User Manuals: Eurotherm 3508 Temperature Controller

Manuals and User Guides for Eurotherm 3508 Temperature Controller. We have 2 Eurotherm 3508 Temperature Controller manuals available for free PDF download: Engineering Handbook, Manual

Eurotherm 3508 Engineering Handbook (262 pages)

process controllers

Brand: Eurotherm | Category: Controller | Size: 10 MB

Table of Contents
2
Chapter 1 Installation and Operation

11
And 3508 Ordering Code

12
How to Install the Controller

13
- To Install the Controller
  14
Electrical Connections

15
Standard Connections

16
- Digital I/O
  17
- Power Supply Connections
  18
Plug in I/O Module Connections

19
- Zirconia Probe Construction
  23
Digital Communications Connections

24
- Devicenet Wiring
  25
  - Profibus
    26
- I/O Expander (or Additional Digital Input)
  27
- Example Wiring Diagram
  28
Getting Started

29
- Quick Start Parameters
  31
To Re-Enter Quick Start Mode

34
Normal Operation

35
The Operator Buttons

36
To Set the Required Temperature (Setpoint)

37
Alarm Indication

38
Message Centre

39
- How to Edit Parameters
  40
- Programmer Summary
  41
- Alarm Summary
  43
- Control Summary
  44
Chapter 2 Access to Further Parameters

45
- To Select Different Levels of Access
  46
Access Parameter List

47
Chapter 3 Function Blocks

49
To Access a Function Block

50
- To Change the Value of a Parameter
  51
Navigation Diagram

52
Chapter 4 Function Block Wiring

53
Soft Wiring

54
Chapter 5 Instrument Configuration

62
- Options Available in the Instrument Configuration List
  63
Display Formatting

64
- Bar Graph (3504 0Nly)
  66
Instrument Diagnostics

67
Chapter 6 Process Input

69
- Input Types and Ranges
  71
- CJC Type
  72
- Display Units
  73
- PV Offset
  74
- PV Input Scaling
  75
Chapter 7 Logic Input/Output

77
Chapter 8 Aa Relay Output

81
- Example: to Wire the AA Relay to an Alarm
  82
Chapter 9 Module Configuration

83
Module Identification

85
Module Scaling

95
- Relay, Logic or Triac Output Scaling
  96
- Potentiometer Input Scaling
  97
Chapter 10 Io Expander

99
To Configure the Io Expander

100
Chapter 11 Alarms

101
Analogue Alarms

102
Digital Alarms

103
- How Alarms Are Indicated
  104
Alarm Parameters

105
- Example: to Configure Alarm 1
  106
Diagnostic Alarms

107
Bcd Input

109
- Example: to Wire a BCD Input
  110
- Digital Communications
  111
- Rs485
  112
Configuration Ports

113
Broadcast Master Communications

114
- Wiring Connections - Broadcast Communications
  115
Digital Communications Parameters

116
- Communications Identity
  117
Example 2: to Send Sp from the Master to Pv in a Slave

118
Ethernet

119
- Itools Setup
  120
Counters, Timers, Totalisers, Real Time Clock

121
- Counter Parameters
  122
Timers

123
- Off Delay Timer Mode
  124
- One Shot Timer Mode
  125
- Compressor or Minimum on Timer Mode
  126
- Timer Parameters
  127
Totalisers

128
Real Time Clock

130
Application Specific

131
- Temperature Control of an Environmental Chamber
  132
Humidity Parameters

133
Zirconia (Carbon Potential) Control

134
Zirconia Parameters

135
Example of Carbon Potential Control Connections

136
Input Monitor

137
Input Monitor Parameters

138
Chapter 17 Logic and Maths Operators

139
- Logic Operations
  140
- Logic Operator Parameters
  141
Eight Input Logic Operators

142
Maths Operators

143
- Math Operations
  144
- Math Operator Parameters
  145
- Sample and Hold Operation
  146
Eight Input Analog Multiplexers

147
Chapter 18 Input Characterisation

149
- Compensation for Sensor Non-Linearities
  150
- Input Linearisation Parameters
  151
Polynomial

152
Chapter 19 Load

155
Chapter 20 Control Loop Set up

157
Loop Parameters - Main

158
- Types of Control Loop
  159
Pid Control

160
- Integral Term
  161
- Loop Break Time
  162
- PID Parameters
  163
Tuning

164
- Manual Tuning
  165
- Tune Parameters
  166
Setpoint Function Block

167
- SP Tracking
  168
Output Function Block

170
- Power Feed Forward Enable
  173
- Output Limits
  174
- Effect of Control Action, Hysteresis and Deadband
  175
Chapter 21 Setpoint Programmer

