Epson TM-T70-i Technical Reference Manual
  1. Manuals
  2. Brands
  3. Epson Manuals
  4. Printer
  5. OmniLink TM-T70-i
  6. Technical reference manual

Epson TM-T70-i Technical Reference Manual

Hide thumbs Also See for TM-T70-i:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual, Technical Reference Manual
Technical Reference Guide
Product Overview
Describes features and general specifications for the product.
Setup
Describes setup and instrallation of the product and peripherals.
Application Development Information
Describes how to control the printer and necessary information
when you develop applications.
Handling
Describes how to handle the product.
Appendix
Describes character code tables.
M00041503
Rev. D

Advertisement

Table of Contents
loading

Related Manuals for Epson TM-T70-i

Summary of Contents for Epson TM-T70-i

  • Page 1 Technical Reference Guide Product Overview Describes features and general specifications for the product. Setup Describes setup and instrallation of the product and peripherals. Application Development Information Describes how to control the printer and necessary information when you develop applications. Handling Describes how to handle the product.
  • Page 2 • Neither is any liability assumed for damages resulting from the use of the information contained herein. • Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation’s operating...

  • Page 3: For Safety

    For Safety Key to Symbols The symbols in this manual are identified by their level of importance, as defined below. Read the following carefully before handling the product. You must follow warnings carefully to avoid serious bodily injury. WARNING Provides information that must be observed to prevent damage to the equipment or loss of data.

  • Page 4: Warnings

     Shut down your equipment immediately if it produces smoke, a strange odor, or unusual noise. Continued use may lead to fire. Immediately unplug the equipment and contact your dealer or a Seiko Epson service center for advice.  Never attempt to repair this product yourself. Improper repair work can be dangerous.

  • Page 5: Cautions

    Cautions  Do not connect cables in ways other than those mentioned in this manual. Different connections may cause equipment damage or fire.  Be sure to set this equipment on a firm, stable, horizontal surface. CAUTION The product may break or cause injury if it falls. ...

  • Page 6: Wireless Lan (Ot-Wl01) Important Safety Information

    Tampering with this product may result in injury or fire.  OT-WL01 is only for indoor use.  OT-WL01 should only be used for EPSON TM Intelligent Printers. If it is installed on another device, it may result in computer failure, damage, or CAUTION malfunctions.
  • Page 7 Notes on Security when Using Wireless LAN (Important information on customer rights (maintaining privacy) The advantage of using a wireless LAN over a LAN cable is that, because information is exchanged using radio signals, you can easily connect to the network if you are within range of the radio signals.

  • Page 8: Restriction Of Use

    Restriction of Use When this product is used for applications requiring high reliability/safety such as transportation devices related to aviation, rail, marine, automotive etc.; disaster prevention devices; various safety devices etc.; or functional/precision devices etc., you should use this product only after giving consideration to including fail-safes and redundancies into your design to maintain safety and total system reliability.

  • Page 9: About This Manual

    About this Manual Aim of the Manual This manual was created to provide information on development, design, and installation of receipt issue systems and development and design of printer applications for developers. Manual Content The manual is made up of the following sections: Chapter 1 Product Overview Chapter 2...

  • Page 10: Table Of Contents

    Contents ■ For Safety ..........................3 Key to Symbols............................3 Warnings ..............................4 Cautions ..............................5 Wireless LAN (OT-WL01) Important Safety Information ...............6 Wireless LAN (OT-WL01) Usage Precautions ..................6 ■ Restriction of Use ........................8 ■ About this Manual ........................ 9 Aim of the Manual ..........................9 Manual Content .............................9 Product Overview ................15 ■...
  • Page 11 TM-T70-i Dedicated AC Adapter ....................... 34 ■ Option Specifications......................35 Wireless LAN Cable Set (OT-WL01) ..................... 35 Setup .....................37 ■ Flow of Setup ........................37 ■ Installing the Printer ......................38 Important Notes on Installation......................39 Affixing Position of DF-10........................39 ■ Setting the DIP Switches .....................40 Setting Procedure ..........................
  • Page 12 Starting EPSON TMNet WebConfig .....................72 General Information..........................73 TCP/IP Information (Wired) ........................74 TCP/IP Information (Wireless).......................75 Web Contents Update Information....................76 Time Information ...........................77 Wired Setting............................78 TCP/IP Setting (Wired) ..........................79 Wireless Setting .............................80 TCP/IP Setting (Wireless)........................81 Device Settings .............................82 Web Contents Update Settings ......................83 Administrator Setting ..........................85...

