Alliance Laundry Systems UWN065T4L Manuals

Manuals and User Guides for Alliance Laundry Systems UWN065T4L. We have 2 Alliance Laundry Systems UWN065T4L manuals available for free PDF download: Programming Manual, Installation Operation & Maintenance

Alliance Laundry Systems UWN065T4L Programming Manual (82 pages)

Washer-Extractor Pocket Hardmount UniLinc Control

Brand: Alliance Laundry Systems | Category: Washer | Size: 0 MB

Unilinc Control
1
Table of Contents
3
Safety Information
7
Explanation of Safety Messages
7
Important Safety Instructions
7
Safety Decals
9
Operator Safety
10
Introduction
11
Model Identification
11
Nameplate Location
12
Replacement Parts
12
Customer Service
12
Preliminary Information
13
About the Control
13
- Power Failure Recovery
  13
- IR Communications
  13
- Network Communications
  13
- Audit Information
  13
- IR Communications Menu
  14
- IR Communications Error Menu
  14
- Restore to Factory Defaults
  14
- Entering Program Mode
  15
Unilinc Identification
16
Operational Keypad
16
Operation Modes
17
- General Modes of Operation
  17
- Power-Up Mode
  17
- Idle Mode
  17
- Door Locking Mode
  17
- Run Mode
  17
- Stop Mode
  17
- Door Unlocking Mode
  17
- Error Mode
  17
- Delayed Start Countdown Mode
  17
Machine Cycle Definition and Operation
18
Machine Cycle Operation
18
Delayed Start Feature
18
Cycle Menu
18
- To Start a Cycle
  19
Run Menu
20
Contrast/Backlight Menu
22
Close Door Menu
22
Lubricate Bearings Menu
23
Run Diagnostic Menu
23
Speed, Temp and Water Level Menu
24
Cycle Aborted Retry Menu
24
Error Menu
25
Cycle Stopped Menu
25
Delayed Start Menu
25
Cycle Aborted Fatal Menu
25
Delayed Start Countdown Menu
26
Delayed Start Final Countdown Menu
26
Menu Navigation
27
The Unilinc
27
Menu Navigation on a Single Screen
27
Menu Navigation with Parameters
27
Screen to Screen Navigation Using the Arrow Keypads
27
Navigation in String Edit Mode
27
Display Screen Maps
28
- System Menu Map Tree
  28
- Run Menu Map Tree
  29
- Service Menu Map Tree
  29
Programming Unilinc
30
System Menu
30
Save Changes Menu
30
Program Menu
31
Modify Cycle
31
- Available Characters
  32
Cycle, Segment and Step Programming Flow Diagram
33
- Step Menu Navigation
  33
- Reuse Fill Step Menu
  34
- Fill Step Menu
  35
- Heater Option
  36
- Supply a and B Step Menu
  36
- Agitate Step Menu
  37
- Cool down Step Menu
  37
- Drain Step Menu
  38
- Spray Rinse Extract Step Menu
  38
- Extract Step Menu
  39
- General Purpose Signals Menu
  39
- End of Segment Audio Signal Step Menu
  40
Global Setup
41
Global Setup Menu
41
Language Menu
41
Date/Time Menu
41
Water Level Menu
42
Temperature Menu
42
Audio Menu
43
Balance Retry Menu
43
Water Management Menu
44
Alarms Program Menu
46
Rapid Advance Menu
46
Banners Menu
47
Factory Defaults Menu
47
Shakeout Menu
47
Water Level Confirmation Menu
48
Water Temperature Confirmation Menu
48
Alarms Confirmation Menu
48
Audio Confirmation Menu
49
Reset All Factory Defaults Confirmation Menu
49
Factory Defaults Second Confirmation Menu
49
Diagnostic
50
Diagnostic Menu
50
- Drive ID Menu
  50
- Drive Alarms Menu
  50
Test Menu
50
- Test Cycle
  51
Factory Valve Purge Menu
53
Inputs Outputs Menu
53
Water Leak Detection Diagnostic
55
Drive Test
55
Alarms
56
Machine Identification
57
Machine Errors
57
- Door Lock Error
  57
- Door Open Error
  57
- Drain Alarm Error
  57
- Fill Alarm Error
  57
- Frame Balance Switch Error
  58
- Open Temperature Sensor Error
  58
- Shorted Temperature Sensor Error
  58
- SPI Error
  58
- Unbalance Error
  58
- Heat Alarm Error
  58
- Water Level Sensor Error
  59
- IR Communications Error
  59
- Network Communications Error
  59
- Water Leak Detection Error
  59
- Slow Drain Detected During a Machine Cycle Error
  60
- Drive SPI Error
  60
- DC Bus Error
  60
- No Tachometer Error
  60
- Locked Rotor Error
  60
- Shorted IGBT Error
  60
- IPM Overtemperature Error
  61
- Invalid Parameter Set Error
  61
- Maximum Current Exceeded Error
  61
- Current Sensor Error
  61
- Low DC Bus Error
  61
- Invalid Command Error
  61
- Last Drive Error
  61
Laundry Management
62
Total Number of Machine Cycle Counters
63
Total Number of Operating Minutes Counters
63
Last 10 Machine Cycles Rapid Advanced or Stopped
63
Maintenance
64
Service Schedule Menu
64
- Daily Menu (Service)
  64
- Weekly Menu (Service)
  64
- Monthly Menu (Service)
  65
- Quarterly Menu (Service)
  65
Cycle Charts
66

Alliance Laundry Systems UWN065T4L Installation Operation & Maintenance (56 pages)

Pocket Hardmount UniLinc and M30 Control

Brand: Alliance Laundry Systems | Category: Washer | Size: 3 MB

Table of Contents
3
Safety Information

5
Introduction

8
Specifications and Dimensions

10
Operation

43
- Operating Instructions for Unilinc Control
  43
  - Shakeout Routine
    44
- Operating Instructions for M30 Control
  45
  - Shakeout Routine
    46
Start up

47
- Basket Rotation
  47
  - Safety Out-Of Balance Switch Operation
    47
Maintenance

48
- Daily
  49
  - Beginning of Day
    49
  - End of Day
    49
- Weekly
  49
- Monthly
  50
- Quarterly
  51
- F8410701 (EN) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
  51
- Care of Stainless Steel
  52
Disposal of Unit

53

Alliance Laundry Systems Categories

Washer

Dryer Washer/Dryer Iron Finishers

More Alliance Laundry Systems Manuals

Alliance Laundry Systems UWN065T4L Manuals

Alliance Laundry Systems UWN065T4L Programming Manual (82 pages)

Table of Contents

Alliance Laundry Systems UWN065T4L Installation Operation & Maintenance (56 pages)

Table of Contents

Safety Information

Introduction

Specifications and Dimensions

Operation

Start up

Maintenance

Disposal of Unit

Related Products

Alliance Laundry Systems Categories