177
Programmer Operating States

178
- Holdback (Guaranteed Soak)
  179
- Segment Types
  180
- Power Fail Recovery
  181
- Sync Mode
  182
Creating or Editing a Program

183
To Select, Run, Hold or Reset a Program

186
Chapter 22 Switch over

187
- Switch over Parameters
  188
Chapter 23 Transducer Scaling

189
- Strain Gauge
  190
Comparison Calibration

191
Transducer Scaling Parameters

192
- Parameter Notes
  193
Transducer Summary

194
Strain Gauge

195
Load Cell

196
- Comparison Calibration
  197
Chapter 24 User Values

199
Chapter 25 Calibration

201
- To Calibrate MV Range
  202
- To Save the New Calibration Data
  203
- Thermocouple Calibration
  204
- RTD Calibration
  205
Calibration Parameters

206
- Part no HA027988 Issue 3.0 Aug
  208
Chapter 26 Configuration Using Itools

209
Connecting a Pc to the Controller

210
Parameter Set up

211
Device Panel

212
User Pages Editor

213
- Style Examples
  214
Recipe Editor

216
- Recipe Menu Commands
  217
To Set up Alarms Using Itools

218
- Alarm Summary Page in Itools
  219
- To Customise Digital Alarm Messages
  220
Program Editor

221
- Event Outputs
  222
- Naming Programs
  223
Graphical Wiring Editor

224
- Using Function Blocks
  225
- Tooltips
  226
- Using Wires
  227
- Using Comments
  228
- Using Monitors
  229
- Colours
  230
- Other Examples of Graphical Wiring
  231
Cloning

233
Appendix A Parameter Index

235
Appendix B Safety and Emc Information

251
Appendix C Technical Specification

255
- All Analogue and PV Inputs
  256
- Analogue Input Module
  257
- Digital Input Modules
  258
- Control Functions
  259
- Advanced Functions
  260
Declaration of Conformity

261

Eurotherm 3508 Manual (4 pages)

Brand: Eurotherm | Category: Controller | Size: 1 MB

Eurotherm Categories

Controller Temperature Controller Voice Recorder Measuring Instruments DC Drives

More Eurotherm Manuals

User Manuals: Eurotherm 3508 Temperature Controller

Eurotherm 3508 Engineering Handbook (262 pages)

Table of Contents

Chapter 1 Installation and Operation

And 3508 Ordering Code

How to Install the Controller

Electrical Connections

Standard Connections

Plug in I/O Module Connections

Digital Communications Connections

Getting Started

To Re-Enter Quick Start Mode

Normal Operation

The Operator Buttons

To Set the Required Temperature (Setpoint)

Alarm Indication

Message Centre

Chapter 2 Access to Further Parameters

Access Parameter List

Chapter 3 Function Blocks

To Access a Function Block

Navigation Diagram

Chapter 4 Function Block Wiring

Soft Wiring

Chapter 5 Instrument Configuration

Display Formatting

Instrument Diagnostics

Chapter 6 Process Input

Chapter 7 Logic Input/Output

Chapter 8 Aa Relay Output

Chapter 9 Module Configuration

Module Identification

Module Scaling

Chapter 10 Io Expander

To Configure the Io Expander

Chapter 11 Alarms

Analogue Alarms

Digital Alarms

Alarm Parameters

Diagnostic Alarms

Bcd Input

Configuration Ports

Broadcast Master Communications

Digital Communications Parameters

Example 2: to Send Sp from the Master to Pv in a Slave

Ethernet

Counters, Timers, Totalisers, Real Time Clock

Timers

Totalisers

Real Time Clock

Application Specific

Humidity Parameters

Zirconia (Carbon Potential) Control

Zirconia Parameters

Example of Carbon Potential Control Connections

Input Monitor

Input Monitor Parameters

Chapter 17 Logic and Maths Operators

Eight Input Logic Operators

Maths Operators

Eight Input Analog Multiplexers

Chapter 18 Input Characterisation

Polynomial

Chapter 19 Load

Chapter 20 Control Loop Set up

Loop Parameters - Main

Pid Control

Tuning

Setpoint Function Block

Output Function Block

Chapter 21 Setpoint Programmer

Programmer Operating States

Creating or Editing a Program

To Select, Run, Hold or Reset a Program

Chapter 22 Switch over

Chapter 23 Transducer Scaling

Comparison Calibration

Transducer Scaling Parameters

Transducer Summary

Strain Gauge