Agilent Technologies G4204A Manuals

Manuals and User Guides for Agilent Technologies G4204A. We have 1 Agilent Technologies G4204A manual available for free PDF download: User Manual

Agilent Technologies G4204A User Manual

Agilent Technologies G4204A User Manual (302 pages)

Infinity Quaternary Pump

Brand: Agilent Technologies | Category: Laboratory Equipment | Size: 6.76 MB

Table of Contents

Table of Contents

5
- Introduction Features
  
  10
  - Overview of the Quaternary Pump
    11
  - Operating Principle
    12
  - Operating Principle
    13
  - Positions of the Multi Purpose Valve
    14
  - Positions of the Multi Purpose Valve
    15
  - System Overview
    19
  - System Overview
    20
- Site Requirements and Specifications
  
  23
  - Site Requirements
    24
  - Physical Specifications
    27
  - Performance Specifications
    28
3 Installing the Module

31
4 Using the Pump

51
- Leak and Waste Handling
  52
- Preparing the Pump
  53
- Algae Growth in HPLC Systems
  54
  - How to Prevent And-Or Reduce the Algae Problem
    54
- Setting up the Pump with the Instrument Control Interface
  55
  - Overview
    55
  - Instrument Configuration
    56
  - The Pump User Interface (Dashboard Panel)
    58
  - Control Settings
    61
  - Method Parameter Settings
    63
- Priming the Pump
  68
- Flushing the Filter
  70
- Solvent Information
  72
5 How to Optimize the Performance of Your Module

79
6 Troubleshooting and Diagnostics

89
7 Error Information

95
- What Are Error Messages
  97
- General Error Messages
  98
  - Timeout
    98
  - Shutdown
    98
  - Remote Timeout
    99
  - Lost CAN Partner
    99
  - Leak Sensor Short
    100
  - Leak Sensor Open
    100
  - Compensation Sensor Open
    101
  - Compensation Sensor Short
    101
  - Fan Failed
    102
  - Leak
    102
- Pump Error Messages
  103
  - Pressure of Quaternary Pump above Upper Limit
    103
  - Pressure below Lower Limit
    103
  - Target Pressure Not Reached for Quaternary Pump Degasser
    104
  - Solvent Counter Exceeded Limit
    104
  - Waste Counter Limit Exceeded
    105
  - Flow Rate Limit Exceeded
    105
  - Quaternary Pump Shutdown During Analysis
    106
  - Reading the Pump Encoder Tag Failed
    106
  - Writing the Pump Encoder Tag Failed
    107
  - Pump Drive Blocked or Encoder Failed
    107
  - Drive Current too Low
    108
  - Drive Current too High
    108
  - Drive Timeout
    109
  - Overcurrent of Pump Drive
    109
  - Deliver Underrun
    110
  - Defect Connection between Main Board and Pump Drive Encoder
    110
  - Pump Drive Encoder Defect
    110
  - Multi Purpose Valve Failed
    111
  - Reading of Multi Purpose Valve Tag Failed
    111
  - Pump Drive Encoder Rollover
    111
  - Drive Position Limit
    112
  - Insufficient Power of Drive Encoder LED
    112
  - Drive Encoder Error
    112
  - Writing the Multi Purpose Valve Tag Failed
    113
  - Unknown Multi Purpose Valve Type
    113
  - Pump Drive Encoder Error
    113
  - Pump Drive Error
    114
  - Maximum Stroke Is too Short
    114
  - Pump Drive Stop Not Found
    115
  - Timeout: Wait for Composition
    115
  - Timeout: Wait for Run Volume
    116
  - Timeout: Wait for Volume
    116
  - Timeout: Wait for Flow
    117
  - Timeout: Wait for Pressure
    117
  - Drive Encoder Failed
    118
  - Drive Phases Differ too Much in Electric Resistance
    118
  - Degasser's Pressure Limit Violation
    118
  - Seal Wash Pump was Missing When Tried to Turn on
    119
  - Valve Hardware Overcurrent (MCGV)
    119
- Test Functions and Calibrations
  121
9 Maintenance

