User Manuals: ETOP ISA-E13 Single Board Computer

Manuals and User Guides for ETOP ISA-E13 Single Board Computer. We have 1 ETOP ISA-E13 Single Board Computer manual available for free PDF download: User Manual

ETOP ISA-E13 User Manual

ETOP ISA-E13 User Manual (118 pages)

Brand: ETOP | Category: Single board computers | Size: 2 MB

Table of Contents

Table of Contents
3
Introduction
9
Chapter 1

10
- Features & Specifications
  10
- Features
  11
- Specifications
  12
Chapter 2

15
- Jumper Setting & Connectors
  15
- Jumpers on the ISA-E13
  16
- Jumper Locations on the ISA-E13
  17
- JP1: LCD PANEL Power Selection
  18
- JP2: LCD PANEL Inverter Power Selection
  18
- JP3: CF Card Mode Selection
  18
- JP4: Redundant System Support Switch
  19
- JP5: COM1 RS232/RS485 Selection
  19
- JP6: COM2 RS232/RS485 Selection
  20
- JP7: Clear CMOS RAM Data
  20
- JP8: On-Board LAN
  21
- JP9: COM1 Power Selection
  21
- Connectors on the ISA-E13
  22
- Connector Locations on the ISA-E13
  23
- BACKLIGHT Connector
  24
- COM1 (RS485), COM2 (RS485) Serial Ports
  24
- COM1 Serial Port
  25
- COM2, COM 3, COM 4 Serial Ports
  25
- INT_VGA Connector
  26
- PS/2 Keyboard & Mouse Connector
  26
- CF-II (BOT) Connector
  27
- DC_IN (5V+12V) Connector
  28
- DC_IN(5V) Connector
  28
- DIO1 Connector
  28
- DIO2 Connector
  29
- Floppy Drive Connector
  29
- Front Panel Connector
  30
- Irda Connector
  31
- IDE1 Connector
  32
- INT_KBMS Connector
  33
- IDE2 Connector
  33
- LPT Connector
  34
- LAN Connector
  34
- LVDS_LCD Connector
  35
- USB12, USB34 Connectors
  35
- TTL_LCD Connector
  36
- VGA Connector
  36
Chapter 3 Bios Setup

