksums
  37
- Calling up the Hour Counter
  37
- Fault
  37
  - Reading Faults
    37
  - Via Programming Unit
    37
  - With User Interface
    38
  - Resetting Faults
    38
  - Recalling Fault History
    39
- How to Change the Password
  39
- How to Switch the Display
  40
7 Trim

41
8 Internal Burner Firing Rate Controller

56
- Purpose
  56
- Brief Description
  56
- Range Limits
  56
- Moving Screen "Actual Temperature Is too High
  56
- How to Change the Burner-Firing-Rate Controller with the Customer Interface
  56
- Change the Setpoint of Power Control Unit Via Programming Unit
  57
- Input Signals
  58
- Operating Description
  58
- Steam Pressure
  58
- Control by Atmospheric Condition
  58
- Setpoint Changeover
  59
- Start-Up Sequence
  60
- Thermostat and Control Range
  61
- Manual Control
  63
- Meaning of the Display
  63
- How to Adjust the Burner Firing Rate Controller
  63
- Control Range
  63
- Checking of the Safety Limiter
  64
9 Control Mode

65
- Aides for Setting
  66
- Valve Leakage Test
  68
  - Valve Leakage Test Flow Chart
    69
  - Calculation Example
    70
10 Appendix

71
- Mode Abbreviations Used
  71
- Flame Monitoring
  72
- Avoiding EMC Effects
  76
- Fault Codes
  77
- Calling up the Condition of the Digital Inputs
  99
- Tips and Tricks
  100
  - Set Pilot Burner
    100
  - Post-Measurement of Safety Times
    100
- Process Sequence Charts
  101
- Connection Diagrams
  109
- Connection Examples Regular Firing Rate Input
  111
- Permitted Cable Lengths
  112
- Connections in Non Grounded Power Line Networks
  113
- Flame Scanner and Sensor Connection
  114
  - Flame Scanner Connection
    114
  - Flame Sensor Connection
    115
  - FFS07 Assembly
    115
  - FFS08 Assembly
    116
- Connecting Diagram of Customer Interface
  117
- Lamtec System Bus (Lsb)
  121
  - Configuration of the Processor Board
    121
  - LSB Connection
    122
  - LAMTEC SYSTEM BUS Plug
    124
  - LSB Cable Connection
    126
- Modem for Remote Control
  126
- Internal Connecting Diagram of the Control Output Device
  127
- Valve Leakage Test Venting over the Roof
  128
- Schalter und Tastenkombination der Bedieneinheit
  130
  - Programming Unit
    130
  - Customer Interface
    131
  - Initial State
    131
  - Display Level 1
    132
  - Display Level 2
    132
  - Manual
    132
  - Special Functions
    133
  - Reset
    133
  - Other Functions
    133
- Sensor
  133
- External Switching of the Fuel Motors/ Valves
  139
- Feedback at Three-Point-Step Channels
  140
  - Connect with Positive Locking
    140
  - Fail-Safe Feedback
    140
  - Examples of Potentiometers and Motors
    141
- Changing Control Drives / Potentiometers
  142
  - How to Replace a Servo Motor
    142
  - How to Replace a Potentiometer
    142
- Replace an ETAMATIC OEM
  142
- Changing Eproms
  143
- Wiring Notes
  145
  - Shields Connection
    145
  - PE Busbar
    146
  - Control Cabinet Wiring
    146
- Run to Shut-Off Limits
  146
- Tolerance Limit in Direction Air Deficiency
  148
  - Example of a Protocol of the Parameter Settings of the Monitoring Bands
    149
- Technical Data
  150
- ETAMATIC OEM Without Internal Flame Monitor
  153
- Dimensions and Weight
  154
- Declaration of Conformity
  157

Advertisement

Lamtec ETAMATIC S OEM Quick Reference

Lamtec ETAMATIC S OEM Quick Reference (24 pages)

Brand: Lamtec | Category: Control Systems | Size: 0 MB

Table of Contents

Table of Contents
3
1 General Information

4
- Validity of These Instructions
  4
2 Safety

5
- For Your Safety
  5
3 Brief Description

6
- Life Cycle
  6
4 Operating Description

7
- Starting with Pilot Burner
  7
- Starting Without Pilot Burner
  7
5 Customer Interface

8
- Display and Operational Controls
  8
- Contrast Settings
  8
- Key Functions
  9
  - Initial State
    9
  - Display Level 1
    9
  - Display Level 2
    10
  - Manual
    10
  - Reset
    10
6 Fault

11
- Reading Faults
  11
- Recalling Fault History
  11
- Resetting Faults
  11
7 CO/O 2 Control

12
8 Internal Burner Firing Rate Controller

15
9 Appendix

18
- Mode Abbreviations Used
  18
- Fuses
  19
- EU Declaration of Conformity
  20

Advertisement

Related Products

Lamtec Categories

Control Systems Control Unit Controller Industrial Equipment Transmitter

More Lamtec Manuals