  • Page 13: Product Overview

    Chapter 1 Product Overview Product Overview This chapter describes features and specifications of the product. Features ePOS-Print system • Direct printing from an application via network is possible. High speed printing • Issuing of batch receipts is possible. • Maximum print speed: 170 mm/s •...

  • Page 14: Product Configuration

    Others • Development kits such as MSDN are not required for application development. • Registering web pages on the TM-T70-i makes them accessible on the Web. • Methods to efficiently construct multiple systems are included. For details, see the "TM-i series Easy Setup Guide".

  • Page 15: Parts Name And Function

    CAUTION Power Switch Cover Install the power switch cover that comes with the TM-T70-i onto the printer to prevent inadvertent changing of the power switch, to prevent tampering, and to improve the appearance of the printer. To reset the printer when the power switch cover is installed, insert a long, thin object (such as the end of a paper clip) into the hole in the power switch cover and press the power switch.

  • Page 16: Control Panel

    Control Panel FEED button PAPER OUT LED ERROR LED (POWER) LED FEED button Pressing this button once feeds the roll paper by one line. Holding this button down feeds the roll paper continuously. PAPER OUT LED • Lights when there is no more roll paper or there is little remaining. •...

  • Page 17: Connectors

    Chapter 1 Product Overview Connectors All cables are connected to the connector panel on the lower rear of the printer. Micro-USB (AB type) Ethernet connector connector (for setting) Connector for DC 5V Drawer kick-out connector Power supply connector for DC 24V USB connectors (only for options) •...

  • Page 18: Push Button

    Push Button The push button on the lower rear of the printer prints a status sheet or initializes the printer. Push button • Status sheet printing: Make sure that the printer is turned on, press the push button for approximately 3 seconds. When you release the button, a status sheet on which network parameters are printed will be ejected.

  • Page 19: Error Status

    Chapter 1 Product Overview Error Status There are three possible error types: automatically recoverable errors, recoverable errors, and unrecoverable errors. Check the error codes. When connection to external devices fails, check the status LEDs at the lower rear of the printer. Automatically Recoverable Errors Printing is no longer possible when automatically recoverable errors occur.

  • Page 20: Unrecoverable Errors

    Unrecoverable Errors Printing is no longer possible when unrecoverable errors occur. The printer must be repaired. Turn off the power immediately when unrecoverable errors occur. CAUTION Error LED flash code Error Error description Approx. 160 ms Memory R/W error After R/W checking, the printer does not work correctly.

  • Page 21: No Connection To External Devices

    Chapter 1 Product Overview No Connection to External Devices When connection to external devices is not possible, check the status LED at the back of the printer. Status LED Orange: Booting Green: Operating normally When the status LED is lit in green •...

  • Page 22: Nv Memory (Non-Volatile Memory)

    NV Memory (Non-Volatile Memory) The printer’s NV memory stores data even after the printer power is turned off. NV memory contains the following memory area for the user: • NV graphics memory • Memory switches (customized value) As a guide, NV memory rewriting should be 10 times or less a day when you program applications.

  • Page 23: Product Specifications

    JAN 8 (EAN 8), JAN 13 (EAN 13) CODE 39 CODABAR (NW-7) CODE 93 CODE 128 PDF417 QR CODE Power supply EPSON AC ADAPTER, RA (Model: M266A) Life Mechanism 15,000,000 lines Thermal head 100 million pulses, 100 km Autocutter 1,500,000 cuts...

  • Page 24: Software Specifications

    Print control ePOS-Print API, ePOS-Print XML (XML Web service is used. No printer driver is required.) Utility EPSON TMNet WebConfig  Network setting (Ethernet/Wireless LAN)  Web contents registration  ePOS-Print setting  Following printers with the UB-E02 or UB-R03 embed-...

  • Page 25: Intelligent Section Specifications

    Chapter 1 Product Overview  Following printers with the UB-E02 or UB-R03 embed- Controllable printer SC Model  TM-T88IV  TM-T70*  TM-L90*  TM-U220* *: Firmware Ver.3.0 or later  Following printers with the UB-E02 or UB-R03 embed- KO Model ...

  • Page 26: Printing Specifications

    Printing Specifications Printing method Thermal line printing Dot density 180 × 180 dpi Printing direction Unidirectional with friction feed (Reverse feed is not supported.) Maximum printable width 72.2 mm, 512 dots Character Font A (12 × 24) per line Font B (9 × 17) Maximum High speed mode 170 mm/s...

