Table of Contents
Advertisement
Quick Links
LIMITED WARRANTY
Bass Inferno warrants any products purchased in the U.S.A.
from an authorized Bass Inferno dealer. All products are warranted to
be free from defects in material and workmanship under normal use
and service for a period of one (1) year. This warranty applies to the
original purchase only.
Bass Inferno will either repair or replace (as its option) any unit
that has been found to be defective and under warranty provided the
defect occurs within the one (1) year warranty period.
This limited warranty does not extend to units have been
subjected to misuse, abuse, neglect, or accident. In Bass Inferno's
judgment, products that show evidence of having been altered, modi-
fied, or serviced without Bass Inferno's authorization, will be ineligible
under this warranty.
TM
AMPLIFIERS
Bi2200Tx
Bi1400Mx
Bi2400Mx
4-CHANNEL AMPLIFIER
Instruction Manual
• Installation Instructions / Owners Manual •
Due to continuous improvement of the product the Specifications are subject to change without notice.
TM
Bi4200Fx
Bi3000Mx
X
X
X
X
X
X
X
X
TM
X
X
WATTS
X
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Bass Inferno Bi2200Tx
Summary of Contents for Bass Inferno Bi2200Tx
- Page 1 (1) year. This warranty applies to the original purchase only. Bass Inferno will either repair or replace (as its option) any unit that has been found to be defective and under warranty provided the defect occurs within the one (1) year warranty period.
-
Page 2: Safety Precautions
Congratulations on your purchase of a Bass Inferno state-of-the-art power amplifier. Your selection of a Bass Inferno car audio product indicates a true appreciation of fine musical reproduction. Whether adding to an existing system or including your Bass Inferno Be sure to fuse the power wire within 12”... -
Page 3: Features And Benefits
Built-in Crossover Bi3000Mx-1 Ohm Mono The Bass Inferno amplifiers feature a state of the art variable crossover. The Bi1400Mx, Bi2400Mx and Bi3000Mx use a 12db per octave slope Low Pass Crossover to filter all unwanted high frequencies. The BI2200Tx and BI4200Fx include both a Highpass and Lowpass filter. -
Page 4: Mounting Location
OUNTING LOCATION OWER CONNECTIONS Before you start the installation, it will be necessary to find a mounting location for the ampli- GROUND REMOTE FUSE fier. Find a location in which the amplifier will receive adequate ventilation in order to dissipate the heat it develops during operation. Two popular mounting locations are in the trunk or under the seat. -
Page 5: Signal Connections
INPUT OUTPUT BASS BOOST X-OVER LEVEL FUSE 0 6 12 GROUND REMOTE High Level 50Hz 250Hz 120Hz 3KHz Bi2200Tx 800 WATTS 2-CHANNEL : CLASS AB POWER INPUT SPEAKER OUTPUT SINGLE SUBWOOFER CONNECTION GROUND REMOTE FUSE INPUT OUTPUT INPUT X-OVER X-OVER... - Page 6 CH 3 CH 4 CH 1 CH 2 CH 3 CH 4 POWER INPUT POWER INPUT BRIDGED BRIDGED BRIDGED BRIDGED 4 Ohm Speaker 4 Ohm Speaker 4 Ohm Speaker 4 Ohm Speaker 4 Ohm Speaker 4 Ohm Speaker Bi2200Tx and Bi4200Fx...
-
Page 7: Adjustments And Settings
INE TUNE THE SYSTEM Fine tune the amplifier’s input sensitivity The gain sensitivity control for the “Bass Inferno” amplifier is located on the side panel. This gain control has been included to allow adjustment to properly match the output of the radio. -
Page 8: Troubleshooting The System
Bad RCA Cable(s) Replace +12V at power terminal Check connection Bi4200Fx +12V at remote terminal Check connection Bi2200Tx Output Power : Grounding point clean and tight Check for ground w/meter 4 ohm 4 x 200W 2 x 200W Head Unit’s fader not in center position...
Need help?
Do you have a question about the Bi2200Tx and is the answer not in the manual?
Questions and answers