FPT C13 ENS M33 Manuals

FPT C13 ENS M33 Manuals

Manuals and User Guides for FPT C13 ENS M33. We have 1 FPT C13 ENS M33 manual available for free PDF download: Technical And Repair Manual

FPT C13 ENS M33 Technical And Repair Manual

FPT C13 ENS M33 Technical And Repair Manual (240 pages)

Brand: FPT | Category: Engine | Size: 20 MB

Table of Contents

Overview

5
- Table of Contents
  5
- Identification Data
  7
- Identification Tag
  7
- Commercial Code
  8
- Product Model Number
  9
- Engine Parts and Components
  10
- Engine Architecture
  12
- Combustion Air Intake and Exhaust System
  14
- Air/Sea Water Heat Exchanger
  15
- Combustion Air Pre-Heating
  15
- Intake and Exhaust Assembly
  15
- Cooling Fresh Water Closed Loop
  16
- Tube Bundle Water/Water Heat Exchanger
  17
- Bypass Junction for Thermostatic Valve
  17
- Sea Water Open Cooling Loop
  18
- Sea Water Pump
  19
- Engine Oil - Lubrication Loop
  20
- Commutable Filters (on Request)
  21
- Pre-Lubrication System (on Request)
  21
- Oil Vapor Filter
  21
- Gear Pump
  21
- Fuel Lines
  22
- Hydraulic Schematic Diagram
  23
- Injection System - Edc
  24
- EUI Electrically Controlled Pumping Injector
  25
- Electrical and Electronic Components
  28
- System Functions
  30
- Reference Signals
  32
Electrical Equipment

41
- Overview
  43
- Synopsis
  44
- Wire Harness
  45
- Location of Electrical Components on Engine
  46
- Power Supply Line
  48
- Alternator
  49
- Electrical Starter Motor
  50
- Diagnosis Connector J1
  51
- Relay Box
  51
- Relays Contained in the Relay Box
  51
- RPM Control
  51
- Connections of the Central Electronic Unit (Ecu)
  52
- ECU Connector Removal and Insertion
  52
- Relay Box Connectors
  52
- Identification of Terminal Functions
  53
- Eui Solenoid Valve Connector
  54
- Through-Bulkhead E Connector
  54
- Low Temperature Starting Aid
  55
- Lubricating Oil Transfer Module
  55
- Optional Equipment
  55
- Pre-Lubrication and Oil Transfer Module
  55
- Pre-Lubrication System
  55
- Equipotential Connections to Engine Ground
  56
- Wiring Diagram
  57
- Wiring Diagram Key
  57
- Electrical Equipment Component Code
  58
- EDC Connector B
  60
- EDC Connector a
  61
- Main Analog Instrument Panel
  62
- Secondary Analog Instrument Panel
  63
- CAN - BUS Converter Module Interface Wiring
  64
- Supplementary Services Battery Recharge
  65
Section Diagnostics

67
- Anomalies Indicator Light
  70
- Blink Code
  70
- Diagnostics
  70
- Ecu Behaviour
  70
- Error Deletion Procedure
  70
- Recovery
  70
- Blink Code Table
  71
- Diagnosis with the Pt-01 Instrument
  72
- Functions of the Instrument
  72
- Identifier
  72
- Active Diagnostics
  73
- Fault Memory
  73
- Parameter Reading
  73
- Checking Pressure in Fuel Supply Line
  74
- Checking the Keying of Timing Phonic Wheel
  74
- Checking the Timing Phase
  74
- Major Diagnostic Actions
  74
- Venting the Fuel Loop
  74
- Checking Component Resistance Value
  75
- Checking Line Insulation
  75
- For Non Hardwired Sensors
  76
- Reference Values
  76
- Sensors Wired with Shielded Wires
  76
- Throttle Position Sensor
  76
- For Wired Sensors Powered by the ECU
  77
- Guide to Blink Code Diagnosis
  78
- Guide to Symptom Diagnosis
  84
Section

95
- Foreword
  97
- Prescriptions for Work on the Injection System and Its Components
  98
- EUI Disassembly
  99
- Replacing Belt
  99
- Replacing Eui Pumping Units
  99
- EUI Assembly
  100
- Rocker Arm Shaft Assembly
  100
- Venting the Air from the Fuel Feed Loop
  101
- Cleaning the Engine Coolant/Sea Water Heat Exchanger
  102
- Cleaning the Air/Sea Water Heat Exchanger
  103
- Adjusting Camshaft Phase
  104
- Adjustments
  104
- Checking the Timing Phase
  106
- Timing Shaft Phonic Wheel Keying
  106
- Flywheel Sensor Seat Position
  107
- Adjusting Valve Clearance and EUI Pump Position
  108
- Intake Side
  110
- Uncoupling Marine Parts
  110
- Exhaust Side
  111
- Handling
  112
- Instructions for Disembarking the Engine
  112
Section 10 Safety System for Homologated Installations

209
- Safety System for Homologated Installations
  211
- Unit Installed
  211
- Electronic Monitoring Unit
  212
- Sensors
  212
- Insulated Pole Power Network (Optional)
  213
- Wiring
  213
- Alternator
  214
- Electrical Starting Motor
  214
- Auxiliary EDC Electronic Unit
  215
- Synoptic
  216
- Wiring
  217
- Monitoring Unit
  218
- Function of JS Connection Terminals
  219
- Position of the Safety System Sensors
  220
- Coolant High Temperature Sensor (IA)
  222
- Drive Shaft Rev. Speed Sensor (BA)
  222
- Exhaust Gas Temperature Sensor (O)
  222
- Coolant Oil Temperature Sensor (S)
  223
- Engine Oil Low Pressure Sensor (WA)
  223
- Engine Oil Pressure Sensor (VA)
  223
- Fuel Pressure Sensor (VCA)
  224
- Engine Cut-Out Control Buttons (JEM)
  225
- Line Balancing Components
  225
- Electrical Diagrams from the Safety System
  226
- Wiring Unit JB - JC
  227
- EDC System - Connector B
  228
- Basic Operations
  229
- Method of Use of the Safety System Interface
  229
- Monitoring
  229
- Advanced Operations
  230
- Video Mode Setting
  230
- Maintenance Intervals Resetting
  231
- Maintenance Rates Monitoring
  231
- Alarms Management
  232
- Navigation Monitoring
  232
- Depth Monitoring (Echo Sounder)
  233
- Safety Behaviour
  233

Advertisement

Advertisement

Related Products

FPT Categories

Engine Power Tool

More FPT Manuals