  • Page 27: Character Specifications

    Chapter 1 Product Overview Character Specifications Number of characters Alphanumeric characters: 95 Extended graphics: 128 × 11 pages (including user-defined page) International characters: 48 Character structure Font A (Initial setting): 12 × 24 (including 2-dot spacing in horizontal) Font B: 9 × 17 (including 2-dot spacing in horizontal) Character size Font A Standard: 1.69 ×...

  • Page 28: Printable Area

    Printable Area In 2-divided energizing, the print position within the printable area of the thermal elements for dots 1 to 256 and 257 to 512 is shifted approximately 0.07 mm {0.0028"} as shown in the figure below in the paper feed direction. In 4-divided energizing, the print position within the printable area of the thermal elements for dots 1 to 96, 97 to 240, 241 to 368, and 369 to 512 is shifted approximately 0.04 mm {0.0016"} as shown in the figure below in the paper feed direction.

  • Page 29: Printing And Cutting Positions

    Chapter 1 Product Overview Printing and Cutting Positions Manual-cutter position Approx. 30 Approx. 15 Autocutter blade position Center of the print dotline Paper feed direction [units: mm (All the numeric values are typical.)] The values above may vary slightly as a result of paper slack or variations in the paper. Take the notice into account when setting the cutting position of the autocutter.

  • Page 30: Electrical Characteristics

    Electrical Characteristics Supply voltage DC 24V: DC 24V ± 5% DC 5V: DC 5V Current consumption Standby Mean: Approximately 0.1A (at 24V, 25°C, normal Maximum 1A for drawer kick-out driving. print density) Operating DC 24V Mean: Approximately 1.8A DC 5V*: Maximum 1.0A/2.5A Note: When print ratio is approximately 18% ...

  • Page 31: Environmental Conditions

    Ambient temperature Acoustic noise (Operating) Approximately 55 dB (Bystander position) Note) The values above are measured in the Epson evaluation condition. The acoustic noise differs depending on the paper used, printing contents, or the setting values such as print speed or...

  • Page 32: External Dimensions And Mass

    External Dimensions and Mass • Height: Approximately 114 mm {4.49"} • Width: Approximately 125 mm {4.92"} • Depth: Approximately 194 mm {7.64"} • Mass: Approximately 1.8 kg {3.96 lb} (except for roll paper) <When the Optional OT-CC70 is installed> 255.5 [Unit: mm]...

  • Page 33: Tm-T70-I Dedicated Ac Adapter

    Chapter 1 Product Overview TM-T70-i Dedicated AC Adapter Input conditions Input voltage: AC 100V to 240V Frequency: 50/60 Hz Input current (rating): 1.3A Output conditions Output voltage (rating): DC 24V ± 5% Output current (rating): 2.1A...

  • Page 34: Option Specifications

    Option Specifications Wireless LAN Cable Set (OT-WL01) Wireless module ELPAP07: 802. 11b/g/n wireless LAN Module (EPSON) Standard IEEE802.11b/g/n (Wi-Fi certificated) SSID 1 to 32 one-byte alphabet and numbers Connection mode Ad hoc mode, Infrastructure mode Authentic method, Encryption algorithm Open+WEP , Shared+WEP , WPA-PSK+TKIP , WPA-PSK+AES,...

  • Page 35: Setup

    Chapter 2 Setup Setup This chapter describes setup and installation of the product and peripherals. Flow of Setup This chapter consists of the following sections along with the setup flow of the product and peripherals. In this setup flow, necessary items are in a frame with a solid line. Optional items are explained in an frame with a dotted line.

  • Page 36: Installing The Printer

    Registering Web Pages (page 71) Setting the Memory Switches (page 74) Installing the Printer You can install this printer only horizontally. Fix the printer so that it does not move around when you open the roll paper cover and cut roll paper.

  • Page 37: Important Notes On Installation

    Chapter 2 Setup If the printer installation does not fit within the specifications shown in the figure below, the following problems may occur. • Cannot set the roll paper in the printer • Cannot cut the paper with the manual cutter Range that manual cutting is possible Shelf height: 150 mm Shelf height: 140 mm...

  • Page 38: Affixing Position Of Df-10

    Affixing Position of DF-10 When you use the affixing tapes for fixing the printer (Model: DF-10), paste them as shown in the figure below. Affixing position of the DF-10...

