Advertisement
2
PREPARATION BEFORE USE
Preparing Filters
1. Open the air inlet grille and remove the air filters.
2. Attach the filters. (see detail in the accessory sheet).
Loading Batteries
1. Remove the battery cover.
2. Insert 2 new batteries (AAA type)
following the (+) and (–) positions.
Clock Setup
1. Push CLOCK
by tip of the pencil.
●
If timer indication is flashing, go to the next step 2.
2. Press
or
: adjust the time.
ON
OFF
3. Press
: Set the time.
SET
Remote Control Reset
1. Remove the batteries.
2. Press
.
3. Insert the batteries.
3
AIR FLOW DIRECTION
FIX
1
Press
: Move the louver in the
desired vertical direction.
SWING
2
Press
: Swing the air
automatically and press again to stop.
3
For horizontal direction, adjust manually.
Note:
•
Do not move the louver manually by others.
The louver may automation positioning by some operation mode.
•
4
REMOTE CONTROL
1 Infrared signal emitter
2 Start/Stop button
3 Mode select button (MODE)
4 Temperature button (TEMP)
5 Fan speed button (FAN)
6 Swing louver button (SWING)
7 Set louver button (FIX)
8 On timer button (ON)
9 Off timer button (OFF)
! Sleep timer button (SLEEP)
" Setup button (SET)
# Clear button (CLR)
$ Memory and Preset button (PRESET)
% One-Touch button (ONE-TOUCH)
& High power button (Hi-POWER)
( Economy button (ECO)
) Quiet button (QUIET)
~ Comfort sleep button (COMFORT SLEEP)
+ Plasma Air Purifier button (PURE)
, Filter reset button (FILTER)
- Clock Reset button (CLOCK)
. Check button (CHK)
5
ONE-TOUCH
Press the "ONE-TOUCH" button for fully automated operation that is customized
to the typical consumer preferences in your region of the world. The customized
settings control temperature air flow strength, air flow direction and other settings
to provide you alternate contact with "ONE-TOUCH" of the button. If you prefer
other settings you can select from the many other operating functions of your
Toshiba unit.
ONE-TOUCH
Press
: Start the operation.
6
AUTOMATIC OPERATION
To automatically select cooling, heating, or fan only operation
MODE
1. Press
: Select A.
2. Press
TEMP
: Set the desired temperature.
7
COOLING / HEATING / FAN ONLY OPERATION
MODE
1. Press
: Select Cool
, Heat
2. Press
TEMP
: Set the desired temperature.
Cooling: Min. 17
C, Heating: Max. 30
o
o
FAN
3. Press
: Select AUTO, LOW , LOW+
HIGH
.
8
DRY OPERATION
For dehumidification, a moderate cooling performance is controlled automatically.
MODE
1. Press
: Select Dry
.
TEMP
2. Press
: Set the desired temperature.
9
AIR PURIFYING OPERATION
PURE
Press
to start and stop plasma air purifier and air ionizer operation.
The plasma air purifier and air ionizer can be activated or deactivated by pressing
the PURE button. The air ionizer starts in conjunction with plasma air purifier
operation.
Note: The FILTER indicator (orange) turns on after PURE operation is performed
for about 1000 hours.
10
Hi-POWER OPERATION
To automatically control room temperature and airflow for faster cooling or
heating operation (except in DRY and FAN ONLY mode)
Hi-POWER
Press
: Start and stop the operation.
11
ECO OPERATION
To automatically control room to save energy (except in DRY and FAN ONLY mode)
ECO
P ress
: Start and stop the operation.
Note: Cooling operation; the set temperature will increase automatically 1 degree/
hour for 2 hours (maximum 2 degrees increase). For heating operation the
set temperature will decrease.
12
TEMPORARY OPERATION
In case of the misplaced or discharged remote control
•
Pressing the RESET button, the unit can start or
stop without using the remote control.
Operation mode is set on AUTOMATIC operation,
•
preset temperature is 24°C and fan operation is
automatic speed.
13
TIMER OPERATION
Set the timer when the air conditioner is operating.
Setting the ON Timer
1
Press
: Set the desired
ON
ON timer.
2
Press
: Set the timer.
SET
3
Press
: Cancel the timer.
CLR
Daily timer allows the user to set both the ON & OFF timers and will be
activated on a daily basis.
Setting Everyday Timer
1
ON
Press
: Set the ON timer.
2
OFF
Press
: Set the OFF timer.
•
During the every day timer is activating, both arrows ( , ) are indicated.
Note:
Keep the remote control in accessible transmission to the indoor unit;
•
otherwise, the time lag of up to 15 minutes will occur.
•
The setting will be saved for the next same operation.
, or Fan only
.
C, Fan Only: No temperature indication
, MED
, MED+
, or
Setting the OFF Timer
Press
: Set the desired
OFF
OFF timer.
Press
: Set the timer.
SET
Press
: Cancel the timer.
CLR
3
Press
.
SET
Press
button during the
SET
4
( or ) mark flashing.
Advertisement