37
- BIOS Introduction
  38
- Starting Setup
  38
- Main Menu
  39
- Amibios
  39
- Processor
  39
- System Memory
  40
- System Time
  40
- System Date
  40
- Mtbf
  40
- System Fault
  40
- Advanced
  41
- Board Configuration
  42
- IDE Configuration
  43
- On Bard PCI IDE Controller
  44
- Primary/Secondary IDE Master/Slave
  45
- Type
  45
- Lba/Large Mode
  46
- Block (Multi-Sector) Transfer
  47
- PIO Mode
  48
- DMA Mode
  49
- 32Bit Data Transfer
  51
- Hard Disk Write Protect
  52
- IDE Detect Time out (Sec)
  53
- ATA (PI) 80 Pin Cable Detection
  54
- Hard Disk Delay
  55
- On Board IDE Operate Mode
  56
- Not Program PIO Mode
  57
- Floppy Configuration
  58
- Floppy a
  58
- Floppy B
  58
- Super I/O Configuration
  59
- On Board Floppy Controller
  59
- Floppy Drive Swap
  59
- Serial Port 3 Address
  59
- Serial Port 4 Address
  59
- Serial Port4 Mode
  60
- Parallel Port Address
  61
- Parallel Port Mode
  62
- EPP Version
  62
- ECP Mode DMA Channel
  62
- Parallel Port IRQ
  62
- Remote Access Configuration
  63
- Remote Access
  63
- Serial Port Number
  64
- Serial Port Mode
  65
- Flow Control
  65
- Redirection after BIOS POST
  66
- Terminal Type
  66
- VT-UTF8 Combo Key Support
  67
- Sredir Memory Display Delay
  67
- USB Configuration
  68
- USB Port 0,1,2,3
  68
- Legacy USB Support
  69
- USB 2.0 Controller Mode
  70
- BIOS EHCI Hand-OFF
  70
- PCI /Pnp
  71
- Clear NVRAM
  72
- Plug & Play O/S
  73
- PCI Latency Timer
  74
- Allocate IRQ to PCI VGA
  75
- Palette Snooping
  76
- PCI IDE Bus Master
  77
- Off Board PCI/ISA IDE Card
  77
- Irq 3, 4, 5, 6, 7, 9
  79
- Irq10, 11, 12, 14, 15
  79
- DMA Channel 0, 1, 3, 5, 6, 7
  80
- Reserved Memory Size
  81
- Boot Setting
  82
- Boot Setting Configuration
  82
- Quick Boot
  83
- Quiet Boot
  84
- Add on ROM Display Mode
  85
- Boot up Num-Lock
  86
- PS/2 Mouse Support
  87
- Wait for 'F1' if Error
  88
- Hit 'DEL' Message Display
  89
- Interrupt 19 Capture
  90
- Beep Function
  91
- On Board Virtual Flash FDD
  91
- Boot Device Priority
  92
- St Boot Device
  92
- Nd Boot Device
  92
- Rd Boot Device
  92
- Security
  93
- Change Supervisor Password
  93
- Change User Password
  94
- Boot Sector Virus Protection
  95
- Chipset
  96
- North Bridge Configuration
  96
- DRAM Timing Setting by
  97
- CPU Speed Setting by
  97
- South Bridge Configuration
  98
- Forward to
  98
- ISA Configuration
  99
- ISA Clock
  99
- ISA 16 Bits I/O Wait-State
  99
- ISA 8Bits I/O Wait-State
  99
- ISA 16 Bits Memory Wait-State
  99
- ISA 8Bits Memory Wait-State
  99
- PWM Configuration
  100
- PUM Timer0
  100
- PUM Timer1
  100
- PUM Timer2
  100
- Serial/Parallel Port Configuration
  101
- SB Serial Port 1
  102
- Serial Port IRQ 1
  102
- Serial Port Bound Rate
  102
- PUM & COM2 PIN Select
  102
- SB Serial Port 2
  102
- Serial Port IRQ 2
  102
- Watchdog Configuration
  103
- Watch Dog 0 Signal Function
  103
- Watch Dog 0 Signal Select
  104
- GPIO Configuration
  105
- Gpio Porto 78H*07
  105
- Gpio Porto 79H*17
  105
- Gpio Porto 7Ah*27
  105
- PORT3 & SPI Pin Select
  105
- Gpio Port3 7Bh*37
  105
- PORT2& COM1 Pin Select
  106
- GPCS Configuration
  107
- GPCSO Function
  107
- GPCS1 Function
  107
- Redundancy Control Configuration
  108
- Dual Port 4KB SRAM
  108
- SB Serial Port 9
  108
- Watvhdog0 Condition
  108
- Watvhdog1Condition
  108
- Invalid OPCODE Condition
  108
- KB/MS System Fail
  108
- GPIO PORT0 System Fail
  109
- GPIO PORT1 System Fail
  109
- GPIO PORT2 System Fail
  109
- LPT PORT System Fail
  109
- UART1 System Fail
  109
- UART2 System Fail
  109
- UART3 System Fail
  109
- UART4 System Fail
  109
- Exit Option
  110
- Save Changes and Exit
  111
- Discard Changes and Exit
  112
- Discard Changes
  113
- Load Optimal Defaults
  113
- Load Failsafe Defaults
  114
Chapter 4 Appendix

115
- I/O Port Address Map
  116
- Interrupt Request Lines (Irq)
  117
- Post Beep
  118

Advertisement

Advertisement

Related Products

ETOP Categories

Single board computers Motherboard Computer Hardware

More ETOP Manuals