  • Page 39: Setting The Dip Switches

    Chapter 2 Setup Setting the DIP Switches On this printer, you can make various settings with DIP switches. Setting Procedure Follow the steps below to change the DIP switch settings. Before you remove the DIP switch cover, turn the printer off. Otherwise, a short-circuit may cause the printer to malfunction.

  • Page 40: Functions

    Functions DIP switch bank 1 Factory Function setting Auto line feed Always enabled Always disabled Receive buffer capacity 45 bytes 4 KB Reserved — — Error signal output 7 bits 8 bits 1-5  Reserved — — DIP switch bank 2 Factory Function setting...

  • Page 41: Selecting The Print Density (Dip Switch 2-3/2-4)

    Chapter 2 Setup Selecting the Print Density (DIP Switch 2-3/2-4) Function SW 2-3 SW2-4 Low power consumption mode Print density (Standard) Print density (Darker than standard) Print density (Dark)  If the print density is set to “Darker than standard” or “Dark” level, printing speed may be reduced.

  • Page 42: Connecting The Cash Drawer

    Connecting the Cash Drawer Use the cash drawer handled by EPSON or your dealer. Connecting the Drawer Kick-out Cable  Specifications of drawers differ depending on makers or models. When you use a drawer other than specified, make sure its specification meets the following conditions....
  • Page 43 Chapter 2 Setup Drawer Circuitry Drawer kick-out connector With shielded Drawer kick-out solenoid Drawer open/close switch Printer side User side [Drawer kick-out side]...

  • Page 44: Arranging The Cables

    Arranging the Cables When installing cables without locking connectors (USB cable and DC 5V cable) through the cable exits on the back, fix the cables with the cable band to prevent the cables form coming off. Cable band When attaching the optional connector cover (OT-CC70), use multiple cable exits depending on the number of the cables.

  • Page 45: Connecting The Power Supply Unit

    Chapter 2 Setup Connecting the Power Supply Unit Use the TM-T70-i dedicated AC adapter and the AC cable included with the product as the power supply unit.  Be sure to use the included AC adapter as the power supply unit....

  • Page 46: Connecting The Printer To The System

    Ethernet interface connection diagram 10BASE-T/100BASE-TX DM-D Serial cable Modular cable TM-T70-i Cash drawer Connecting the LAN interface cable  When LAN cables are installed outdoors, make sure devices without proper surge protection are cushioned by being connected through devices that do have surge protection.
  • Page 47 Chapter 2 Setup Connect a 10BASE-T/100BASE-TX cable to the 10BASE-T/100BASE-TX LAN connector by pressing firmly until the connector clicks into place. Ethernet connector...

  • Page 48: For Wireless Lan Interface

    Wireless LAN interface connection diagram Access point Modular cable Cash drawer TM-T70-i Connecting the wireless LAN cable set Check whether the following items are included. If any item is damaged, contact your dealer. • Wireless LAN unit • USB extension cable •...
  • Page 49 Chapter 2 Setup Connecting the unit directly with the printer Install the wireless LAN unit to a USB connector of the printer. USB connector Using the USB extension cable Attach the included rubber cover to the connector of the USB extension cable into which the wireless LAN unit will be inserted, to prevent the unit form coming off.
  • Page 50 Connect the USB extension cable to the USB connector of the printer. If you want to fix the wireless LAN unit, cut the included affixing tape to fit and put on the unit, and fix the unit in a place with good communication. Wireless LAN indicator The position of the wireless LAN indicator is shown in the illustration below.

  • Page 51: Network Setting

    WebConfig" on page 73.  With either connection, wired LAN or wireless LAN, network setting for both the wired LAN and wireless LAN is possible. Wired LAN Setting Follow the steps below to set for wired LAN by using EPSON TMNet WebConfig.
  • Page 52 Connect a PC for setting to the network. Connect the TM-T70-i printer to the network, and turn it on. Print a status sheet. For how to print a status sheet, see "Confirming with a status sheet" on page Set the PC for setting as the same as the setting printed on the status sheet.
  • Page 53 When the printer is set and installed for both of them, only the LAN connection works. Connect a PC for setting to the network. Connect the TM-T70-i printer to the network, and turn it on. Print a status sheet. For how to print a status sheet, see "Confirming with a status sheet"...
  • Page 54 Start up the web browser on the PC for setting, and enter the printer’s IP address printed on the status sheet in the address bar as shown below. http://xxx.xxx.xxx.xxx/PrinterConfigurationPage/ EPSON TMNet WebConfig starts. Select [Configuration], [Wireless], and then [TCP/IP]. The [TCP/IP Setting (Wireless)] screen appears.

