Sign In
Upload
Manuals
Brands
Instrumentarium Manuals
Dental equipment
Express
Instrumentarium Express Manuals
Manuals and User Guides for Instrumentarium Express. We have
1
Instrumentarium Express manual available for free PDF download: Service Manual
Instrumentarium Express Service Manual (66 pages)
Brand:
Instrumentarium
| Category:
Dental equipment
| Size: 1 MB
Table of Contents
Table of Contents
4
Introduction
7
Disclaimer
7
Scope
7
Instruction / Command Syntax Used in the Manual
7
Acronyms Used in this Manual
7
Operating Warnings and Precautions
8
Servicing Precautions
8
Installing and Setting-Up the S2Terminal
9
Recommended Hardware at Installation
9
Pre-Installation Requirements
9
EMI -Interference, Vibration and Operation with UPS
9
System Architecture
10
Block Diagram
10
Scanner Mechanics
11
Electronics
13
Firmware
15
Unit Statuses and Modes
17
Service Terminal
19
Accessing Service Terminal
19
Normal and Service Mode of the Unit
21
Service Command Principles
21
Service Log
22
Configuration Parameters
23
Showing / Setting Configuration Parameters
23
Autostart <Autoscan
23
Beeper
23
Energy Save Mode <Idle
23
Proximity Sensor
23
Automatic Shutdown <Off
23
Restoring Factory Settings
23
Service Commands on Field Service
24
Maintenance
26
Field Service Procedures
28
Service Policy
28
Calibrating the Reflective Sensor
28
Calibrating Resonant Scanner Amplitude
29
Gear Ratio Calibration, Command: <Gear
29
Adjusting the Plate Carrier (<Calpr Position>, <Eject> and <Start> )
31
Firmware (=Fw), Core and Display Graphics Upgrade
33
Firmware (=Fw) Upgrade
34
Core Upgrade
34
Graphics File Upgrading
34
Changing Hardware Parts
35
Replacing External Power Supply
35
Replacing R2100 Power & Analog Board
35
Replacing H1200 General Control Board (Gc)
35
Replacing H1300 Interface Board
36
Replacing Reflective Sensor
36
Replacing Home Opto Switch
36
Replacing Erasing Lamp
36
Replacing Safety Switch
36
Replacing Membrane Switch Panel
36
Replacing the Proximity Sensor
36
Replacing the Scanner Module
36
Checking Mechanical Parts
37
Drive Belt: Tension Check and Adjust, if Necessary
37
Plate Carrier Belt (Conveyor Belt): Tension Check and Adjustment
38
Plate Carrier Drive Mechanism: Cleaning and Lubricating
40
Troubleshooting with Error Codes
41
Error 032 Carrier Home too Early
41
Error 033 Timeout While Homing Carrier
41
Error 034 Timeout While Trying to Get Laser Sync
42
Error 035 Timeout When Waiting the Stabilizing of the Laser Sync
42
Error 036 Configuration Data Invalid
43
Error 037 Crc Invalid
43
Error 038 High Voltage Not Ok
43
Error 039 Log Amp Calibration Failure
44
Error 040 Carrier Unable to Leave Home Position
44
Error 041 Timeout While Trying to Get Laser Sync Averages
44
Error 042 Timeout While Trying to Get Laser Sync During Scan
45
Error 043 Erasing Lamp Blown
45
Error 044 Plate / Reflective Sensor Broken (Detected During Start Up)
45
Error 045 Plate / Reflective Sensor Broken (Calibration Failure)
46
Error 046 Incompatible Driver Version (FW Ver5.04 and Newer)
46
Error 047 Safety Switch Open (FW Ver5.05 and Newer)
46
Troubleshooting Without Actual Error Code Available
47
Error: Degraded Image Quality
47
Error: Shows Completely Blank Image
47
Error: Door Mechanism Related Errors
47
Error: Not Starting Image Readout When the Plate Is Inserted Properly or Starts Readout Without the Plate or Starts Readout Plate Wrong Way Round
48
Error: no Response While a Key Is Pressed
48
Error: Membrane Switch Panel LED DIM, Lit Constantly or Not Lit at All
48
Error: Unit Starts up by Itself after Plugging in the Power Cord
49
Error: Unit Goes to Standby-Mode by Itself During or after Startup
49
Troubleshooting Based on Image Errors
50
Improper Use of the Hygiene Accessories
50
Improper X-Ray Settings Used
50
Ghost Images, Shadows
50
Improper Aiming of the X-Ray
50
Unsharp / Blurred Images
51
Geometry Distortion
51
Decreased Contrast, Shadows/Shading, Ghost Images
51
White or Grey Dots/Spots/Stains in Images
51
Wearing of the Imaging Plates
51
Image Shows Different Size than the Ip Used
52
Circle on Image
52
Vertical Stripe(S)
52
Pmt Problems
52
Incorrect Dimensions
52
Triangular Artifact in the Left Bottom Corner of the Image
53
Appendix 1: Troubleshooting Errors 034, 035, 041 and 042
54
Appendix 2: Solution for Error 039 Log Amp Calibration Failure
57
Appendix 3: Solution for the Blank Image and "Degraded Image Quality
58
Appendix 4: Door and Plate Carrier Mechanism Movement Related Problems
59
Appendix 5: Test after Repair
61
Appendix 6: Pmt Filter Light Leak Check/Repair/Replacement
62
Advertisement
Advertisement
Related Products
Instrumentarium Orthoceph OC100 D
Instrumentarium Orthopantomograph OP100 D
Instrumentarium Categories
Dental equipment
Medical Equipment
More Instrumentarium Manuals
Login
Sign In
OR
Sign in with Facebook
Sign in with Google
Upload manual
Upload from disk
Upload from URL