Table of Contents
Advertisement
LIMITED WARRANTY
Bass Inferno warrants any products purchased in the U.S.A.
from an authorized Bass Inferno dealer. All products are warranted to
be free from defects in material and workmanship under normal use
and service for a period of one (1) year. This warranty applies to the
original purchase only.
Bass Inferno will either repair or replace (as its option) any unit
that has been found to be defective and under warranty provided the
defect occurs within the one (1) year warranty period.
This limited warranty does not extend to units have been
subjected to misuse, abuse, neglect, or accident. In Bass Inferno's
judgment, products that show evidence of having been altered, modi-
fied, or serviced without Bass Inferno's authorization, will be ineligible
under this warranty.
To obtain warranty service please contact your retailer or visit
our website at www.bassinferno.com for more details.
DB Research L.L.P.
302 Hanmore Industrial Parkway // Harlingen, TX 78550
ph: 877.787.0101 // fx: 956.421.4513 // www.bassinferno.com
®
BI4500.4 BI4800.4 BI1750M BI3000D
AMPLIFIERS
Instruction Manual
• Installation Instructions / Owners Manual •
Due to continuous improvement of the product the Specifications are subject to change without notice.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Bass Inferno BI4500.4
Summary of Contents for Bass Inferno BI4500.4
-
Page 1: Limited Warranty
(1) year. This warranty applies to the original purchase only. Bass Inferno will either repair or replace (as its option) any unit that has been found to be defective and under warranty provided the BI4500.4 BI4800.4 BI1750M BI3000D... -
Page 2: Safety Precautions
Congratulations on your purchase of a Bass Inferno state-of-the-art power amplifier. Your use amplifiers power wire at the battery selection of a Bass Inferno car audio product indicates a true appreciation of fine musical reproduction. Whether adding to an existing system or including your Bass Inferno Be sure to fuse the power wire within 12”... -
Page 3: Features And Benefits
The BI Series amplifiers feature a state of the art variable crossover. The BI1750M and BI3000D use a 12db per octave slope to filter all unwanted high frequencies. The BI4500.4 and BI4800.4 include both a Highpass and Lowpass filter. The BI3000D features an internal Multi-Linking module. -
Page 4: Mounting Location
OUNTING LOCATION OWER CONNECTIONS Before you start the installation, it will be necessary to find a mounting location for the ampli- fier. Find a location in which the amplifier will receive adequate ventilation in order to dissipate the heat it develops during operation. Two popular mounting locations are in the trunk or under the seat. -
Page 5: Signal Connections
PEAKER CONNECTIONS IGNAL CONNECTIONS (BI1750M, BI3000D) IMPORTANT! The following speaker connection are for the amplifier in normal mono Connect the RCA output of the head unit (AM/FM cassette player, CD, or configuration. DAT) to the RCA input terminals of the amplifier. Make the speaker connections using speaker wire that is at least 16 gauge or heavier. - Page 6 4 CHANNEL SPEAKER CONNNECTION 4 CHANNEL BRIDGED CONNECTIONS BI4800.4 - BI4800.4 - 4 Channel Stereo Amplifier 4 Channel Stereo Amplifier 4 Ohm Speaker 4 Ohm Speaker 4 Ohm Speaker 4 Ohm Speaker 4 Ohm Speaker 4 Ohm Speaker BI4500.4 and BI4800.4...
-
Page 7: Multi Link Connection
Set to Slave EMOTE BASS CONTROL MODULE The gain sensitivity control for the “Bass Inferno” amplifier is located on the side panel. This gain control has been included to allow adjustment to properly match the output of Before connecting the remote, it will be necessary to find a mounting location that will be the radio. - Page 8 +12V at power terminal Check connection +12V at remote terminal Check connection Grounding point clean and tight Check for ground w/meter BI4500.4 BI4800.4 Head Unit’s fader not in center position Set to center position Output Power : Master & Slave settings...
Need help?
Do you have a question about the BI4500.4 and is the answer not in the manual?
Questions and answers