  • Page 55: Security Setting

    Chapter 2 Setup Security setting Set the following items depending on the network mode. Item Description Network Mode Set the communication mode (Infrastructure/Ad-Hoc). SSID Same value as that for access point. 32 alphanumeric characters at maximum. Ad-Hoc Channel Set when [Ad-Hoc] is selected for [Network Mode]. Selectable from 1 to 11.
  • Page 56  Initially, Authentication Method is set to Open System and Security Mode is set to None with the firmware version 2.00 or later. To ensure security, be sure to change the settings before use.  The following restrictions apply to the characters that can be specified for SSID, WEP keys, and WPA/WPA2 pre-shared keys.
  • Page 57 Chapter 2 Setup Confirming Network Setting You can confirm the network setting with a status sheet or EPSON TMNet WebConfig. Confirming with a status sheet Make sure the printer is turned on, press the push button at the interface part for approximately 3 seconds.
  • Page 58 Item Description General Information Shows the general information. Software Shows the printer’s software version. Model Shows [TM-T70-i]. Time Shows the present time and time difference Wired Shows wired LAN settings. MAC Address Shows the MAC address. Link Speed & Duplex Shows the speed of data link layer.
  • Page 59 Chapter 2 Setup Item Description Wireless TCP/IP Shows TCP/IP settings for wireless LAN. Get IP Address Shows the method of getting the IP address. Set using Automatic Private IP Addressing (APIPA) Shows the APIPA setting. IP Address Shows the IP address. Subnet Mask Shows the subnet mask.
  • Page 60 Item Description When Automatic Update Setting is enabled: Shows the date and time when the web contents (zip file) were created. Date of Installed Web Contents When Automatic Update Setting is disabled: Shows the date and time when the web contents were uploaded.
  • Page 61 Confirming with EPSON TMNet WebConfig Start up a PC for setting. Connect the TM-T70-i printer to the network, and turn it on. Start up the web browser on the PC for setting, and enter the printer’s IP address in the address bar as shown below.
  • Page 62 Initializing the Network Setting When network connection fails, follow the steps below to initialize the network setting to the default. For firmware version 3.00 and later, the TMNet WebConfig password is also initialized. Load the paper on the printer and turn on the printer. Push and hold the push button for 10 seconds or longer.

  • Page 63: Establishment Of Epos-Print System

     For details on ePOS-Print, see ePOS-Print API User’s Manual or ePOS-Print XML User’s Manual.  Regarding the system configuration for ePOS-Print API, the configuration method for the system for registering web applications in TM-T70-i (page 67) is explained in this manual.
  • Page 64 ePOS-Print API • As long as you are within a network environment, you can print from anywhere on a device with an HTML5 compatible web browser. • No need to install drivers or plugins. • No need to set up a computer or server for printing. •...

  • Page 65: Examples Of System Establishment

    Chapter 2 Setup Examples of System Establishment Depending on where a web application is registered, the following examples of the system establishment are possible. • Registering on the TM-T70-i • Registering on a web server Registering on the TM-T70-i Wireless...
  • Page 66 Input terminal TM-T70-i • Web server: The web application is installed. • Input terminal: Executes the web application from a browser (HTML 5 compliant). • TM-T70-i: Receives the print document sent from the web browser, prints receipts, or controls other devices.

  • Page 67: Setting For Connected Devices

    Chapter 2 Setup Setting for Connected Devices Follow the steps below to set for devices controlled by the TM-T70-i printer by using EPSON TMNet WebConfig.  This printer cannot be deleted from a device.  The "device ID" for this printer can be changed.
  • Page 68 Select [Configuration], and then [Device]. The [Device Settings] screen appears. Set for the following items, and click [Register]. The information of the registered devices is shown in [Device List]. Item Description Device ID Set an ID for a device to be controlled. Model number Select an model for a device to be controlled.

  • Page 69: Registering Web Pages

    Chapter 2 Setup Registering Web Pages When you register an application on the TM-70-i printer, register web contents. Specifications of the file to be registered • Static contents such as HTML files, CSS files, JavaScript files, and image data. • Zip the files to be registered all together. The zip file name is arbitrary. ...
  • Page 70 • When you access to registered web contents from an input terminal and so on, the URL differs depending on the folder structure in the zip file. ➀ http://[the TM-T70-i printer’s IP address]/index.html ➁ http://[the TM-T70-i printer’s IP address]/webpage/index.html ➀...