123
- Introduction to Maintenance
  125
- Warnings and Cautions
  126
- Overview of Maintenance
  128
- Cleaning the Module
  129
- Installing Fittings and Capillaries
  130
- Replacing the Pressure Sensor
  131
- Replacing the Inlet Weaver
  134
- Replacing the Inlet Valve
  136
- Replacing the Outlet Valve
  137
- Removing the Jet Weaver
  139
- Installing the Jet Weaver
  141
- Replacing the Seal Wash Pump
  143
- Replacing the Multi-Channel Gradient Valve (MCGV)
  145
- Releasing a Stuck Inlet Valve
  149
- Replacing the Pump Head
  152
- Disassembling the Pump Head
  158
- Disassembling the Primary Pump Head
  160
- Disassembling the Secondary Pump Head
  164
- Replacing the Heat Exchanger
  168
- Replacing Wash Seal and Gasket
  171
- Assembling the Pump Head
  173
- Replacing the Multi Purpose Valve
  185
- Replacing Parts of the Multi Purpose Valve
  188
- Replacing the Outlet Filter
  189
- Replacing Parts of the Inline Filter
  191
- Installing the Valve Rail Kit
  194
- Replacing Module Firmware
  195
- Preparing the Pump Module for Transport
  196
10 Parts and Materials

201
- Overview of Main Assemblies
  202
- Flow Connections
  204
- Seal Wash Option
  206
- Pump Head Assembly Parts
  207
- Primary Pump Head Parts
  208
- Secondary Pump Head Parts
  212
- Multi Purpose Valve
  216
- Solvent Cabinet
  218
- Cover Parts
  220
- Leak Parts
  222
- Accessory Kit
  224
- Others
  225
  - HPLC System Tool Kit
    225
  - 1290 Infinity Pump Service Kit
    226
11 Identifying Cables

227
- Cable Overview
  228
- Analog Cables
  230
- Remote Cables
  232
- BCD Cables
  235
- CAN/LAN Cable
  237
- RS-232 Cable Kit
  238
- Agilent 1200 Module to Printer
  239
12 Hardware Information

241
- Firmware Description
  242
- Electrical Connections
  245
  - Rear View of the Module
    246
- Interfaces
  247
  - Overview Interfaces
    250
- Setting the 8-Bit Configuration Switch
  254
  - Special Settings
    256
- Early Maintenance Feedback
  257
- Instrument Layout
  258
13 LAN Configuration

259
- What You Have to Do First
  260
- TCP/IP Parameter Configuration
  261
- Configuration Switch
  262
- Initialization Mode Selection
  263
- Dynamic Host Configuration Protocol (DHCP)
  267
  - General Information (DHCP)
    267
- Setup (DHCP)
  268
- Link Configuration Selection
  270
- Automatic Configuration with Bootp
  271
  - About Agilent Bootp Service
    271
- How Bootp Service Works
  272
- Situation: Cannot Establish LAN Communication
  272
- Installation of Bootp Service
  273
- Two Methods to Determine the MAC Address
  275
- Assigning IP Addresses Using the Agilent Bootp Service
  276
- Changing the IP Address of an Instrument Using the Agilent Bootp Service
  279
- Manual Configuration
  281
- With Telnet
  282
- With the Instant Pilot (G4208A)
  286
- PC and User Interface Software Setup Setup
  287
  - PC Setup for Local Configuration
    287
- User Interface Software Setup
  288
- Appendix
  289
  - General Safety Information
    290
  - The Waste Electrical and Electronic Equipment (WEEE) Directive (2002-96-EC)
    293
  - Radio Interference
    294
  - Sound Emission
    295
  - Agilent Technologies on Internet
    296
  - Features
    299

Advertisement

Advertisement

Related Products

Agilent Technologies Categories

Measuring Instruments Laboratory Equipment Test Equipment Water Pump

Power Supply

More Agilent Technologies Manuals