Related Manuals for Versitron S72450
Summary of Contents for Versitron S72450
- Page 1 S72450 24-port 10/100 Switch Installation Guide Copyright July 2003 VERSITRON, Inc. 83 Albe Drive / Suite C Newark, DE 19702 www.versitron.com B030730359450...
- Page 2 The information contained in this document is subject to change without prior notice. Copyright VERSITRON. All Rights Reserved. TRADEMARKS All brand names are trademarks or registered trademarks of their respective holders. WARNING: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
- Page 3 All VERSITRON products are warranted for a period of one year from date of delivery. VERSITRON reserves the right to repair or, at our option, replace parts which during normal usage prove to be defective during the warranty period provided that: 1.
-
Page 4: Table Of Contents
3.1 Connecting Devices to the 24-port Switch..........3 3.2 Connecting to Another Ethernet Switch/Hub........3 3.3 Application Example ................4 For 100BaseFX Connection..............5 4.1 Adding 100BaseFX Module..............5 LEDs Conditions Definitions ............6 5.1 LEDs Defined..................6 Configure from Console ..............7 6.1 Hardware Setting for Console.............7 6.2 Operation in Console................7 www.versitron.com... -
Page 5: Introduction
1. Introduction The Model S72450 24-port Switch is a 24-port 10/100Mbps Fast Ethernet switch. This switch supports the advanced features for current switch design. This switch can auto detect 10/100Mbps speed, full/half duplex mode, MDI/MDI-X connection and provides an option for one 100BaseFX expansion module port. -
Page 6: Installation
There is sufficient space surrounding the switch to allow for proper ventilation (the switch may not function according to specifications beyond the temperature range of 0 to 50 degrees C). You can also install this 24-port Switch in a 19" rack with the rack-mount kits as shown below: www.versitron.com... -
Page 7: Configure The Network Connection
TP ports on the 24-port Switch are Auto MDI/MDI-X, you can connect from any TP port of the 24-port Switch to the MDI or MDI-X port of another hub/switch with Straight Through or crossover cables. Max 100m/328ft TO: MDI or MDI-X port www.versitron.com... -
Page 8: Application Example
The example below demonstrates the switch ability to segment the network. The number of nodes on each segment is reduced thereby minimizing network contention (collisions) and boosting the available bandwidth per port. Another Ethernet Switch Hub/Switch Hub/Switch Power User Workgroup Workgroup www.versitron.com... -
Page 9: For 100Basefx Connection
4. Tighten the screws of the module to the switch. 5. Connect the fiber optic cable to the FX port of the module. 6. Power on the switch. 7. Refer to Section 6 to configure Port 24 to (Auto-Disable, 100Mbps, Full duplex) for 100BaseFX connection from the console. www.versitron.com... -
Page 10: Leds Conditions Definitions
Data packets being received or sent. Link / Act Green Connection speed is 100Mbps. Yellow Connection speed is 10Mbps. Connection is Full Duplex. FDX / Col Packet collisions occurring. A low level of Flashing collision is a part of normal Ethernet Operation. www.versitron.com... -
Page 11: Configure From Console
There is only one item in this function. You can enable or disable the backpressure function for half-duplex. If it is enabled, it can prevent packets lost in half-duplex mode. But it will also reject packets when the network traffic is very heavy and that may cause some network connections to fail. www.versitron.com... - Page 12 VLAN, the removed port from VLAN will be assigned to Group 24 automatically if it does not belong to any VLAN any more after being removed. In the setting, VLAN groups can be overlapped on ports in this switch. www.versitron.com...
- Page 13 VLAN Based: If the setting of a port is set to E then tagged packets received from this sport will be forwarded with a the priority information in the tag. 5. Restore Default Setting : You can restore to the default setting of the switch with this function. www.versitron.com...
- Page 14 Humidity 5% to 95% (Non-condensing) Network Bridging Function Filtering, forwarding and learning Switching Method Store-and-forward Address Table 8K entries Filtering/Forwarding Rate Line speed VLAN 24 groups max., configured from console 2 transmit queues per port Priority Port-Based or Tagged-Based www.versitron.com...
- Page 15 Green ---- ---- 2 Green White-Orange ---- ---- 3 White-Orange Not Used Blue Not Used Blue Not Used White-Blue Not Used White-Blue Orange ---- ---- 6 Orange Not Used White-Brown Not Used White-Brown Not Used Brown Not Used Brown www.versitron.com...
-
Page 16: Emi Certification
1kV - (power line), 0.5kV - (signal line) This product complies with the requirements of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC. Warning! Do not plug a phone jack connector in the RJ-45 port. This may damage this device. www.versitron.com...
Need help?
Do you have a question about the S72450 and is the answer not in the manual?
Questions and answers