  • Page 71: How To Register

    Start up a PC for setting. Connect the TM-T70-i printer to the network, and turn it on. Start up the web browser on the PC for setting, and enter the TM-T70-i printer’s IP address in the address bar. EPSON TMNet WebConfig starts.

  • Page 72: Setting The Memory Switches

    Setting the Memory Switches With the “memory switch (customized value”), which is a software switch of this printer, you can set: • Print density • Print speed • Number of head energizing parts Use the Memory Switch Setting Utility to set the memory switches. ...

  • Page 73: Application Development Information

    TM-T70-i (firmware version 2.00 or later). TM-i series PHP Setup Manual See this manual when you establish the environment where you use the PHP function and store data in micro SD cards with the TM-T70-i (firmware version 2.00 or later).

  • Page 74: Download

    Drivers, utilities, and manuals can be downloaded from one of the following URLs. For customers in North America, go to the following web site: http://www.epsonexpert.com/ and follow the on-screen instructions. For customers in other countries, go to the following web site: https://download.epson-biz.com/?service=pos/...

  • Page 75: Epson Tmnet Webconfig

    Chapter 3 Application Development Information EPSON TMNet WebConfig EPSON TMNet WebConfig is a Utility to set the printer on a web browser. This section describes EPSON TMNet WebConfig using Internet Explorer as a browser. With the firmware version 2.00 or later, you can also use API to set or check this product.

  • Page 76: General Information

    General Information You can check the general information of the TM-T70-i. Item Description Administrator Name Shows the administrator name. Location/Person Shows the user name Software Version Shows the software version of the TM-T70-i. Printer Serial Number Shows the serial number of the TM-T70-i.
  • Page 77 Chapter 3 Application Development Information Item Description Wireless MAC Address Shows the MAC address for wireless LAN. Hardware Version Shows the hardware version for wireless LAN. Software Version Shows the software version for wireless LAN. Communication Standard Shows the communication standard. Network Mode Shows the communication mode.

  • Page 78: Tcp/Ip Information (Wired)

    TCP/IP Information (Wired) You can check the TCP/IP setting for a wired LAN. Item Description Get IP Address Shows the method of getting the IP address. Set using Automatic Private IP Addressing Shows the APIPA setting. (APIPA) IP Address Shows the IP address when [Get IP Address] is set to [Manual].

  • Page 79: Tcp/Ip Information (Wireless)

    Chapter 3 Application Development Information TCP/IP Information (Wireless) You can check the TCP/IP setting for a wireless LAN when the optional wireless LAN cable set (OT-WL01) is used. Item Description Get IP Address Shows the method of getting the IP address. Set using Automatic Private IP Addressing Shows the APIPA setting.

  • Page 80: Web Contents Update Information

    Date of Last Automatic Shows the latest date and time when the web Update contents were installed on the TM-T70-i automatically. Status of Last Automatic Shows the result of the last update of web contents Update...

  • Page 81: Time Information

    Chapter 3 Application Development Information Time Information You can check the time setting. Item Description Time Shows the present time. Use Time Server Shows whether time server is used for time setting. Get Time Server Shows the method of getting time server. Time Server Shows the IP address or host name of the time server.

  • Page 82: Wired Setting

    Wired Setting You can make settings for a wired LAN network. Item Description Link Speed & Duplex Sets the speed of data link layer. Submit Submits the setting to the TM-T70-i.

  • Page 83: Tcp/Ip Setting (Wired)

    Sets the method of getting the address of the DNS Automatically server. DNS Server Address Sets the addresses of the DNS server in order of usage when [Acquire DNS Server Address Automatically] is set to [Disable]. Submit Submits settings to the TM-T70-i.

  • Page 84: Wireless Setting

    Wireless Setting You can make settings for a wireless LAN network when the optional wireless LAN cable set (OT-WL01) is used. Item Description Network Mode Sets the communication mode. SSID Sets the SSID. Ad-Hoc Channel Sets the ad-hoc channel. (Available only in the ad-hoc mode) Communication Standard Sets the communication standard.
  • Page 85 Sets the network key. Submit Submits settings to the TM-T70-i.  Initially, Authentication Method is set to Open System and Security Mode is set to None with the firmware version 2.00 or later. To ensure security, be sure to change the set- tings before use.

