SPECIFICATIONS Tuner section General Frequency range Speaker 100 mm cone type (2) FM : 87.5 MHz - 108.0 MHz Output Headphones jack (stereo mini-jack) Antenna : Rod antenna Power output 2.5 W + 2.5 W (EIAJ 7 ohms, THD 10%) AM : 530 kHz - 1,605 kHz 1.9 W + 1.9 W (DIN 1% Rated Power)
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING This set employs laser. Therefore, be sure to follow carefully CAUTION the instructions below when servicing. Use of controls or adjustments or performance of proce- dures other than those specified herin may result in WARNING!! hazardous radiation exposure.
TRANSISTOR ILLUSTRATION E C B B C E E C B 2SA933SS 2SB1370E 2SA1296GR 2SC2714 2SC1740SS 2SA1318TU DTC114TK DTC114TS 2SC1815Y DTC114YK DTC124XS DTC114YS DTC144EK – 7 –...
Page 17
IC DESCRIPTION IC, LC78622ED Pin No. Pin Name Description DEFI Defect detection signal (DEF) input. Test input. A pull-down resistor is built in. Must be connected to 0V. External VCO control phase comparator output. VVSS – Internal VCO ground. Must be connected to 0V. ISET PDO output current adjustment resistor connection.
Page 18
Pin No. Pin Name Description LVSS – Left channel one-bit D/A converter ground. Must be connected to 0V. RVSS – Right channel one-bit D/A converter ground. (Must be connected to 0V.) RCHO Right channel onr-bit D/A converter output. RVDD – Right channel one-bit D/A converter power supply.
Page 19
IC, LA9241ML Description Pin No. Pin Name For the connection of the pickup photodiode. Addition to the FIN1 pin creates an RF FIN2 signal and subtraction from it create an EF signal. FIN1 For the connection of the pickup photodiode. For the connection of the pickup photodiode.
Page 20
Pin No. Pin Name Description The HFL (high frequency level) signal is used to judge whether the main beam is positioned on the pit or on the mirror. SLOF Sled servo off control input. CV– CLV error signal input from the DSP. RFSM RF output.
Page 21
IC, LC865516A-5L26 Pin No. Pin Name Description SEG E SEG E control. SEG F SEG F control. SEG G SEG G control. – Not connected. I-RES Microprocessor reset input. XT1 (IN) Connected to an external 32.768 kHz crystal oscillator. – Not connected.
Page 22
Pin No. Pin Name Description Not connected. – SEG DP control. SEG DP SEG A control. SEG A SEG B control. SEG B SEG C control. SEG C SEG D control. SEG D Not connected. – – 22 –...
Page 23
ADJUSTMENT <TUNER / CD / DECK> D TUNER C.B TP6 (RCH) TP5 (LCH) L009 IC001 L006 L007 L005 L008 PVC001 TC001 TC003 TC004 TC002 L004 L003 < TUNER SECTION > 5. FM Tracking Adjustment 1. AM Frequency Range Adjustment • Test Point: TP5 (LCH), TP6 (RCH) •...
B CD C.B IC404 IC401 SFR430 A MAIN C.B L801 < CD SECTION > 1. Focus Bias Adjustment Make the focus bias adjustment when replacing and repairing the optical block. Oscilloscope (DC range) EYE PATTERN must be CLEAR and MAX VOLT / DIV: 200mV TIME / DIV: 0.5µs <...
TAPE MECHANISM PARTS LIST 1 / 1 REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION 1 S1-921-030-4A0 HEAD BASE 36 S1-921-140-030 REC BUTTON LEVER 2 S1-821-030-070 AZIMUTH SPRING 37 S1-921-140-170 P.S.LEVER SPRING 3 S1-921-030-090 PANEL P SPRING 38 S1-921-073-040 RF CLUTCH ASSY 4 S1-921-260-050...