DSHG Headset Operation ........................18 Upload Ringtones ..........................18 Setup ASIP via Browser ........................19 Network Setting of ST 40 IP via Browser .................... 20 ST 40 IP Firmware Update ........................21 Default Settings ........................... 22 Reset to Default ........................... 22 Copyright .............................
STE 40 Console Untangler Connection The ST 40 IP handset offers a compartment for the connection of a cord untangler. As the optional untangler is fitted inside the handset it will not interfere in normal use or when the receiver is put back on hook.
Connection Connect the RJ 45 plug of the line cord of your ST 40 IP into a network socket which is connected to your network. Please note that the LAN module 508 / 510 must be part of this network.
System Telephone ST 40 IP ST 40 IP Buttons Softkeys Adjustable Graphic Display Speaker 10 Function But- (below tons with LED's handset) Function Button Label Insert Microphone Numeric Keypad Message Waiting LED - Flashes on new entry in the call log or missed call.
System Telephone ST 40 IP Display Area of ST 40 IP Display in WK26 Tu 11.Jul.06 11:59 Activated features standby: *${}%“S are shown here Internal and Status of analogue external S0 Status, trunk lines one box per S0. 12 14 16 Current function of soft keys below.
System Telephone ST 40 IP Function Buttons - Freely programmable Function Buttons (overview) TAM activation To switch the answering machine of an ST31/ST 40 on or off. Reject Reject an incoming call. Caller will hear busy tone. AIS Volume Volume adjustment of AIS announcements via an external speaker.
Page 9
System Telephone ST 40 IP Function Buttons - Freely programmable Function Buttons (overview) Speaker Adjust speaker volume for handsfree or on hook use. Volume Set or cancel Least Cost Routing (LCR) for your System Phone. Line Display line status and directly access an external line.
System Telephone ST 40 IP LED - Display for freely programmable function buttons LED on LED off LED flashes Call Waiting activation enabled disabled Call Log Call Log entries No numbers in New Numbers in Call already viewed Call Log...
Page 11
System Telephone ST 40 IP LED - Display for freely programmable function buttons LED on LED off LED flashes LED flashes (slowly) (fast) TAM switched TAM Activation TAM switched Extension Button Extension is The button is Exclusive hold busy or off hook...
System Telephone ST 40 IP Button Assignment Announce Call Waiting In default all programmable buttons of the system phones are set System Memory System Memory identically. Tone Call Appointment System Memory System Memory These buttons can be individual programmed to suit your specific...
System Telephone ST 40 IP Call Waiting First Option: You are on a call and End current call Waiting call will ring Lift handset Talk your phone hear the call waiting tone Second Option: Press „SPLIT“. The first call is placed on hold while the waiting one is connected to you. You can alter between the calls by pressing the Split Button.
System Telephone ST 40 IP Display Call Log The flashing message waiting button will indicate that there is one entry in the call log. With the receiver on hook press the message waiting button. The last missed call will be displayed giving telephone number, date and time.
System Telephone ST 40 IP Phonebook (Vanity retrieval) Press Enter the desired letter,ie.A =2.The Select the next letter,ie.N Lift handset or press the Phonebook first entry with the selected initial =6.The first entry handsfree button, button letter is displayed. with “An ”is displayed.
ST 40 IP Location Select a suitable location for the ST 40 IP to be installed. Please observe the following points: - Do not use locations where the phone could be subjected to water or chemicals. - Rubber feet of the Phone: Your phone has been manufactured for general use.
- insert the headset plug into the headset socket until you hear a positive click. - lay the cable in the cable duct underneath the ST 40 IP which is also used as a strain relief - to unplug the cable, release the latch on the plug (use a small screw driver if required) and at the same time pull the plug out of the socket.
ST 40 IP DSHG Headset Operation Please program a headset button for the ST 40 IP or STE 40 either via TK Suite Basic or the system programming code XX 31. - You now will be able to answer or clear a call from the headset.
System Telephone ST 40 IP Setup ASIP via Browser It is possible to allocate the ST 40 IP to a LAN Module 508 / LAN Module 510 via the Browser. To do this please call up the following page „http://Telefon-IP/tkset“. Important:...
ST 40 IP Network Setting of ST 40 IP via Browser Important network setting of the ST 40 IP can be carried out via the browser. To do this call up the page „http://Telefon-IP/Tkset“and click on the tab „LAN Settings“.
ST 40 IP ST 40 IP Firmware Update Your ST 40 IP System Phone can be updated to the latest firmware version without hardware intervention. Your qualified dealer will be able to download new firmware from www.agfeo.com and upload this into your ST 40 IP.
System Telephone ST 40 IP Default Settings IoP Name: „St40IP-xxxx“ („xxxx“ are the last 4 digits of the Mac Address of the ST 40 IP) DHCP: Client IP-Address: 0.0.0.0 0.0.0.0 Subnet Mask: Gateway: 0.0.0.0 DNS1: 0.0.0.0 DNS2: 0.0.0.0 Server: 192.168.100.1...
Technical Changes The information contained in this manual is subject to change without prior notice. AGFEO GmbH & Co. KG will not accept any responsibiltiy for any errors that may occur in this document. We aim not to include typographical errors or inaccuracies and have taken great care in the preparation of this document.
Page 24
Ident no. 1102021 Subject to change without prior notice. No AGFEO GmbH & Co. KG liability can be accepted for errors contained in Gaswerkstr. 8 this document.