  • Page 86: Tcp/Ip Setting (Wireless)

    Sets the method of getting the address of the DNS Automatically server. DNS Server Address Sets the addresses of the DNS server in order of usage when [Acquire DNS Server Address Automatically] is set to [Disable]. Submit Submits settings to the TM-T70-i.

  • Page 87: Device Settings

    Chapter 3 Application Development Information Device Settings You can set devices controlled by the TM-T70-i or check their operation.  Setting the TM-T70-i printer itself is not possible.  You can change the device ID for the TM-T70-i printer. Item...

  • Page 88: Web Contents Update Settings

    Web Contents Update Settings You can set how to install and update web contents to register on the TM-T70-i or update them. See also "Registering Web Pages" on page Item Description Automatic Automatic Update Sets the method of installing web contents.
  • Page 89 When [Yes] is selected, set [Proxy URL and Port Number]. Proxy URL and Port Number Sets the URL and port number for the proxy server to use. Submit Submits settings to the TM-T70-i. Web Contents Web Contents Archive File Specifies the web contents to install. Manual Update (*.zip)
  • Page 90 Server Direct Print Setting You can set server direct print for the TM-T70-i. Item Description Server Direct Print Sets whether to use the Server Direct Print function or not. Sets the web server ID when [Server Direct Print] is set to [Enable].
  • Page 91 Chapter 3 Application Development Information Status Notification Setting You can set the information for the administrator of the TM-T70-i. Item Description Administrator Name Sets the name of the administrator of the TM-T70-i. Sets the web server ID when [Status Notification] is set to [Enable].

  • Page 92: Administrator Setting

    Administrator Setting You can set the information for the administrator of the TM-T70-i. Item Description Administrator Name Sets the name of the administrator of the TM-T70-i. Location/Person Sets the location where the TM-T70-i is installed. Submit Submits settings to the TM-T70-i.

  • Page 93: Time Setting

    Chapter 3 Application Development Information Time Setting You can set the time for the TM-T70-i. Item Description Time Sets the time. Clicking [Get Time] shows the present time. Time Zone (Hour) Sets the time zone. Time Server Use Time Server...

  • Page 94: Password Setting

    Submits settings to the TM-T70-i. A user name and a password will be required on the authentication screen when you start up this utility and when you change settings. Enter “epson” for the user name and the pass- word you set for the password.

  • Page 95: Reset

    Resets the network interface, and reboots wired LAN and wireless LAN functions after applying the changes made in the settings window. Factory Default Returns settings of the TM-T70-i to default ones. All settings are initialized, except for the internal clock.

  • Page 96: Setting Check Modes

    Setting Check Modes Besides the ordinary print mode, the printer has a self-test mode and hexadecimal dumping mode to check settings of the printer. Self-test Mode You can confirm the following printer functions by running the self-test. • Control circuit functions •...

  • Page 97: Hexadecimal Dumping Mode

    Chapter 3 Application Development Information Hexadecimal Dumping Mode In the hexadecimal dumping mode, the printer prints the data transmitted from a host computer in hexadecimal numbers and their corresponding characters. Starting hexadecimal dumping Follow the steps below to perform the hexadecimal dumping. ...

  • Page 98: Network Setting

    Easy Setup Easy Setup is a function that saves the settings for the TM-i EPSON TMNet WebConfig on USB memory, copying it to a different TM-i. You can perform settings for multiple TM-i devices quickly and efficiently. If you are using a printer that can be controlled (a TM printer connected to a network), you can also perform their network settings at the same time.

  • Page 99: Handling

    Chapter 4 Handling Handling This chapter describes basic handling of the printer. Installing and Replacing Roll Paper  Do not open the roll paper cover during printing. The printer may be damaged.  Do not touch the manual cutter with your hands when installing or replacing the WARNING roll paper....
  • Page 100 Pull out some roll paper, and make sure that the roll paper is set between the paper guides. Paper guides Close the roll paper cover. Tear off the roll paper.

  • Page 101: Removing Jammed Paper

    Remove the jammed paper, reinstall the roll, and close the roll paper cover. Cleaning the Thermal Head Epson recommends cleaning the thermal head periodically (generally every 3 months) to maintain receipt print quality. After printing, the thermal head can be very hot. Do not touch it and let it cool before you clean it.

