Sign In
Upload
Manuals
Brands
Fluke Manuals
Test Equipment
6270A
Fluke 6270A Manuals
Manuals and User Guides for Fluke 6270A. We have
2
Fluke 6270A manuals available for free PDF download: Service Manual, Operator's Manual
Fluke 6270A Service Manual (144 pages)
Pressure Controller/Calibrator
Brand:
Fluke
| Category:
Test Equipment
| Size: 13.44 MB
Table of Contents
Table of Contents
3
Introduction
7
Contact Fluke Calibration
8
Safety Information
8
Symbols
9
The Product Manual Set
10
Specifications
10
Control Specifications
12
Pressure Measurement Specifications
12
PM200 Modules
13
PM600 Modules
14
Theory of Operation
15
Overview
15
Accessories
15
Pneumatic and Electrical Configuration
15
Pneumatic Interfaces
17
Over Pressure Protection
17
Electrical
19
Module Connector
20
PCA Overview
21
Communications / Firmware
22
System Boot
23
Software Upgrades
23
Maintenance
24
Access the Module Bay
24
PMM and PCM Removal
25
Clean the Exterior
27
Pressure Leakage Test (On-Board Diagnostics)
27
Fuse Replacement
28
Manifold Replacement
29
Repair and Replacement
31
Feet and Tilt Stands
31
Remove and Replace Handles
33
Top Panel
35
Module Guide Rails
36
Communications Tray
38
The CPU
39
PMM Dock Assembly
41
G- and B-Series Valves
45
Remove and Inspect the B-Series Valves
46
Install the B-Series Valves
49
Remove and Inspect the G-Series Valves
50
Install the G-Series Valves
50
Power Supply and Fan
51
Remove the Power Supply
52
Remove the Fan
54
Remove the Power Entry Module
55
Front Panel and Display Assembly
56
Remove Front-Panel Assembly
56
Remove Keypad PCA and Knob from the Front-Panel Assembly
58
Remove Display Components from the Display Panel Shell
60
Remove the Module Bay Latch Assembly
63
PCM Assembly
65
Replace the Control Valves
68
Inspect the Control Valves
70
PCM Supply, Test, Exhaust Sensor Alignment
72
Calibrate the Sensors
73
Supply Port (ATM and 3,000 Psi)
74
Exhaust Port (Hard Vacuum then ATM)
76
Calibration Sled and PMM
76
PM200 and PM600 Modules
78
PM600 Digital Barometer Optimization
79
Setup
79
Return to Service - Safety Validation Recommendations
81
Electrical
81
Pressure
81
Calibration Adjustment
82
Pm200
82
Pm600
83
Calibration and Adjustment Procedures
84
Required Equipment
84
Preliminary Operations
86
Setup
87
Module Calibration
90
Calibration of Modules in Chassis
90
Calibration of Modules in Calibration Sled
91
Calibration Tables
94
PM200 Calibration Definition
94
PM600 Calibration Definition
95
PM200 Test Definition Matrices
96
PM600 Test Definition Matrices
108
Calibration with COMPASS for Pressure
116
Troubleshooting
117
Reset Controller Settings
119
Diagnostics
119
System
120
Measure
120
Control
121
Leak Test
121
Remote Interface
122
Contamination Prevention System (CPS)
122
CPS Cleaning and Inspection
122
Separate the Lower and Upper Housing
126
Inspect and Replace the CPS Valves
128
Replacement Parts
130
Screw Torque
142
Advertisement
Fluke 6270A Operator's Manual (84 pages)
Pressure Controller/Calibrator
Brand:
Fluke
| Category:
Test Equipment
| Size: 6.6 MB
Table of Contents
Table of Contents
3
Introduction
7
Contact Fluke Calibration
7
Safety Information
8
Symbols
9
The Product Manual Set
9
Specifications
10
Control Specifications
12
Pressure Measurement Specifications
12
PM200 Modules
13
PM600 Modules
14
Unpack the Product
15
Product Placement
16
Connect to Mains Power
17
Mains Voltage
17
Access the Module Bay
18
PMM Installation
20
PCM Installation
22
Barometric Reference Module (BRM)
23
Rear-Panel Manifold Pressure Connections
23
SUPPLY Port
24
EXHAUST Port (Vacuum Pump if Required)
25
TEST Port
26
REF Port
26
VENT Port
27
Controller Settings (Setup Menu)
28
Setup Menu
28
Instrument Setup Menu
28
Instrument Settings Menu
29
Remote Port Menu
31
Front-Panel Features
33
Rear-Panel Features
35
Turn on the Product
37
Warm-Up
37
Main Menu
37
Operation
43
Operating Modes
43
Set Target Pressure (Setpoint)
43
Step Pressure up or down
43
Jog Pressure
44
Vent and Abort
44
Pressure Measurement
45
Pressure Control Settings
46
Control Modes
46
Dynamic Control Mode
46
Static Control Mode
47
Control Limits (Only for Static Control)
48
Stability Limit (Only for Static Control)
48
Slew Rate (Rate of Pressure Change)
48
Safety Limits
48
Upper Limit
48
Lower Limit
48
Auto Vent
48
Pressure Measurement Settings
48
Unit and Custom Units
49
Measurement Modes
50
Measurement Resolution
50
Module Selection
51
Autozero
51
Gauge Mode
51
Absolute Mode
51
Atmosphere
52
Head Height
52
Tasks
53
Leak Test
53
Switch Test
54
Exercise
54
Program
55
Purge (if CPS Installed)
55
Contamination Prevention System (CPS)
56
Install the CPS
57
CPS Use
57
Hc20
57
P3000
59
Test Port Insert
61
Disconnect the CPS
62
External Driver Communication
62
Configure the Driver
63
Driver Electrical Connections
65
External Isolation Valve
66
System Stacking
68
System Setup
68
Operation
70
Maintenance
72
Fuse Replacement
72
Clean the Exterior
73
Manifold Replacement
74
Reset Controller Settings
75
Diagnostics
75
System
75
Measure
76
Control
76
Remote Interface
77
Troubleshooting
77
Error Codes
80
User-Replaceable Parts and Accessories
82
Advertisement
Related Products
Fluke 6200
Fluke 6200-2
Fluke 6100B
Fluke 6109A
Fluke 686
Fluke 6055
Fluke 6135A/PMU
Fluke 6135A/PMUCAL
Fluke 62 MAX
FLUKE 620
Fluke Categories
Measuring Instruments
Test Equipment
Multimeter
Thermometer
Laboratory Equipment
More Fluke Manuals
Login
Sign In
OR
Sign in with Facebook
Sign in with Google
Upload manual
Upload from disk
Upload from URL