  • Page 102: Connecting To External Devices

    Connecting to External Devices Follow the steps below to connect external devices to the interface section.  When connecting external devices to the USB (including Micro-USB) connectors, follow the precautions below.  Confirm the rated current of the external devices by checking the descriptions CAUTION on the devices or manuals.

  • Page 103: Preparing For Transport

    Chapter 4 Handling Preparing for Transport Follow the steps below to transport the printer. Turn off the printer. Confirm that LED is off. Remove the power supply connector. Remove the roll paper. Pack the printer upright.

  • Page 105: Appendix

    Appendix Appendix Character Code Tables  The character code tables show only character configurations. They do not show the actual print pattern.  “SP” in the table shows a space. Common to All Pages When International character set (See "International Character Sets" on page 109.) is USA: "...

  • Page 106: Pc437: Usa, Standard Europe]

    Page 0 [PC437: USA, Standard Europe] Ç É á ░ └ ╨ α ≡ í ü æ ▒ ┴ ╤ β ± Γ é Æ ó ▓ ┬ ╥ ≥ â ô ú │ ├ ╙ π ≤ ä ö ñ...

  • Page 107: Katakana)

    Appendix Page 1 (Katakana) ┴ ═ ┬ ╞ ┤ ╪ ├ ╡ ¯ ─ │ │ ┌ ♠ ┐ ♥ └ ♦ ┘ ♣ ● ○ ▓ ┼...

  • Page 108: Pc850: Multilingual)

    Page 2 (PC850: Multilingual) Ç É á ░ └ ð Ó í ü æ ▒ ┴ Ð β ± é Æ ó ▓ ┬ Ê Ô â ô ú │ ├ Ë Ò ¾ ä ö ñ ┤ ─ È õ...

  • Page 109: Pc860: Portuguese)

    Appendix Page 3 (PC860: Portuguese) Ç É á ░ └ ╨ α ≡ í ü À ▒ ┴ ╤ β ± Γ é È ó ▓ ┬ ╥ ≥ â ô ú │ ├ ╙ π ≤ ã õ ñ ┤...

  • Page 110: Pc863: Canadian-French)

    Page 4 (PC863: Canadian-French) Ç É ¦ ░ └ ╨ α ≡ ´ ü È ▒ ┴ ╤ β ± Γ é Ê ó ▓ ┬ ╥ ≥ â ô ú │ ├ ╙ π ≤ Â Ë ¨ ┤ ─...

  • Page 111: Pc865: Nordic)

    Appendix Page 5 (PC865: Nordic) Ç É á ░ └ ╨ α ≡ í ü æ ▒ ┴ ╤ β ± Γ é Æ ó ▓ ┬ ╥ ≥ â ô ú │ ├ ╙ π ≤ ä ö ñ ┤...

  • Page 112: Wpc1252)

    Page 16 (WPC1252) € ° À Ð à ð ‘ ¡ ± Á Ñ á ñ ‚ ’ ¢ ² Â Ò â ò ƒ “ £ ³ Ã Ó ã ó ´ „ ” ¤ Ä Ô ä ô …...

  • Page 113: Pc866: Cyrillic #2)

    Appendix Page 17 (PC866: Cyrillic #2) А Р а ░ └ ╨ р Ё Б С б ▒ ┴ ╤ с ё В Т в ▓ ┬ ╥ т Є Г г У │ ├ ╙ у є Ї Д Ф...

  • Page 114: Pc852: Latin2)

    Page 18 (PC852: Latin2) Ç É á ░ └ đ Ó í ü Ĺ ▒ ┴ Ð β ˝ ĺ é ó ▓ ┬ Ď Ô ˛ â ô ú │ ├ Ë Ń ˇ ä ö Ą ┤ ─ d ˇ...

  • Page 115: Pc858: Euro)

    Appendix Page 19 (PC858: Euro) Ç É á ░ └ ð Ó í ü æ ▒ ┴ Ð β ± é Æ ó ▓ ┬ Ê Ô â ô ú │ ├ Ë Ò ¾ ä ö ñ ┤ ─ È...

  • Page 116: User-Defined Page)

    Page 255 (User-Defined Page)

  • Page 117: International Character Sets

    Appendix International Character Sets ASCII code (Hex) Country France à ° ç § é ù è ¨ Germany § Ä Ö Ü ä ö ü β U.K. £ Denmark I Æ Ø Å æ ø å Sweden ¤ É Ä Ö...

Table of Contents